Denon AVR-4308 Owner's Manual page 95

GAudioH
Symptom Cause
No sound is • Monaural source (monitor, AM
produced from station, etc.) being played in
center speaker. "STANDARD" mode.
No sound • The surround mode is set to
is produced "STEREO" , "DIRECT" or "PURE
from surround DIRECT" .
speakers. • The surround speaker's power
amplifier is assigned to a different
channel.
No sound is • Surround back speaker setting is
produced from set to "None" .
surround back • Surround mode not set to a mode
speaker. for 6.1- or 7 .1-channel playback.
• The surround back speaker's
power amplifier is assigned to a
different channel.
No sound is • Subwoofer's power not turned
produced from on.
subwoofer. • The "Subwoofer" setting at
"Speaker configuration" is set to
"No" .
• The subwoofer is not properly
connected.
• The subwoofer's volume
turned off.
No test tones are • Surround mode not set to
produced when "STANDARD" .
main remote
control unit's TEST
TONE button is
pressed.
DTS sound is not • DVD player's audio output setting
output. is not set to bitstream.
• DVD player is not compatible
with DTS sound playback.
• The AVR-4308's "Decode Mode"
setting is set to "PCM" .
HDMI audio • The "Manual Setup" – "HDMI
signals are not Setup" – "Audio" setting is set to
output from "TV" .
speakers.
Countermeasure Page
• The mode is set to something 43, 44
other than "STANDARD" .
• Set to a surround playback 43, 44
mode.
• Check the setting and change it 36
as necessary.
• Set to something other than 29
"None" .
• Select a surround playback 43, 44
mode.
• Check the setting and change it 36
as necessary.
• Turn on the subwoofer's power. –
• Set to "Yes" . 29
• Check the connections. 10
is • Adjust the subwoofer's volume 63
to an appropriate level.
• Set to the "STANDARD" mode. 43
• Set the DVD player. For details, –
refer to the DVD player's
operating instructions.
• Use a DTS-compatible player. –
• Set to the "Auto" or "DTS" 40
mode.
• Set to "Amp" . 31
Symptom Cause
No sound is • The "Manual Setup" – "HDMI
output from Setup" – "Audio" setting is set to
the monitor "Amp" .
connected
with HDMI
connections.
GVideoH
Symptom Cause
The on-screen • The format of the GUI and TV
display does not (PAL or NTSC) do not match.
appear.
No picture • The connections between the
appears. AVR-4308 and monitor
faulty.
• The monitor's input setting is
wrong.
• PURE DIRECT mode is set.
• The player is connected using the
component input connectors, the
monitor is connected using the
video (yellow) or S-Video output
connectors.
No picture • The connections to the HDMI
appears connectors are faulty.
with HDMI • HDMI input setting is improper.
connections. • The monitor is not compatible
with copyright
(HDCP).
• The HDMI format of the player
and monitor do not match.
Picture cannot be • Input source does not match
recorded. recorder's video connection
connector (video or S-Video).
DVDs cannot be
copied on a VCR.
–
Countermeasure
• Set to "TV" .
Countermeasure
• Match the format of the GUI and
TV.
• Check the connections.
are
• Set properly.
• Cancel the PURE DIRECT mode.
• High definition (1080i/720p) and
progressive (480p/576p) video
signals are not down-converted.
Set the player to interlace
(480i/576i) signals.
• Check the connections.
• Check the HDMI input setting.
• Connect a monitor that is
protection compatible with copyright
protection (HDCP).
• Match the HDMI format of the
player and monitor.
• The video conversion function
does not work for the REC
OUT connectors. Match the
input source and recorder
connections.
• This is not a malfunction. Most
movie software includes copy
prevention signals and cannot be
copied.
ENGLISH
Page
31
Page
36
12 ~ 23
–
43, 44
–
12
41
12
12
16
–