Advertisement
Quick Links
OPERATION -
UTILIZAÇÃO -
FONCTIONNEMENT -
FUNCIONAMIENTO
GMaxt 5900 Convertible Sprayers
233709 - 233715
3300 psi (228 bar, 22.8 MPa) Maximum Working Pressure
Pressão máxima de trabalho de 3300 psi (228 bar, 22.8 MPa)
Paression maximale de service 3300 lb/po
Presión máxima de operación 3300 psi (228 bar, 22.8 MPa)
All models not available in all countries.
Nem todos os modelos existem à disposição em todos os países.
Tous les modèles ne sont pas disponibles dans tous les pays.
Hay modelos que no se distribuyen en todos los países.
S Controls
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
2
(228 bar, 22.8 MPa)
3
6
8
. . . . . . .
12
19
19
23
ECOPYRIGHT 2002, GRACO INC.
Graco Inc. is registered to I.S. EN ISO 9001
309410
8841A
233709
Rev. B
Advertisement
Related Manuals for Graco 309410
Summary of Contents for Graco 309410
-
Page 1: Table Of Contents
......GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 (228 bar, 22.8 MPa) ..ECOPYRIGHT 2002, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001 309410 Rev. B 8841A 233709... - Page 2 Si un fluide haute pression perce la peau, la blessure peut paraître une “simple coupure” Mais il s’agit bien d’une lésion grave! Consulter immédiatement un médecin. 309410 ADVERTÊNCIA Perigo de incêndio e explosão: os solventes e os vapores da pintura poderão explodir ou incendiar.
- Page 3 Pressure Control Controle da pressão Système de contrôle de la pression Dispositivo de control de la presión Drain Valve Válvula de drenagem Vidange Válvula de vaciado On/Off Switch Interruptor de ligar e desligar Interrupteur marche/arrêt Interruptor de encendido/apagado ti1854a 309410...
-
Page 4: S Setup
Setup Change Engine to Motor 1. Disconnect engine power cord. 2. Release tension bar. Release 3. Remove engine; tilt and slide back. 4. Install motor; drop in and push forward. 309410... - Page 5 Setup Change Engine to Motor 5. Look through side vent holes and ensure drive belt is in motor pulley. 6. Secure motor with tension bar. Engage 7. Plug in pressure control power cord. 309410...
- Page 6 309410 Setup 1. Connect appropriate Graco high-pressure hose to sprayer. Tighten securely. Note: Remove second gun port cap for multiple guns and repeat steps 1 – 4, 7, 8, 10 2. Connect other end of hose to gun. 3. Tighten securely.
- Page 7 Do this each time you spray and store. 7. Check engine oil level. Add SAE 10W–30 (summer) or 5W–20 (winter), if necessary. 8. Fill fuel tank. 9. Ground sprayer with grounding clamp. Setup Approximate Fill Level (cold) 309410...
-
Page 8: S Startup
PAINT FLUSH 309410 Startup 1. Place suction tube and drain tube in grounded metal pail partially filled with flushing fluid. Attach ground wire to pail and to true earth ground. 2. Turn prime valve down. Turn pressure control to lowest pressure. - Page 9 Set throttle to fast d. Set engine switch ON e. Pull starter cord f. After engine starts, move choke to open g. Set throttle to desired setting – Digital display is functional after engine starts – Start motor Startup 309410...
- Page 10 OFF immediately. Do Pressure Relief in Cleanup, 1. – 3. on page 19. Tighten leaky fittings. Repeat Startup, 1. – 5. If no leaks, continue to trigger gun until system is thoroughly flushed. Proceed to 6. 309410 Startup 5. Set pump switch ON.
- Page 11 Assemble tip and guard, page 11. SwitchTip and Guard Assembly 1. Engage trigger safety. 2. Insert SwitchTipt. Insert seat and OneSealt. 3. Screw assembly onto gun. Hand tighten. Startup SwitchTip PAINT FLUSH safety ON ti2871a seat OneSeal 309410...
-
Page 12: S Digital Tracking Systemt (Dts)
Operation Main Menu PAINT FLUSH 309410 Digital Tracking Systemt (DTS) Close cover when spraying to protect from overspray 1. Do Startup steps 1. – 3. 2. Start engine or motor, page 9. Sprayer Model momentarily displays, e. g., C5900 = GMax 5900 Convertible Pressure display appears. - Page 13 Clean Timer operation (Manual 309278). Note: If the pump is started in the timer mode, the timer counts down to zero and shuts the pump OFF. Use for flushing only. 6. Short press DTS button to return to Pressure. 309410...
- Page 14 309410 WatchDogt Pump Protection System Pump stops automatically when material pail is empty. To Activate: 1. Do Startup. Increase pressure to more than 2000 psi (140 bar, 14 MPa). Note: Instructions to automatically activate the WatchDog pump protection system every time you spray are on page 16.
- Page 15 Pressure must be at zero. 2. Start engine or motor, page 9. Pressure display appears. 3. Simultaneously press DTS button and set pump on/off switch on. Sprayer model momentarily displays, e.g., C5900 = GMAX 5900 Convert- ible. Resettable Hour Meter appears. PAINT FLUSH 309410...
- Page 16 Secondary Menu – Stored Data and WatchDog Pump Protection Modes 309410 4. Press and hold to reset to zero, or 5. Short press DTS button to move to Lifetime Hour Meter. 6. Short press DTS button to move to TOTAL Gallons (all pressures).
- Page 17 AUTO mode. In AUTO mode, WatchDog pump protection is active once pressure is over 1500 psi (103 Bar, 10.3 MPa) 11. Short press to return to step 3. 12. Turn pump switch OFF at any time to exit stored data mode. 309410...
- Page 18 309410 Spray Test Pattern 1. Trigger gun and spray test pattern. Slowly adjust pressure to eliminate heavy edges. Use smaller tip size if pressure adjustment can not eliminate heavy edges. 2. Hold gun perpendicular, 10–12 in. (25–30 cm) from surface. Spray back and forth.
-
Page 19: S Cleanup
Pressure Relief 1. Set pump switch OFF. Turn engine or motor OFF. Pressure Relief 2. Turn pressure to lowest setting. Trigger gun to relieve pressure. Pressure Relief 3. Turn prime valve down. 4. Remove guard and SwitchTip. Cleanup PAINT 309410... - Page 20 FLUSH PAINT FLUSH 309410 5. Unscrew bowl, remove filter. As- semble without filter. Clean filter. 6. Clean filter, guard and SwitchTip in flushing fluid. 7. Remove siphon tube set from paint and place in flushing fluid. Use water for water base paint and mineral spirits for oil base paint.
- Page 21 11. Move gun to flushing pail, hold gun against pail, trigger gun to thoroughly flush system. Release trigger and put trigger safety ON. 12. Turn prime valve down and allow flushing fluid to circulate for approxi- mately 20 seconds to clean drain tube. PAINT FLUSH 20 SEC 309410...
- Page 22 Pump Armor and leave this protective coating in the sprayer to help prevent freezing or corrosion and increase sprayer life. FLUSH 309410 13. Raise siphon tube above flushing fluid and run sprayer for 15 to 30 seconds to drain fluid.
-
Page 23: S Error Codes
DTS Error Codes 309409 Reference Repair Manual 309409 or 309411 or call your distributor for service Service 309410... -
Page 24: Graco Warranty
Graco reserves the right to make changes at any time without notice. Sales Offices: Minneapolis, Detroit International Offices: Belgium, Korea, Hong Kong, Japan GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 http://www.graco.com PRINTED IN U.S.A. 309410 1/2002, Revised 3/2003 309410...