NAPCO GEM-RP3DGTL Installation Instructions Manual page 8

Programming the GEM-P816 & GEM-P1632 (v.9A and Earlier)
28
INTERIOR BYPASS
BYPASS
INTERIOR
(Direct Entry)
A
Zone # 6-digit RF ID #
Quick Method. If a receiver is already installed in the panel, Napco
transmitter wireless points can be programmed automatically ("enrolled") using the following procedure. NOTE: The
transmitter point will be enrolled only if the signal strength is 3 or greater.
1. Enter the zone number to which the transmitter point will be mapped.
2. Press the
B
3. Open the loop of the point that is to be programmed (GEM-TRANS2 only).
4. Install the transmitter battery. The keypad will beep once to indicate that the point has been successfully enrolled.
Multi-point transmitters can be mapped to successive zones simultaneously (Example 1) or to selected zones point by
point (Example 2):
Example 1. A GEM-TRANS2 transmitter has the RF ID number 410078:1.
respectively.
1. Enter the Enroll mode as described in step 2 above.
2. Enter Zone "11".
3. Open the loops of points 1 and 2.
4. Install the transmitter battery. The keypad will beep 3 times to indicate that three points have been programmed.
Transmitter 410078:1, point 1 will be mapped to Zone 11.
Transmitter 410078:1, point 2 will be mapped to Zone 12.
The keypad will now display Zone 12, the last zone enrolled.
Example 2. A GEM-TRANS2 transmitter has the RF ID number 287613:1. Map point 1 to Zone 6 and point 2 to Zone 9.
1. Enter the Enroll mode as described above.
2. Enter Zone "06".
3. Open point-1 loop.
4. Install the battery. The keypad will beep once to indicate that one point has been programmed. (Transmitter
287613:1, point 1 will be mapped to Zone 6.)
5. Enter Zone "09".
6. Close point-1 loop and open point-2 loop.
7. Remove the transmitter battery, then re-install it. The keypad will beep once to indicate that one point has been
programmed. (Transmitter 287613:1, point 2 is mapped to Zone 9).
KEY FOB ZONE ASSIGNMENT: Key fobs can also be assigned to zones to allow multiple wireless panic buttons on
one alarm system, each reporting to a central station, or pager while having a description on the keypad that describes
the person holding the key fob, the location where the person holding the key fob is stationed, or the special purpose of
the key fob button being depressed. See the next page on Key fob Zone Assignment.
8
RF Transmitter Programming
(For wireless systems only. Also see Quick Method, which follows)
Press the
FIRE/TBL SYS TBL CHIME
then directly enter:
The zone number (01–32) to which the transmitter will be mapped,
1
including leading zeros. Press the
FIRE/TBL SYS TBL CHIME
2 The 6-digit RF ID # printed on the transmitter and box.
3 The 1-digit checksum number (C) printed on the transmitter and box.
4 The Point number (1–4) (P); enter "9" for unsupervised (all points).
Press
transmitters are entered, press NEXT (
Checksum # Point #
button to enter the Enroll Mode. The red and green LEDs on the keypad will flash.
button and for each transmitter (key fob transmitters also),
A
D
to save. Then go to step 1 to enter next transmitter. When all
NOTE: When programming the RF ID number:
"A" =
"C" =
"E" =
button again.
A
) button to proceed.
E
; "B" =
G 0 G 1 ;
; "D" =
G 2 G 3
; "F" =
G 4 G 5
Map both points to Zones 11–12,
;
.