JVC GY-DV5100 Instructions Manual page 16

2. CONTROLS, INDICATORS AND CONNECTORS
2-2 Right Side Section (Cont'd)
3200K
1
2 5600K 1 8 / ND
.3 5600K
.4 5600K 1 64 / ND
STATUS
SHUTTER
MENU
AUTO IRIS FULL AUTO BLACK LOLUX
MODE
BACK L STRETCH
VTR
NORMAL NORMAL
SPOT L COMPRESS
CAM
POWER VTR
ON OFF
View with cover open.
AUDIO
CH-1 CH-2
LEVEL
FRONT MIC +48V
OFF
ON
!1
0
[CH-1/CH-2 AUDIO IN] CH-1/CH-2 audio input
selector switch
This switch is used to select the input sound of the CH1 or
CH2 audio channel. It is selected for each of the CH1 and
CH2 channels.
FRONT : The sound from the FRONT MIC IN connector
on the front side section is input.
REAR : The sound from the REAR AUDIO IN connector
on the rear side section is input.
!
[FRONT MIC +48V] Front microphone power
supply selector switch
This is set in accordance with the camera microphone con-
nected to the FRONT MIC IN connector.
ON : Set to this position when the included microphone
or another requiring +48 V power supply (phantom
microphone) is connected.
OFF : Set to this position when connecting a microphone
that does not require +48 V power supply.
@
[CH-1/CH-2 REAR AUDIO IN] CH-1/CH-2 Rear
audio input signal selector switch
This switch is used to select the input sound signal from
the REAR AUDIO IN connector.
LINE : Set to this position when connected to audio
equipment, etc. The reference input level is +4 dBs.
MIC : Set to this position when the microphone is
connected. The reference input level is -60 dBs.
+48V : Set to this position when a microphone requiring
+48 V power supply (phantom microphone, etc.) is
connected. This connector supplies +48 V DC
current.
CAUTION:
When connecting a component that does not require
+48 V power supply, make sure that the switch is not
set to +48V before the component is connected.
#
[MONITOR SELECT] Audio monitor selector
switch
This switch is used to select the monitor sound output and
playback sound output from the monitoring speaker
page 15 or the PHONES
E-16
LCD BRIGHT DISPLAY
AUDIO
PULL
LEVEL
OPEN
FRONT
REAR
CH-1 CH-2
CH-1 CH-2
AUDIO INPUT
AUDIO SELECT
CH-1 CH-2
AUTO
MANUAL
!0
!3
LCD BRIGHT DISPLAY
MONITOR
SELECT !4
COUNTER
CH-1
MIX FRONT TC
CH-2 REAR
UB
CH-1 CH-2
AUDIO IN
REAR
AUDIO SELECT
AUDIO IN !5
TC GENE.
CH-1 CH-2
CH-1 CH-2
AUTO PRST FREE
LINE
MIC MANUAL REC
+48V
REGEN
!2
5
jack on page 19.
CH-1 : The CH1 channel audio is output.
MIX : CH1 and CH2 channel audio are output mixed.
When this setting is selected, the menu screen can
be used to select whether the mixed sound or stereo
sound should be output via the PHONES jack.
(AUDIO MONITOR item on the AUDIO menu
screen)
When AUDIO MONITOR in the AUDIO menu
screen is set to "STEREO", only the audio of CH-1
is output from the monitoring speaker.
CH-2 : The CH2 channel audio is output.
☞ See "Outputting CH-3, CH-4 Channel Audio" on page 64.
☞ See "AUDIO Menu Screen" on page 79.
CAUTION:
Make sure to move switches all the way. Do not leave a
switch stopped in a midway position. Noise will be
generated and operation irregularities will occur.
$
[COUNTER] Counter display switch
Selects the contents displayed on the TC counter of the
LCD monitor or in the viewfinder. (This switch works when
the TC/UB item on the LCD/VF (2/2) menu screen is set to
ON.)
TC : Set to this position to display time code values.
UB : Set to this position to display the user's bits values.
%
[TC GENE.] Time code generator setting switch
Switch for setting the time code generator to preset mode
or regeneration mode. It is also used to select the time code
run mode when the preset mode is selected.
PRST-FREE
* If this setting is used when recording scenes one after
another, the time codes become discontinuous at the
transition points between scenes.
PRST-REC
REGEN : Regeneration mode, in which the unit reads
existing time codes on the tape and records time
codes in continuation of the existing ones. Set to
this position when you want to add additional time
codes to time codes already recorded on the tape.
MEMO:
Preset of time code and user's bits is performed on the
TC/UB/CLOCK menu.
☞ See "TIME CODE OPERATION" on page 67.
1
on
☞ See "TC/UB/CLOCK Menu Screen" on page 83.
: The preset mode is selected, and the time
code run mode becomes the FREE run
mode.
Set to this position to record with the time
code or user's bits set anew (preset). In
this setting, the time code always
operates in the run mode.
: The preset mode is selected, and the time
code run mode becomes the REC run
mode.
Set to this position to record with the time
code or user's bits set anew (preset). The
time code operates in the run mode
during recording only. If this setting is
used when recording scenes one after
another, the time codes are recorded as
continuous time codes.