Operating Instructions - Gemini CD-9800 Operation Manual

INTRODUCTION
Congratulations on purchasing a Gemini CD-9800 Dual CD Player. This
state of the art professional CD player includes the latest features and is
backed by a three year warranty. Prior to use, we suggest that you
carefully read all the instructions.
FEATURES
• Frame Accuracy
• Auto Cue
• Direct Access
• Continuous Play
CAUTIONS
Do not use this CD Player where the temperatures go below 41°F/5°C or
exceed 95°F/35°C.
Place the unit in a clean and dry location.
Do not place the unit in an unstable location.
When disconnecting the power cord from an AC outlet, always grasp it
by the plug. Never pull the power cord.
To prevent electric shock, do not remove the cover or the bottom
screws. There are no user serviceable parts inside. Please refer
servicing to a qualified technician.
Do not use chemical solvents to clean the unit.
Keep the laser pickup clean by keeping the drawer closed.
Keep this manual in a safe place for future reference.
SAFETY CERTIFICATIONS
Laser Diode Properties
Material: Ga - Al - As
Wavelength: 755 - 815 nm (25° C)
Laser Output: Continuous Wave, max. 0.5mW
IMPORTANT NOTE
Since the CD-9800 is a dual CD player, most of the functions and
controls are duplicated on both sides of the CD player. To eliminate
confusion and to make the drawings easier to understand, we will only
number the right side functions and controls. The only controls that are
not duplicated are the POWER SWITCH (1), VOLTAGE SELECTOR
SLIDE SWITCH (20), REMOTE JACK (23) and the PLAYER JACK (22).
LINE VOLTAGE SELECTION
Model CD-9800 is a dual voltage unit. It will operate at 115 or 230 volts.
The unit is preset at the factory to 115 volts. To set the proper voltage
follow these steps:
1. Place the head of a screw driver in the center of the VOLTAGE
SELECTOR SLIDE SWITCH (20) found on the rear panel.
2. Slide the switch left for 115 volts or push the switch right for 230
volts.
3. Do not force or twist the switch. Excessive force may cause damage.
If the switch does not move smoothly, contact a qualified technician.
CONNECTIONS
1. Using the included cable, plug one end into the REMOTE JACK (23)
and the other end into the PLAYER JACK (22).
2. Plug one end of a set of RCA connectors into each of the LINE
OUTPUT JACKS (21).
3. Plug the other end of the RCA connectors into any available line level
input jacks on your mixer. If you are playing the CD-9800 through a
receiver, you can plug the RCA connectors into the CD or AUX input
jacks on your receiver. If there are no CD or AUX inputs, use any line
level (not phono) inputs.
• Variable Pitch Control
• Pitch Bend
• Single Play
• BNC Output

OPERATING INSTRUCTIONS

1. Make sure that the VOLTAGE SELECTOR SLIDE SWITCH (20),
found on the rear panel, is set for the proper voltage. Plug the unit in
and press the POWER SWITCH (1). The unit will turn on. Pushing
the POWER SWITCH (1) a second time will turn the unit off.
2. Press the OPEN/CLOSE BUTTON (3), place a CD in the DISC TRAY
(2) and press the OPEN/CLOSE BUTTON (3) again. The tray will
close into the unit. The display will initially show the number of tracks
and the total time of the CD and the unit will be in the pause mode
(play/pause LED blinks green). When the display shows track number
1 and remain time of the first track, the unit is ready to use.
3. Push the TRACK SKIP BUTTONS (6) to select the track you want to play.
4. Use the TIME BUTTON (10) to select the time display you prefer
(real time, track time remaining and total track time remaining).
5. Press the PLAY/PAUSE BUTTON (5) and the unit will instantly play.
FUNCTION DESCRIPTIONS
POWER SWITCH : After making sure that the VOLTAGE SELECTOR
SLIDE SWITCH (20), found on the rear panel, is properly set, plug
the unit in and press the POWER SWITCH (1). The unit will turn on.
Pushing the POWER SWITCH (1) a second time will turn the unit off.
DISC TRAY : The DISC TRAY (2) is where the CD is held during loading,
unloading and playback. Pressing the disc tray OPEN/CLOSE
BUTTON (3), will open or close the tray. The DISC TRAY (2) holds
both 12 cm and 8 cm CDs. Please note: If the CD-9800 is in the play
mode, the tray will not open.
OPEN/CLOSE BUTTON : Press the OPEN/CLOSE BUTTON (3) to load
or remove a CD from the DISC TRAY (2).
DISPLAY : The DISPLAY (4) shows the track number, play mode, pause
mode, pitch and 3 different time displays (real time, track time remain
and total track time remain). Time is measured in minutes, seconds
and frames.
AUTO CUE FUNCTION : Pressing the SINGLE (17) button will activate
the AUTO CUE FUNCTION and cause the unit to stop at the
beginning of music of the following track. This allows you to start play
immediately from the start of music without any blank space (which
exists at the beginning of every track).
PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (5) causes
the operation to change from play to pause or from pause back to
play. See the CUE INSTRUCTIONS section for more information.
TRACK SKIP : The TRACK SKIP BUTTONS (6) let you select the track
to play.
SEARCH JOG WHEEL : The SEARCH JOG WHEEL (7) is used to
accurately position the disc at the point where you wish the track to
start playing. This position on the track will be memorized as the CUE
POINT. Each move of the SEARCH JOG WHEEL (7), in PAUSE
MODE, will move the memorized CUE POINT. See the CUE
INSTRUCTIONS section for more information.
SCAN DIAL : Use the SCAN DIAL (8) to select the scanning direction
and speed. Turning the dial in the clockwise direction will scan
forward and counterclockwise will scan in reverse. The scanning
speed increases as the dial is turned further.
STOP : The STOP BUTTON (9) will end the playing of the CD. Pressing
the STOP BUTTON (9) will also clear the cues.
TIME : The TIME BUTTON (10) switches the time display between the 3
different time displays (real time, track time remaining and total track
time remaining).
CUE 1 and CUE 2 : Use the CUE BUTTONS (11) in setting cue points.
See the CUE INSTRUCTIONS section for more information. In play
mode, pressing a CUE BUTTON will pause play and bring you to the
CUE POINT when you can then press the play/pause button to play
from the CUE POINT. In play mode, holding down the CUE BUT-
TONS (11) for more than 3 seconds clears the cue.
4%, 8% and 16% BUTTONS : Use the 4%, 8% and 16% BUTTONS (12)
to assign the percent the pitch control slide will have. The 4% button
will assign +/-4% to the pitch control slide. The 8% button will assign
Page 2