Advertisement
C
C
oolinG
aPaCity
34,600 - 71,000 BtU/
h
C
eatinG
aPaCity
36,800 - 110,400 BtU/
Standard Features
• R-410A chlorine-free refrigerant
• TuffTube™ tubular heat exchanger
• High-efficiency scroll compressor
• HIgh- and low-pressure switches
• Copper tube / aluminum fin coils
• Contactor with lugs
• High-capacity, steel-cased filter drier
• 24-volt terminal strip
• Convertible
• Easy to service
• Built-in filter rack with standard 2" filters
• Bottom utility entry
• Complies with California NOx emissions standards
• AHRI Certified; ETL Listed
Cabinet Features
• Heavy-gauge, galvanized-steel cabinet with
UV-resistant powder-paint finish
• Full Perimeter Rail
* Complete warranty details available from your local dealer or at www.goodmanmfg.com.
SS-CPG36-72
:
h
:
h
www.goodmanmfg.com
CPG C
3-
P
aCkaGed
13 seer /
80% aFUe
Contents
Nomenclature .................................................................... 2
Product Specifications ....................................................... 3
Airflow Data .....................................................................10
Expanded Cooling Data ................................................... 17
Dimensions ......................................................................25
Wiring Diagrams ............................................................. 29
Accessories .......................................................................39
ommerCial
6-t
to
on
G
/e
U
as
leCtriC
nits
11.3 eer
UP to
3/12
Supersedes 11/11
Advertisement
Related Manuals for Goodman SS-CPG36-72
Summary of Contents for Goodman SS-CPG36-72
-
Page 1: Table Of Contents
• 24-volt terminal strip • Convertible • Easy to service • Built-in filter rack with standard 2” filters • Bottom utility entry • Complies with California NOx emissions standards • AHRI Certified; ETL Listed Cabinet Features • Heavy-gauge, galvanized-steel cabinet with UV-resistant powder-paint finish • Full Perimeter Rail * Complete warranty details available from your local dealer or at www.goodmanmfg.com. SS-CPG36-72 CPG C aCkaGed 13 seer / Contents Nomenclature ... 2 Product Specifications ... 3 Airflow Data ...10 Expanded Cooling Data ... 17 Dimensions ...25 Wiring Diagrams ... 29 Accessories ...39 www.goodmanmfg.com... -
Page 2: Nomenclature
Stainless-‐Steel H eat E xchanger Factory-‐Installed O p7ons No O pCons Downflow E conomizer Supply F an/Drive T ype/Motors Belt D rive Direct D rive High-‐StaCc B elt D rive ( Factory-‐Installed) SS-CPG36-72... -
Page 3: Product Specifications
¹ Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes. ² May use fuses or HACR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. SS-CPG36-72 CPG036 CPG036... - Page 4 1 / 22 2 / 16 1 / Single 1 / Single Scroll Scroll 5.8 / 38.0 3.8 / 36.5 460-3-60 575-3-60 1 / 1.9 1 / 1.9 ¼ / 0.8 ¼ / 0.8 8.47 6.68 1.125 1.125 ½” ½” SS-CPG36-72...
- Page 5 Total Unit Amps Min. Circuit Ampacity¹ Max. Overcurrent Protection (amps)² Power Supply Conduit Hole Low-Voltage Conduit Hole Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes. ² May use fuses or HACR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. SS-CPG36-72 CPG048 CPG048 0901D***B* 0903D***B* 45,500 45,500 35,000 35,000 13.0 / 11.3 13.0 / 11.3...
- Page 6 ¼ - 1,075 22 / 4 22 / 4 3,800 3,800 17.0 17.0 1 / 24 1 / 24 1 / Single 1 / Single Scroll Scroll 6.1 / 41 4.4 / 33 460-3-60 575-3-60 0.80 0.60 1.125 1.125 ½” ½” SS-CPG36-72...
- Page 7 Outdoor Fan HP / FLA Min. Circuit Ampacity¹ Max. Overcurrent Protection (amps)² Power Supply Conduit Hole Low-Voltage Conduit Hole Operating Weight (lbs) Ship Weight (lbs) ¹ Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes. ² May use fuses or HACR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. SS-CPG36-72 CPG060 CPG060 0901D***B* 0903D***B* 59,500 59,500 43,200 43,200 13 / 11.0 13 / 11.0...
