Advertisement
Printer Setup
Many of the printer's features may be set using menus available on the front panel of the printer.
For complete details, please refer to the MtP300 Series Operator's Manual.
To enter the Setup Mode, press and hold the
the
Enter Button until "Menus Active" is displayed.
While in Setup Mode, the power indicator will blink slowly. Upon entering Setup Mode, the FORMAT MENU is shown first. To
advance to the INTERFACE MENU or OPTIONS MENU, press the
When in Setup Mode, the current menu item is shown on the top line, and its corresponding value is shown on the bottom line. To
increment the value on the bottom line to the next setting, press the
Enter Button.
To exit Setup Mode, press the
Advance Button until "Exit Setup" is displayed. Press the
return to normal printer operation.
Printer Setup Menus
FORMAT MENU
Up to 5 formats can be stored
Format Name
+
Up to 16 Characters
M
Font
E
SansSerifA
N
4.2, 5.5, 10.2, 10.7, 16.9,18.5, 20.3;
U
Courier
12.7, 13.5, 14.5, 15.6, 16.9*,
18.5, 20.3, 22.6, 25.4
I
Spacing
T
0 - 10, 3*
E
Left Margin
0* - 1.0244"
M
Right Margin
S
0* - 1.2608"
Print Contrast
-75 to +125, 0* ~
Max Paper Speed
0.32 to 3.30* ~ ips
Form Feed Distance
0 – 2.5216", 1.2608* ~
Mark Sensing
Front*, Back ~ , Gap
Mark Sensitivity
-10 to +10, 0*
Gap Sensitivity
-10 to +10, 0*
Tear to Mark Dst
-0.7092" to 1.7927", 0*
Present Distance
0.0000"* to 1.2911"
Note: Based on Firmware Revision 2.9
Enter Button while turning on the printer with the
Advance Button.
Increment Button. To advance to the next menu item, press the
• Use the
Advance Button to access the next menu. (Also see + note below)
• Use the
Increment Button to increment the value displayed on the bottom line.
• Use the
Enter Button to accept the value displayed and advance to the next feature.
INTERFACE MENU (IrDA, Bluetooth, or Wi-Fi are only available if that option is installed)
Serial
IrDA
Emulation
Emulation
Printek*, O'Neil,
Printek*,
ZPL-II, Mt3, CPCL
O'Neil,
Hex Dump
ZPL-II, Mt3,
Baud Rate
CPCL,
9600, 19200,
Hex Dump
38400, 57600*
Data Bits
7, 8*
Stop Bits
1*, 2
Parity
None*, Even, Odd
XON/XOFF
Off*, On
ETX/ACK
Off*, On
RTS/CTS
Off, On*
* Factory default value.
+
When changing value for this feature, use
character/field in value.
~ LP Model Defaults: Print Contrast = +35, Max Paper Speed = 2.30ips,
Form Feed Distance = Mark Sensing, Mark Sensing = Back.
Power Button. Continue to hold
Enter Button to save the changes and
Bluetooth
Wi-Fi
Emulation
Emulation
Printek*, O'Neil,
Printek*, O'Neil, ZPL-II,
ZPL-II, Mt3, CPCL,
Mt3, CPCL, Hex Dump
Hex Dump
WLAN Type
Pairing Mode
Infrastructure*, Peer-to-Peer
Paired*, Unpaired
WLAN Channel
Role Policy
1* – 14
Defer*, Master
WLAN SSID
+
Discoverability
any*
On*/Off
WLAN WEP Bits
Pin
0*, 64, 128
0*, Up to 16
WEP Key 1-4
+
Numeric Chars.
10 or 26 Char. Hex String
Security
WLAN Auth
Off*, On
Auto*, Open, Shared
Local Name
IP Address Assign
+
MtP300-Serial#*
DHCP*, Static
Address
IP Address
+
(Displayed Only)
0.0.0.0*
IP Subnet Mask
+
0.0.0.0*
IP Gateway
+
0.0.0.0*
Tunnel Port#
+
08023*
Advance Button to advance to the next
Message Window
Power
Increment
IrDA Window
Indicators:
Power On = Ready to print, Slow Flash = Setup Mode,
Short Flash = Power Saving Stand By Mode.
Wireless I/O Enabled and Connected.
Magnetic Card Reader: Ready for swipe.
Error: See messages, below.
Battery: On = Charging, Flashing = Battery Low.
Paper Related Messages:
Paper Door Open - Close paper door and press
the
Paper Feed
continue.
Paper Fault -
Insert paper or correct jam and
press the
to continue.
Magnetic Card Reader Messages:
Swipe Card Now - Magnetic Card Reader is ready
for card to be swiped.
Card Read Ok -
Card read successfully.
Card Not Read -
Card not read correctly.
OPTIONS MENU
Max Format #
+
1* – 5
Auto Power Down
Off*, 1 – 15 Minutes
User Language
English*, French, German
Truncate Lines
No*, Yes
Print Promo
No*, Yes
Note: After exiting Setup, you may print the current
Interface settings by pressing and holding the
Button until "Printing Setup" is displayed.
Printek Part Number 6038 Rev. C
Paper Feed
Enter
/Advance
Button to
Paper Feed
Button
Enter
Advertisement
