Roland JUNO-Di Editor Owner's Manual page 92

Effects List
Reverb Parameters
These settings allow you to select the desired type of reverb, and its characteristics.
Parameter Value
OFF,
REVERB,
Reverb SRV ROOM,
Type SRV HALL,
SRV PLATE,
GM2 REVERB
Reverb
0–127
Level
REVERB
ROOM1,
ROOM2,
STAGE1,
Type
STAGE2, HALL1,
HALL2, DELAY,
PAN-DELAY
Time 0–127
200–8000 Hz,
HF Damp
BYPASS
Delay
0–127
Feedback
SRV ROOM
SRV HALL
SRV PLATE
Pre
0.0–100 msec
Delay
Time
0–127
Size 1–8
160–12500 Hz,
High Cut
BYPASS
Density 0–127
Diffusion 0–127
LF Damp
50–4000 Hz
Freq
LF Damp
-36–0 dB
Gain
HF Damp
4000–12500 Hz
Freq
HF Damp
-36–0 dB
Gain
92
Explanation
Type of reverb
OFF: Reverb is not used.
REVERB: Normal reverb
SRV ROOM: This simulates typical room
acoustic reflections.
SRV HALL: This simulates typical concert
hall acoustic reflections.
SRV PLATE: This simulates a reverb plate, a
popular type of artificial reverb unit that
derives its sound from the vibration of a
metallic plate.
GM2 REVERB: GM2 Reverb
Volume of the reverb sound
Type of reverb/delay
ROOM1: short reverb with high density
ROOM2: short reverb with low density
STAGE1: reverb with greater late
reverberation
STAGE2: reverb with strong early reflections
HALL1: very clear-sounding reverb
HALL2: rich reverb
DELAY: conventional delay effect
PAN-DELAY: delay effect with echoes that
pan left and right
Time length of reverberation
(Type: ROOM1–HALL2)
Delay time
(Type: DELAY, PAN-DELAY)
Adjusts the frequency above which the
high-frequency content of the reverb sound will
be cut, or "damped." If you do not want to cut the
high frequencies, set this parameter to BYPASS.
Adjusts the amount of delay feedback when
the Type setting is DELAY or PAN-DELAY.
Amount of delay sound returned to the input
(this setting is valid only if Type is DELAY or
PAN-DELAY)
Adjusts the delay time from the direct sound until
the reverb sound is heard.
Time length of reverberation
Size of the simulated room or hall
Adjusts the frequency above which the
high-frequency content of the reverb will be
reduced. If you do not want to reduce the high
frequencies, set this parameter to BYPASS.
Density of reverb
Adjusts the change in the density of the reverb over
time. The higher the value, the more the density
increases with time. (The effect of this setting is most
pronounced with long reverb times.)
Adjusts the frequency below which the low-
frequency content of the reverb sound will be
reduced, or "damped."
Adjusts the amount of damping applied to the
frequency range selected with LF Damp. With
a setting of "0," there will be no reduction of
the reverb's low-frequency content.
Adjusts the frequency above which the
high-frequency content of the reverb sound will
be reduced, or "damped."
Adjusts the amount of damping applied to the
frequency range selected with HF Damp. With
a setting of "0," there will be no reduction of
the reverb's high-frequency content.
Parameter Value Explanation
GM2 REVERB
Type of reverb
Character 0–7
Cuts the high frequency range of the sound
coming into the reverb.
Pre-LPF 0–7
Level 0–127 Output level of reverberation
Time
0–127 Time length of reverberation
Adjusts the amount of the delay sound that is
Delay
0–127 fed back into the effect when the Character
Feedback
setting is 6 or 7.
0–5: reverb
6, 7: delay
Higher values will cut more of the high
frequencies.