Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use.
1203 lycoming Mall Circle Muncy, pA 17756 phone: (570) 546-9663 Fax: (800) 438-5901 the h7583 tenoning Jig is designed to work with E-Mail: techsupport@grizzly.com most table saws. use the table saw requirements listed below to verify that your table saw will work if you have any comments regarding this manual, with the tenoning jig.
If you have never used this type of machine or equipment before, WE STRONGLy REcOMMEND that you read books, trade magazines, or get formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.
TIRED OR UNDER THE INFLUENCE OF RESPIRATOR WHEN OPERATING DRUGS OR ALCOHOL. Be mentally alert MACHINERY THAT PRODUCES DUST. at all times when running machinery. Most types of dust (wood, metal, etc.) can cause severe respiratory illnesses. h7583 tenoning Jig...
Page 7
16. MAKE SURE GUARDS ARE IN PLACE that type of dust. AND WORK CORRECTLY BEFORE USING MACHINERY. h7583 tenoning Jig...
Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condi- tion of your shipment, inventory the contents. h7583 tenoning Jig...
G2544—Solvent cleaner & Degreaser H9692—Orange power Degreaser great products for removing shipping grease. figure 4. Model h7583 inventory. if any nonproprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.
Bar Adjustment (page 12). • injury. • side support Adjustment (page 12). the Model h7583 tenoning Jig is designed to work with a table saw that has a ⁄ " x ⁄ " miter •...
(see figure 8). rotate the micro-adjust knob counterclock- wise to force the slide plate to move and separate from the micro-adjust screw, as shown in figure 9. -10- h7583 tenoning Jig...
Page 13
11. perform the outward mounting procedure but install the guide bar using the left row of mounting holes on the base plate. long screw figure 11. slide plate positioned over the base plate. -11- h7583 tenoning Jig...
Removal of the washer will allow the tenoning jig to figure 13. guide bar. come loose from the table during a kickback situation, possibly causing a serious per- sonal injury or property damage. -12- h7583 tenoning Jig...
Make sure the jig side support is perpen- dicular to the table (refer to Side Support adjustment on page 12 for detailed instruc- tions). Clamp shoe slide plate figure 17. Checking for side support parallelism with the saw blade. -14- h7583 tenoning Jig...
Page 17
(see figure 17), then loosen the cap screw. -15- h7583 tenoning Jig...
18–19. individual working conditions. use this and other machinery and tools with caution and respect. failure to do so could result in seri- ous personal injury, damage to equipment, or poor work results. -16- h7583 tenoning Jig...
Page 20
OFF, disconnect mounted. it from power, and wait for the blade to come to a complete stop before removing the workpiece or moving the jig to avoid making contact with the spinning blade. -18- h7583 tenoning Jig...
Page 21
Note: Do not move the jig and workpiece into and the workpiece is properly mounted to the the blade quickly or the force of the blade will jig. attempt to lift the jig up and away from the table. -19- h7583 tenoning Jig...
Page 22
26. Making the third and fourth cheek cuts. 11. turn the saw OFF, disconnect it from power, wait for the blade to come to a complete stop, then remove the jig and additional base piece from the table. -20- h7583 tenoning Jig...
Page 23
Steps 3–7 for the remaining three shoulder cuts. When all the steps of these procedures are suc- cessfully performed, your basic tenon is com- plete. -21- h7583 tenoning Jig...
175 pages. figure 30. g1955 oxisolv spray. ® figure 32. Classic Joints with power tools. -22- h7583 tenoning Jig...
Page 25
H4332—T4 Silencer for Saw blades Woodworkers across the country swear by these blade silencers. power Twist v-belts ® H9815—a ⁄ " x 4' H9817—b ⁄ " x 6' figure 5. g4179 power Feeder. Works with multi-sheave pulleys. reduces noise! -23- h7583 tenoning Jig...
SEcTION 5: MaINTENaNcE cleaning always disconnect power to the table saw before Cleaning the Model h7583 is relatively easy. performing adjustments, Clean off the wood chips and sawdust, then wipe maintenance, or service off the remaining dust with a dry cloth. if any resin...
Would you recommend Grizzly Industrial to a friend? _____ Yes _____No Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times. _____ Yes _____No 10.
Page 30
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 32
Buy Direct and Save with Grizzly – Trusted, Proven and a Great Value! ® ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777...