Graco Optimiser 02017 Instructions Manual page 26

Cleaning Brush 105–749
For use in cleaning gun
Lubricant 111–265
One 4 oz. (113 gram) tube sanitary (non-silicone)
lubricant for fluid seals and wear areas.
Fluid Tube Kit 236–318
Allows air and fluid hoses to be
more easily strapped together
and eases gun movement by
the operator.
High Pressure Air Cap 189–755
Optimal air cap for use in non-HVLP compliant opera-
tions. Water-base compatible
Air Pressure Verification Kit 224–187
For use in checking gun atomizing air pressure at
various supply air pressures. Not to be used for
actual spraying.
Assemble kit as shown in
drawing below. Screw
tube connector into gun's
side port. Turn on the air
to the gun, then trigger the
gun and read the resulting air pressure.
NOTE: To be "HVLP compliant", the atomizing air
pressure must not exceed 10 psi (70 kPa, 0.7 bar).
SST Fluid Pressure Regulator
100 psi (0.7 MPa, 7 bar) Maximum Inlet Pressure
3–30 psi (21–210 kPa, 0.2–2.1 bar)
Regulated Pressure Range
To regulate the fluid pressure to the gun.
1/4 npt(f) inlet and outlet
236–081 Regulator without
pressure gauge
236–449 Regulator with pressure gauge
Air Hose Assembly 210–867
100 psi (0.7 MPa, 7 bar) Maximum Working Pressure
25 ft. (7.625 m) long, 5/16 in. (7.94 mm) ID, 1/4
npsm(f) swivel, buna-n
Air Hose Assembly 185–353
100 psi (0.7 MPa, 7 bar) Maximum Working Pressure
Optional air hose for use when higher air flow is
required. 25 ft. (7.625 m) long, 3/8 in. (9.53 mm) ID,
1/4 npsm(f) swivel, buna-n
26 308–293
Accessories
Air Hose Quick-disconnect
Install between gun air inlet fitting and air hose.
208–536
169–970
Fluid Hose Assembly 205–142
300 psi (2.1 MPa, 21 bar) Maximum Working Pressure
Nylon with neoprene cover, 0.25 in. (2.4 mm) ID,
3/8 npsm(fbe), 25 ft. (7.6 m) long
Air Filter and Moisture Separator 106–149
250 psi (1.7 MPa, 17.4 bar) Maximum
Working Pressure
Removes moisture, oil, and other contami-
nants from the compressed air supply.
1/2 npt(fbe)
Air Pressure Regulator Kit 210–613
300 psi (2.1 MPa, 20 bar) Maximum
Inlet Pressure
0-125 psi (0–0.87 MPa, 0-8.75 bar)
Regulated Pressure Range
To regulate the air pressure to the gun.
Includes gauge, air shutoff valve, and
fittings. 1/4 npt(m)
Air Shutoff Valve 208–390
500 psi (3.4 MPa, 34 bar) Maximum Working Pressure
To shutoff air supply line. 1/4 npt(m)
Gun Air Regulator Assy. 235–119
0–100 psi (0–0.7 MPa, 0–7 bar) air
regulator to control air to gun
SST Pressure Cup Kit 235–373
with single air regulator
1 qt. (0.95 liter) capacity, 304 stainless
steel cup. Includes a pressure relief
valve and a single air regulator and
gauge.
Coupler, 1/4 npt(f)
Nipple, 1/4 npt(m)