Sound Menu; Picture Menu - Sanyo CE27LD4-B Instruction Manual

Many of your TV's functions are controlled through the menu function.
MENU
Picture
Brightness
Contrast
Colour
Sharpness
Tint (only if NTSC equipment is detected)
Text brightness
Memory
Volume
Sound
Bass
Treble
Balance
BBE
Timer OFF Timer
Alarm Timer
Setting Child lock
AV2
Noise Reduction
Auto Tuning
Preset
Auto sort
Prog. Preset
Swap
Fine Tuning
During menu operation a bar at the bottom of the screen show which
controls can be used.
eg.
Press the u button to enter and exit the 5 sub menus Picture,
Sound, Timer, Setting and Preset.
When a sub menu is selected its options are displayed and its colour
will change to yellow.
When you have set each Sub menu you can either press the MENU
button to exit and clear the screen or press the 5 button until the
sub menu is re-selected. Using the 7,8 button you can rotate again.

Picture menu

Press the 7 or 8 button and select Picture menu, set the picture
settings for your personal preference.
Picture
Brightness
Contrast
Colour
Sharpness
Tint
Text brightness
Memory
Use the e or d button to select eg. Brightness and the 7 or 8
button to adjust levels.
Tint : is only available if NTSC equipment is connected.
Text brightness : you can set to Minimum, Centre or Maximum.
Use the e or d button to select and the 7 or 8 button to set.
To memorise these settings press the F/OK button. (The OK? will
change to OK.)
To exit press the MENU button.
MENU OPERA
MENU OPERA
ON/OFF
Video/S-video
ON/OFF
Auto Channel
Start
Position
Semi Channel
Position
Skip
Memory
Timer
OFF timer
Alarm timer
38
42
19
2
27
Minimum/Centre/Maximum
OK? / OK
TION - Analogue channels
TION - Analogue channels
Press the MENU button and select Sound menu by pressing the 7
or 8 button.
Select and adjust to obtain the best sound settings for your environment
using e or d and 7 or 8 button.
Sound
Volume
Bass
Treble
Balance
BBE
To exit press MENU button.
Off-timer setting
The Off timer will switch the TV set into the standby mode when the
selected time has elapsed.
1. Press the MENU button and select Timer using 7 or 8 button.
Select OFF Timer using the e or d button. The complete line
turns yellow.
2. Press the 7 or 8 button to select --:-- (highlighted yellow).
3. Press the e or d button to change time.
The time changes in 30 minute steps.The maximum time is 2:00hrs.
4. Press the 7 or 8 button to highlight complete line (yellow).
5. Press the OK button to store your settings.
If you have set the off timer, then one minute before the TV switches
off, a display appears on the screen.
If the TV set is switched off by the standby button on the remote
control or by the standby switch on the front of the TV set the
timer settings will be cancelled.
Press the MENU button to exit, or press the 7 button to highlight
complete line yellow and then press the d button to set Alarm timer.
Timer
OFF timer
Alarm timer
Alarm timer setting
This function can be set so that an alarm goes off. This only hap-
pens when the TV is switched on. It may remind you to do something.
1. Press the MENU button and select Timer using the 7 or 8
button. Select Alarm timer using the e or d button. The complete
line turns yellow.
2. Press the 7 or 8 button to select --:--.
3. Press the e or d button to change time.
The display changes in 5 minute steps and the maximum time period
is 3:00 hours.
4. Press the 7 or 8 button to highlight complete line (yellow).
5. Press the OK button to set the Alarm.
When the time period is up, the time up signal will appear on the
screen and the alarm will sound for 15 seconds.
To cancel the Alarm timer press any button and the display will
disappear.
If the TV set is switched off by the standby switch on the remote
control, the standby switch on the front of the TV or a power failure
occurs the timer settings will be cancelled.

Sound menu

12
0
0
0
ON / OFF
Timer menu
OK?
- - : - -
- - : - -
15