NAPCO GEM-RP3DGTL Installation Instructions Manual page 5

Programming the GEM-P816 & GEM-P1632 (v.9A and Earlier) with the GEM-RP3DGTL
Refer to the GEM-P9600/3200 Programming Manuals (WI1185 & WI1184) and follow the GEM-RP3DGTL
Keypad Easy Programming Mode instructions. The following applies to the GEM-P816/1632:
01
(Direct Entry)
BYPASS FIRE/TBL
INTERIOR
INTERIOR BYPASS FIRE/TBL
enter the total number of zones required for Areas 1 & 2. The Direct Address Program Mode can then be used to
remove zones from Area 1 and place them in Area 2. See Zone Options. If Programming a Wireless Only system, or
using wireless only on Zones 9-32, enter the total number of zones in system. Enter the transmitter points in the RF
Transmitter section of the Easy Menu Driven Programming Mode.
03
(Press YES or NO)
INTERIOR BYPASS FIRE/TBL
BYPASS FIRE/TBL
INTERIOR
04
(Press YES or NO)
BYPASS FIRE/TBL
INTERIOR
BYPASS FIRE/TBL
INTERIOR
05
BYPASS FIRE/TBL
INTERIOR
BYPASS FIRE/TBL
INTERIOR
(Press YES or NO)
06
(Yes or No)
GEMINI
SYSTEM ARMED
ENT A1
01/01/97 12:00AM
BYPASS FIRE/TBL
INTERIOR
NEXT/YES
A 1 2 3 E
D
PRIOR/NO
B 4 5 6 F
AREA
C 7 8 9 0 G
COMPUTERIZED SECURITY SYSTEM
R
BYPASS FIRE/TBL
INTERIOR
Total Number of Zones in Area 1
Press the
be programmed for Area 1. Valid entries are from 01 to 32. Directly enter
SYS TBL CHIME
the total number of zones, including leading zeros. Use number buttons
through
1
system is based on groups of 4 zones each (after the first 8 zones), and will
automatically round up to the next group of 4. For example, if you enter 18, it
SYS TBL CHIME
will automatically convert this to 20 zones. Press
( ) button to proceed. NOTE: If you are programming a 2 Area system,
E
Panel Zone Doubling?
If the total number of zones in Area 1 entered was 16 or greater, press YES
( ) to effectively double the capacity of the control panel's hard wired
E
SYS TBL CHIME
zones from 8 to 16.
but will be designated for Normally Closed devices only.
Zone 1 will now support Zones 1 and 9 with the use of the supplied EZ Zone
TM
Doubling
SYS TBL CHIME
Instructions).
NOTE: Answer NO for GEM-P816.
Fire Zones in Area 1
button and then directly enter the zone number of any zones which are to be
used as Fire Zones (both 2-wire, 4-wire or wireless). Valid entries are from
SYS TBL CHIME
01 to 32. Directly enter each zone number, including leading zeros, and
D
press to save, and then repeat for any additional zone(s). Press NEXT
( ) button to proceed.
E
SYS TBL CHIME
2-Wire Fire Zones in Area 1
button and then directly enter the zone number of any Fire Zones
A
(from previous question) which are to be used with 2-wire smoke detectors.
SYS TBL CHIME
The only valid entries are 07 and 08. Directly enter each zone number,
including leading zeros. Press
zone(s). NOTE: Only zones which have been designated as Fire Zones may
SYS TBL CHIME
be programmed as 2 Wire Fire zones. Press NEXT (
proceed. NOTE: JP3 must be set to "2-WF" position for 2-wire fire zones for
zones 7 and 8 (refer to Installation Instructions).
Report all Zones to Central Station?
Press YES (
( ) button for no zones to report (LOCAL SYSTEM).
F
SYS TBL CHIME
SYS TBL CHIME
button and then directly enter the total number of zones to
A
. NOTE: Press the
9
(Appears for New Panel Only) (GEM-P1632 only)
The 16 zones can no longer use normally open devices
resistors, supplied. (Refer to Wiring Diagram and Installation
If Panel Zone doubling is not desired, press NO (
(Appears for New Panel Only) Press the
D
to save and then repeat for any additional
) button for all zones to report to central station; press NO
E
(Appears for New Panel Only)
button for a zero. The
0
D
to save. Press NEXT
(Appears for New Panel Only) Press the
) button to
E
(Appears for New Panel Only)
The terminal for
).
F
A
5