- Page 8 2 / 18 5/16 - Copper 5/16 - Copper 1 / Single 1 / Single Scroll Scroll 7.8 / 52 5.7 / 38.9 460-3-60 575-3-60 1.0 / 1.9 1.5 / 2.3 ¼ / 0.8 ¼ / 0.6 1.125 1.125 ½” ½" SS-CPG36-72...
- Page 9 ¹ Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes. ² May use fuses or HACR-type circuit breakers of the same size as noted. Note: Always check the S&R plate for electrical data on the unit being installed. SS-CPG36-72 CPG072 CPG072...
-
Page 10: Airflow Data
High 1012 1098 0.70 1034 0.80 1067 www.goodmanmfg.com — d ireCt rive Speed Amps Watts 1.68 1.63 1.59 1.55 1.50 1.45 2.11 2.06 2.02 1.95 1.90 1.82 1.74 1012 2.37 2.31 2.25 High 2.17 1000 2.09 1023 1.99 1045 SS-CPG36-72... - Page 11 1307 1307 0.58 1002 1002 0.48 0.38 Note: Tables represent dry coil without filter; to compensate for filter, add 0.08” to measured E.S.P. SCFM correction for wet coil = 4%. SS-CPG36-72 — h tandard rive orizontal Turns Open 1628 0.41 1396 0.32...
- Page 12 1954 1853 1740 High 1626 1510 1385 www.goodmanmfg.com — d ireCt rive Speed Amps Watts 2.60 2.49 2.38 2.27 2.16 3.14 2.81 2.67 2.54 2.38 2.28 1019 2.11 1047 3.43 3.27 3.12 High 2.96 1002 2.85 1019 2.71 1036 SS-CPG36-72...
- Page 13 1611 1616 0.80 1298 1316 0.66 1007 Note: Tables represent dry coil without filter; to compensate for filter, add 0.08” to measured E.S.P. SCFM correction for wet coil = 4%. SS-CPG36-72 — h tandard rive orizontal Turns Open 2002 0.65 1708 0.49...
- Page 14 4.58 4.69 4.80 4.87 4.97 1008 5.05 1039 5.14 5.26 5.32 5.47 1001 5.54 1021 5.61 1041 5.73 1072 5.81 1093 5.84 1122 5.87 5.96 6.06 1012 6.15 1039 6.21 1056 6.32 1084 6.28 1102 6.22 1122 6.04 1127 SS-CPG36-72...
- Page 15 1610 1587 0.67 1384 (“ H 2277 2304 1.39 2089 2104 1.26 1893 1912 1.13 1690 1720 1.00 Note: Tables represent dry coil without filter; to compensate for filter, add 0.08” to measured E.S.P. SCFM correction for wet coil = 4%. SS-CPG36-72 — h tandard rive orizontal Turns Open 2460 0.96 2251 0.80 1.00 2206 0.84 1982 0.68 0.89 1943 0.72 1701 0.55...
- Page 16 0.68 2159 0.75 1938 0.59 1898 0.64 4 Turns 5 Turns 2677 1.29 2486 1.07 2529 1.20 2263 0.94 2246 1.02 1972 0.79 1970 0.87 4 Turns 5 Turns 2407 1.15 2250 0.96 2226 1.04 2011 0.84 2012 0.92 SS-CPG36-72...
-
Page 17: Expanded Cooling Data
PeCiFiCations — CPG036B xPanded oolinG SS-CPG36-72 www.goodmanmfg.com... - Page 18 PeCiFiCations — CPG036B ( xPanded oolinG Cont www.goodmanmfg.com SS-CPG36-72...
- Page 19 PeCiFiCations — CPG048B xPanded oolinG SS-CPG36-72 www.goodmanmfg.com...
- Page 20 PeCiFiCations — CPG048B ( xPanded oolinG Cont www.goodmanmfg.com SS-CPG36-72...
- Page 21 PeCiFiCations — CPG060B xPanded oolinG SS-CPG36-72 www.goodmanmfg.com...
- Page 22 PeCiFiCations — CPG060B ( xPanded oolinG Cont www.goodmanmfg.com SS-CPG36-72...
- Page 23 PeCiFiCations — CPG072B xPanded oolinG SS-CPG36-72 www.goodmanmfg.com...
- Page 24 PeCiFiCations — CPG072B ( xPanded oolinG Cont www.goodmanmfg.com SS-CPG36-72...
