NAPCO GEM-RP3DGTL Installation Instructions Manual page 2

THE GEM-RP3DGTL KEYPAD
DESCRIPTION
The GEM-RP3DGTL is a dual 7-segment digital keypad that is compatible with the NAPCO GEM-Series GEM-P816,
P1632, P3200 & P9600 control-panels. Refer to User Guide OI249 for operation instructions. While the GEM-
RP3DGTL may be used to fully program the control, the GEM-RP1CAe2 keypad provides the optimum in ease of
keypad programming.
ORDERING INFORMATION
Note: Any of the following Napco wireless transmitters may be used with the GEM-RECV Series Receivers. Bat-
teries are included with all transmitters.
GEM-TRANS2 - Window/Door Sensor. This supervised, two-point transmitter provides an internal magnetic reed
switch and/or terminals for two external normally-closed devices, or one external normally-open device.
GEM-RECV8: Wireless Receiver, 8 Zones
GEM-RTRANS: Recessed Window/Door Transmitter
GEM-PIR - Wireless PIR Motion Sensor.
GEM-PIRPET - Wireless 30 lb. pet immune PIR Motion Sensor.
GEM-DT - Dual-technology PIR/microwave sensor.
GEM-SMK - Wireless Photoelectric Supervised smoke detector.
GEM-HEAT - Wireless Heat Detector 135°F / Rate of Rise.
GEM-KEYF - Hand-Held Key Fob Transmitter. Key chain/Pendant remote arming or emergency transmitter.
GEM-WP - Wireless Waterproof Panic Button.
GEM-GB - Glass-break sensor.
GEM-TRANS2 - 2-Point Window/Door Transmitter
DL123A - Replacement Lithium Battery for GEM-TRANS2, GEM-PIR (2), GEM-PIRPET(2) and GEM-GB (2) (bulk
packed).
SPECIFICATIONS
Operating Voltage: 12VDC (supplied by panel)
Current Drain: 50 mA Standby
Note: Subtract keypad current from combined auxiliary current of the control panel.
Operating Temperature: 0° C to 49° C
Storage Temperature: 20° C to + 85° C
Power Requirements: 12VDC, 45mA (supplied by panel)
Dimensions: 5 7/8" x 4 3/8" x 1" (WxHxD)
MOUNTING THE KEYPAD
A keypad should be located near each exit/entry door. To open the case, insert a screwdriver into either slot at the
bottom and push up with a slight twisting motion to release the retainer tab. Repeat for the other slot. Pull out at the
bottom and lift off the two hooks at the top.
The GEM-RP3DGTL features a handy pull-up reference label. (This label must be used in UL installations). Before
mounting the keypad onto the wall, push the Sliding Label Plate (with label and felt backing affixed and handle facing
forward) down the guides at the rear of the keypad until it snaps into place. Once installed, the Sliding Label Plate
cannot be removed without first removing the keypad from the wall. Note: The keypad fire and panic keys should not
be considered a substitute for a listed manual initiating device, such as a pull box.
If installing onto a double-gang box, insert mounting screws through the two vertical elongated holes on the left side of
the case and into the box. If the box is visible when viewed from the front, adjust the keypad vertically and tighten the
screws. Then, using hardware suitable for the mounting surface, add one or two screws at the right side of the keypad
case directly into the wall to ensure a secure installation. Note: Do not over tighten the screws! Uneven walls may
cause the keypad case to distort.
2
Note: Do not mix classic RP series keypads with "K Series" keypads within one system.
For Sales and Repairs, call toll free: (800) 645-9445
For direct line to Technical Service, call toll free: (800) 645-9440
Internet: http://www.napcosecurity.com