Table of Contents
Advertisement
T
O PREVENT THE RISK OF PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH,
DO NOT STORE COMBUSTIBLE MATERIALS OR USE GASOLINE OR OTHER
FLAMMABLE LIQUIDS OR VAPORS IN THE VICINITY OF THIS APPLIANCE.
HIGH VOLTAGE!
I
NSTALLATION
AND
REPAIR
OF
ONLY
PERFORMED
BY
INDIVIDUALS
)
MINIMUM
THE
REQUIREMENTS
T
"
ECHNICIAN
AS
SPECIFIED
BY
H
,
R
EATING
AND
EFRIGERATION
A
TTEMPTING
TO
INSTALL
OR
REPAIR
SUCH
BACKGROUND
MAY
RESULT
.
PERSONAL
INJURY
OR
DEATH
GENERAL INFORMATION
T
O PREVENT PROPERTY DAMAGE, PERSONAL INJURY OR DEATH, DUE TO FIRE,
EXPLOSIONS, SMOKE, SOOT, CONDENSATION, ELECTRIC SHOCK OR CARBON
MONOXIDE, THIS UNIT MUST BE PROPERLY INSTALLED, REPAIRED, OPERATED,
AND MAINTAINED.
This unit is approved for outdoor installation ONLY. To
assure that your unit operates safely and efficiently, it must
be installed, operated, and maintained in accordance with
these installation and operating instructions, all local building
codes and ordinances.
EPA R
EGULATIONS
I
: T
U
MPORTANT
HE
NITED
A
(EPA)
GENCY
HAS ISSUED VARIOUS REGULATIONS REGARDING
THE INTRODUCTION AND DISPOSAL OF REFRIGERANTS IN THIS UNIT
F
AILURE TO FOLLOW THESE REGULATIONS MAY HARM THE
ENVIRONMENT AND CAN LEAD TO THE IMPOSITION OF SUBSTANTIAL
. B
FINES
ECAUSE REGULATIONS MAY VARY DUE TO PASSAGE OF NEW
,
LAWS
WE SUGGEST A CERTIFIED TECHNICIAN PERFORM ANY WORK
. S
DONE ON THIS UNIT
HOULD YOU HAVE ANY QUESTIONS PLEASE
CONTACT THE LOCAL OFFICE OF THE
N
C
ATIONAL
ODES
This product is designed and manufactured to permit instal-
lation in accordance with National Codes. It is the installer's
responsibility to install the product in accordance with Na-
tional Codes and/or prevailing local codes and regulations.
The heating and cooling capacities of the unit should be
greater than or equal to the design heating and cooling loads
of the area to be conditioned. The loads should be calculated
by an approved method or in accordance with ASHRAE Guide
or Manual J - Load Calculations published by the Air Condi-
tioning Contractors of America.
WARNING
WARNING
THIS
UNIT
SHOULD
BE
(
MEETING
AT
A
"E
L
OF
AN
NTRY
EVEL
A
C
,
THE
IR
ONDITIONING
I
(AHRI).
NSTITUTE
THIS
UNIT
WITHOUT
,
IN
PRODUCT
DAMAGE
WARNING
S
E
P
TATES
NVIRONMENTAL
ROTECTION
EPA.
American National Standards Institute
System design and installation should also, where applicable,
follow information presented in accepted industry guides such
as the ASHRAE Handbooks. The manufacturer assumes no
responsibility for equipment installed in violation of any code
or regulation. The mechanical installation of the packaged
roof top units consists of making final connections between
the unit and building services; supply and return duct con-
nections; and drain connections (if required). The internal
systems of the unit are completely factory-installed and tested
prior to shipment.
Units are generally installed on a steel roof mounting curb
assembly which has been shipped to the job site for installa-
tion on the roof structure prior to the arrival of the unit. The
model number shown on the unit's identification plate identi-
fies the various components of the unit such as refrigeration
tonnage, heating input and voltage.
Carefully inspect the unit for damage. Any bolts or screws
which may have loosened in transit must be re-tightened. In
the event of damage, the receiver should:
1. Make notation on delivery receipt of any visible
damage to shipment or container.
2. Notify carrier promptly and request an inspection.
3. In case of concealed damage, carrier should be
notified as soon as possible-preferably within 5 days.
4. File the claim with the following supporting documents:
a. Original Bill of Lading, certified copy, or indemnity
bond.
b. Original paid freight bill or indemnity in lieu thereof.
c. Original invoice or certified copy thereof, showing
trade and other discounts or reductions.
.
d. Copy of the inspection report issued by carrier
representative at the time damage is reported to the
carrier. The carrier is responsible for making prompt
inspection of damage and for a thorough
investigation of each claim. The distributor or
manufacturer will not accept claims from dealers for
transportation damage.
NOTE: When inspecting the unit for transportation damage,
remove all packaging materials. Recycle or dispose of the
packaging material according to local codes.
P
-I
C
RE
NSTALLATION
Carefully read all instructions for the installation prior to in-
stalling unit. Ensure each step or procedure is understood
and any special considerations are taken into account be-
fore starting installation. Assemble all tools, hardware and
supplies needed to complete the installation. Some items may
need to be purchased locally.
3
Obtain from:
1430 Broadway
New York, NY 10018
HECKS
Advertisement
Table of Contents