-
Page 25: Dimensions
For horizontal discharge, remove the supply and return duct covers and place them over the vertical discharge return and supply openings. Install with insulation facing up, using the longer screws provided in the literature package. SS-CPG36-72 47 1/2” 47¹/₂” 74¹/₁₆” 73 13/16” 11”... - Page 26 PeCiFiCations learanCes Maintain an adequate clearance around the unit for safety, service, maintenance, and proper unit operation. Leave a total clearance of 75” on the main control panel side of the unit for possible removal of fan shaft, coil, electric heat, and gas furnace. Leave a clearance of 48” on all other sides of the unit for possible compressor removal or service access, and to ensure proper ventilation and condenser airflow. Do not install the unit beneath any obstruction. Install the unit away from all building exhausts to inhibit ingestion of exhaust air into the unit’s fresh-air intake. leCtriCal ntranCe oCations High-Voltage Entrance (Remove Plug) Low-Voltage Entrance 12 ” 30¼” Power Thru the Curb 47½” www.goodmanmfg.com 3½” Dia. 4½” 7½” SS-CPG36-72...
- Page 27 Refer to the Roof Curb Installation Instructions for proper curb installation. Curbing must be installed in compliance with the National Roofing Contractors Association Manual. Lower unit carefully onto roof mounting curb. While rigging the unit, the center of gravity will cause the condenser end to be lower than the supply air end. Bring condenser end of unit into alignment with the curb. With condenser end of the unit resting on curb member and using curb as a fulcrum, lower opposite end of the unit until entire unit is seated on the curb. When a rectangular cantilever curb is used, take care to center the unit. Check for proper alignment and orientation of supply and return openings with duct. 30” Condenser Coil Evaporator Coil Compressor 37” SS-CPG36-72 & C orner enter ravity oCations Unit Weights Corner Weight (A) Return Corner Weight (B) Corner Weight (C) Corner Weight (D) Unit Shipping Weight Supply Unit Operating Weight Note: Weights are calculated without accessories installed.
- Page 28 Association. Proper unit installation requires that the roof curb be firmly and permanently attached to the roof structure. Check for adequate fastening method prior to setting the unit on the curb. Full perimeter roof curbs are available from the factory and are shipped unassembled. The installing contractor is responsible for field assembly, squaring, leveling, and mounting on the roof structure. All required hardware necessary for the assembly of the sheet metal curb is included in the curb accessory package. • Determine sufficient structural support before locating and mounting the curb and package unit. • Duct-work must be constructed using industry guidelines. The duct-work must be placed into the roof curb before mounting the package unit. Our full perimeter curbs include duct connection frames to be assembled with the curb. Cantilevered-type curbs are not available from the factory. • Contractor furnishes curb insulation, cant strips, flashing, and general roofing material. • Support curbs on parallel sides with roof members. To prevent damage to the unit, the roof members cannot penetrate supply and return duct openings. Note: The unit and curb accessories are designed to allow vertical duct installation before unit placement. Duct installation after unit placement is not recommended. See the manual shipped with the roof curb for assembly and installation instructions. 3-d v 70¾ 14 x 20 Supply Opening 31⅝ x 14 Return Opening Insulated Panels 40¼ ¾ 1⅜ www.goodmanmfg.com SS-CPG36-72...
-
Page 29: Wiring Diagrams
OPEN LIMIT SWITCH MAIN LIMIT OPEN BAD SWITCH 5 BLINKS FALSE FLAME SENSED STICKING GAS VALVE 6 BLINKS COMPRESSOR 3 MIN. COMP. OUTPUT DELAY ANTI-CYCLE TIMER SS-CPG36-72 inGle hase ireCt rive 208-240/1/60 SEE NOTE 5 NOTE 2 SMOKE/FIRE DETECTOR REPLACE... - Page 30 SEE UNIT RATING PLATE FOR TYPE AND SIZE OF OVERCURRENT PROTECTION. 208-240/1/60 0140L00506 REV A www.goodmanmfg.com YL RD YL/PK YL/PK BL/PK FACTORY WIRING LINE VOLTAGE LOW VOLTAGE OPTIONAL HIGH VOLTAGE FIELD WIRING HIGH VOLTAGE LOW VOLTAGE STAT STAT STAT SS-CPG36-72...
- Page 31 MAIN LIMIT OPEN 4 BLINKS BAD SWITCH 5 BLINKS FALSE FLAME SENSED STICKING GAS VALVE 6 BLINKS COMPRESSOR 3 MIN. COMP. OUTPUT DELAY ANTI-CYCLE TIMER SS-CPG36-72 inGle hase ireCt rive POWER SUPPLY 240/1/60 SEE NOTE 6 NOTE 2 FUSE SMOKE/FIRE...
