Advertisement
HEATING LIQUIDS
You can also use this appliance to heat liquids other
than milk, with excellent results.
1.Turn the appliance on by pressing the ON/OFF
button (fig. 4).
2.Pour the liquid to be heated (punch, water, etc) into
the milk tank.
3.Turn the froth regulator to the right
place a cup under the milk tube (fig. 17).
4.Wait for the IFD light to come on (fig. 16) then press
the IFD button immediately (fig. 18).
5.When you have run off the required quantity of
liquid, press the "IFD" button again to interrupt
delivery.
CLEANING AND MAINTENANCE
Before cleaning the outside of the appliance, always
turn off, unplug from the mains socket and allow to
cool.
Cleaning the cappuccino maker
The cappuccino maker must be cleaned each time you
use the appliance. Proceed as follows:
• Lift the milk tank lid.
• With one hand press the release lever towards the
left and at the same time lift the tank up (see fig.
21).
• After removing the milk tank, to reach internal
components, push the locking slide inwards (see
fig. 22).
• Lift the frothing chamber lid (see fig. 22).
NB: the frothing chamber lid cannot be lifted unless the milk
tank has been removed.
• Remove the rubber frother.
• Remove and wash with hot water with particular
attention to the four holes in the lid shown in fig.
23.
Make sure the hole indicated with the letter A is not
blocked. If necessary, clean with a needle. Take
care not to lose the gaskets. To facilitate cleaning
of the milk tube, all components must be replaced
correctly.
• Replace the milk tank and press down until it clicks
into place. Make sure it is correctly inserted by
pulling the tank gently upwards. It should not lift!
If it is not correctly in place, the device will not work
properly.
CLEANING THE FILTER HOLDER FOR GROUND
COFFEE
About every 300 coffees or when the coffee drips out
of the filter holder or not at all, clean the ground coffee
filter holder as follows:
• Remove the filter from the filter holder.
• Remove the filter cap (fig. 24) by unscrewing in the
direction indicated by the arrow on the cap.
(fig. 19) and
• Remove the frother from the container by pushing it
from the cap end.
• Remove the gasket.
• Rinse all components and clean the metal filter
thoroughly in hot water using a brush (fig. 25).
Make sure the holes in the metal filter are not
blocked. If necessary, clean with a pin (see fig. 26).
• Replace the filter and gasket on the plastic disk as
shown in fig. 27.
Make sure to insert the pin on the plastic disk into the
hole in the gasket indicated by the arrow in fig. 27.
• Replace the resulting assembly in the steel filter
container (fig. 28), making sure the pin is inserted
into the hole in the support (see arrow in fig. 28).
• Finally, screw on the cap.
Failure to clean as described above invalidates the
guarantee.
CLEANING THE BOILER OUTLET
About every 300 coffees, the espresso boiler outlet
must be cleaned as follows:
• Make sure the appliance is not hot and that it is
unplugged from the mains;
• Using a screwdriver, unscrew the screw fixing the
espresso boiler outlet (fig. 29);
• Clean the boiler with a damp cloth (fig. 14);
• Clean the outlet thoroughly in hot water using a
brush. Make sure the holes are not blocked. If
necessary, clean with a pin (fig. 26).
• Rub the boiler outlet while rinsing under the tap,
• Replace the espresso boiler outlet, making sure the
gasket is correctly positioned.
Failure to clean as described above invalidates the
guarantee.
OTHER CLEANING OPERATIONS
1.Do not use solvents or abrasive cleaning products to
clean the appliance. A soft, damp cloth is sufficient.
2.Clean the filter holder cup, filters, drip tray and water
tank regularly.
IMPORTANT: during cleaning, never immerse the
coffee machine in water. It is an electrical appliance.
15
Advertisement