- Page 32 LOW VOLTAGE WIRE CODE BLACK BLUE BROWN GREEN ORANGE PINK PURPLE WHITE YELLOW BL/PK BLUE WITH PINK STRIP YL/PK YELLOW WITH PINK STRIP THERMOSTAT FIELD WIRING NO ECONOMIZER Y/Y2 STAT WITH ECONOMIZER OPTION Y/Y2 STAT 2 STAGE COOLING Y/Y2 STAT SS-CPG36-72...
- Page 33 OPEN LIMIT SWITCH MAIN LIMIT OPEN BAD SWITCH 5 BLINKS FALSE FLAME SENSED STICKING GAS VALVE 6 BLINKS COMPRESSOR 3 MIN. COMP. OUTPUT DELAY ANTI-CYCLE TIMER SS-CPG36-72 hree hase ireCt rive POWERSUPPLY NOTE 2 FUSE Y1 W1 SEE NOTE 8 GREEN JUMPER...
- Page 34 LOW VOLTAGE WIRE CODE BLACK BLUE BROWN GREEN ORANGE PINK PURPLE WHITE YELLOW BL/PK BLUE WITH PINK STRIP YL/PK YELLOW WITH PINK STRIP THERMOSTAT FIELD WIRING NO ECONOMIZER Y/Y2 STAT WITH ECONOMIZER OPTION Y/Y2 STAT 2 STAGE COOLING Y/Y2 STAT SS-CPG36-72...
- Page 35 MAIN LIMIT OPEN 4 BLINKS BAD SWITCH 5 BLINKS FALSE FLAME SENSED STICKING GAS VALVE 6 BLINKS COMPRESSOR 3 MIN. COMP. OUTPUT DELAY ANTI-CYCLE TIMER SS-CPG36-72 460/575 SMOKE/FIRE DETECTOR REPLACES JUMPER WIRE ECON NOTE 3 NOTE 3 W2 G TO THERMOSTAT...
- Page 36 LOW VOLTAGE WIRE CODE BLACK BLUE BROWN GREEN ORANGE PINK PURPLE WHITE YELLOW BL/PK BLUE WITH PINK STRIP YL/PK YELLOW WITH PINK STRIP THERMOSTAT FIELD WIRING NO ECONOMIZER Y/Y2 STAT WITH ECONOMIZER OPTION Y/Y2 STAT 2 STAGE COOLING Y/Y2 STAT SS-CPG36-72...
- Page 37 MAIN LIMIT OPEN 4 BLINKS BAD SWITCH 5 BLINKS FALSE FLAME SENSED STICKING GAS VALVE 6 BLINKS COMPRESSOR 3 MIN. COMP. OUTPUT DELAY ANTI-CYCLE TIMER SS-CPG36-72 — CPG072*4B/7B (460v/ 575v B 460/575 SMOKE/FIRE DETECTOR REPLACES JUMPER WIRE ECON NOTE 3 NOTE 3...
- Page 38 LOW VOLTAGE WIRE CODE BLACK BLUE BROWN GREEN ORANGE PINK PURPLE WHITE YELLOW BL/PK BLUE WITH PINK STRIP YL/PK YELLOW WITH PINK STRIP THERMOSTAT FIELD WIRING NO ECONOMIZER Y/Y2 STAT WITH ECONOMIZER OPTION Y/Y2 STAT 2 STAGE COOLING Y/Y2 STAT SS-CPG36-72...
-
Page 39: Accessories
LP Conversion Kit LPT-00A LP Conversion Kit (CPG036045 only) PE36722B Power Exhaust 208/230 Volt PE36724B Power Exhaust 460 Volt Stainless-Steel Heat Exchanger (Type 409) UltraGold Condenser Coil SS-CPG36-72 Fits Description Model Sizes 3-6 tons 3-6 tons 3-6 tons 3-6 tons 3 tons... - Page 40 PeCiFiCations otes Goodman Manufacturing Company, L.P., reserves the right to discontinue, or change at any time, specifications or designs without notice or without incurring obligations. © 2012 • Goodman Manufacturing Company, L.P. • Houston, Texas • Printed in the USA. www.goodmanmfg.com SS-CPG36-72...