Table of Contents
Advertisement
Quick Links
PM2M/PM2MP
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-PM2MP
Rev:1.0
Release date: June 2004
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Advertisement
Table of Contents
Related Manuals for JETWAY PM2M
Summary of Contents for JETWAY PM2M
- Page 1 PM2M/PM2MP USER'S MANUAL M/B For Socket 478 Pentium 4 Processor NO. G03-PM2MP Rev:1.0 Release date: June 2004 Trademark: * Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
-
Page 2: Table Of Contents
TABLE OF CONTENT USER’S NOTICE........................ii MANUAL REVISION INFORMATION ................ii COOLING SOLUTIONS ......................ii CHAPTER 1 INTRODUCTION OF PM2M/PM2MP FEATURE OF MOTHERBOARD ..................1 SPECIFICATION........................2 PERFORMANCE LIST ......................3 LAYOUT DIAGRAM & JUMPER SETTING ..............4 CHAPTER 2 HARDWARE INSTALLATION HARDWARE INSTALLATION STEPS ................6 CHECKING MOTHERBOARD'S JUMPER SETTING........... -
Page 3: User's Notice
REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER. THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE PM2M/PM2MP MOTHER- BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. -
Page 4: Chapter 1 Introduction Of Pm2M/Pm2Mp
Introduction of PM2M/PM2MP Motherboard 1-1 Feature of motherboard The PM2M/PM2MP motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package Processor with the VIA P4M266A(CE) Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 2.0GB. -
Page 5: Specification
1-2 Specification Spec Description ∗ Micro ATX form factor 4 layers PCB size: 24.4x18.0cm Design ∗ VIA P4M266A(CE) North Bridge Chipset Chipset ∗ VIA VT8235 South Bridge Chipset ∗ Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin CPU Socket (mPGA478B Socket) Grid Array (FC-PGA2) package processor ∗... -
Page 6: Performance List
1-3 Performance List The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.) Performance Test Report Intel Pentium 4 1.9GHz mPGAB package... -
Page 7: Layout Diagram & Jumper Setting
1-4 Layout Diagram & Jumper Setting (for PM2MP) PRINT PS/2 Mouse LINE-IN PS/2 Keyboard LINE-OUT COM1 USB1 CPU FAN K/B Power ON Jumper (JP1) CPU Socket PS2 KB/Mouse Port ATX 12V Power Connector DDR DIMM X2 PC99 Back Panel USB Power On Jumper (JP3) ATA 133 IDE Connector USB Port ATX Power Connector... -
Page 8: Expansion Sockets
Jumpers Jumper Name Description Page CMOS RAM Clear JBAT 3-pin Block Keyboard Power On Enable/Disabled 3-pin Block USB Power On Enable/Disabled JP3/JP4 3-pin Block Connectors Connector Name Description Page ATXPWR ATX Power Connector 20-pin Block P.11 ATX12V ATX 12V Power Connector 4-pin Block P.12 PS2KBMS... -
Page 9: Chapter 2 Hardware Installation
Chapter 2 Hardware installation 2-1 Hardware installation Steps Before using your computer, you had better complete the following steps: 1. Check motherboard jumper setting 2. Install CPU and Fan 3. Install System Memory (DIMM) 4. Install Expansion cards 5. Connect IDE and Floppy cables, Front Panel /Back Panel cable 6. -
Page 10: Install Cpu
(2) Keyboard/USB Power On function Enabled/Disabled: JP1, JP3/JP4 1-2 closed 2-3 closed Keyboard Power ON Disable Keyboard Power ON Enabled (Default) Keyboard Power On Setting 1-2 closed USB Power ON Disable 2-3 closed USB Power ON Enabled (Default) USB Power On Setting 2-3 Install CPU 2-3-1 Glossary Chipset (or core logic) - two or more integrated circuits which control the interfaces between... -
Page 11: About Intel Pentium 4 478-Pin Cpu
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and establish the relationship between the various components. Driver - software, which defines the characteristics of a device for use by another device or other software. Processor - the "central processing unit"... -
Page 12: Install Memory
2-4 Install Memory This motherboard provides 184-pin DDR DUAL INLINE MEMORY MODULES (DIMM) sites for DDR memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR SDRAM. Valid Memory Configurations Bank 184-pin DDR DIMM Total Memory Bank 0, 1 (DDR1) DDR266/DDR200 DDR DRAM Module... -
Page 13: Expansion Card
2-5 Expansion Cards WARNING! Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards. 2-5-1 Procedure For Expansion Card Installation 1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers. -
Page 14: Interrupt Request Table For This Motherboard
2-5-3 Interrupt Request Table For This Motherboard Interrupt request are shared as shown the table below: INT A INT B INT C INT D INT E INT F INT G INT H √ Slot 1 √ Slot 2 √ Onboard USB 1 √... - Page 15 ROW2 ROW1 3.3V 3.3V -12V 3.3V Soft Power On Power OK +5V (for Soft Logic) +12V Pin 1 (2) ATX 12V Power Connector (4-pin block) : ATX12V This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption.
- Page 16 VGA Connector (15-pin D-Sub) Connector: VGA VGA is the 15-pin D-Subminiature female connector for display monitor. PS/2 Mouse PRINT USB1 LINE-IN LINE-OUT PS/2 Keyboard COM1 (10) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives.
-
Page 17: Headers
(12) Secondary IDE Connector (40-pin block): IDE2 This connector connects to the next set of Master and Slave hard disks. Follow the same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. - Page 18 USB2 Pin 1 USB Port Headers IDE Activity LED: HD LED This connector connects to the hard disk activity indicator light on the case. Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch.
-
Page 19: Starting Up Your Computer
FAN Headers (3-pin) : SYSFAN, CPUFAN These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector. - Page 20 1. After all connection are made, close your computer case cover. 2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used.
-
Page 21: Chapter 3 Introducing Bios
Introducing BIOS The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. - Page 22 Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
-
Page 23: Standard Cmos Features
Use this menu to load the BIOS default values these are setting for optimal performances system operations for performance use. Load Standard Defaults Use this menu to load the BIOS default values for the stable performance system operation that are factory settings for normal use. Set Supervisor/User Password Use this menu to set User and Supervisor Passwords. -
Page 24: Advanced Bios Features
The time format is <hour><minute><second>. Primary Master/Primary Slave Secondary Master/Secondary Slave Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. - Page 25 Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep. Disabled (default) No warning message to appear when anything attempts to access the boot sector or hard disk partition table.
-
Page 26: Advanced Chipset Features
Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30. Typematic Delay (Msec) Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000. -
Page 27: Dram Timing Settings
Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled. Video RAM Cacheable Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. -
Page 28: Pci Timing Settings
CMOS Setup Utility – Copyright(C) 1984-2004 Award Software AGP Timing Settings AGP Share Memory Size Item Help AGP Aperture Size AGP Master 1 WS Write Enabled AGP Master 1 WS Read Enabled Menu Level >> CPU to AGP Post Write Enabled AGP Delay Transaction Enabled... -
Page 29: Onchip Ide Function
Please refer to section 3-7-1 OnChip Device Function Please refer to section 3-7-2 Onboard Super IO Function Please refer to section 3-7-3 Init Display First This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings are: PCI Slot, AGP Slot. -
Page 30: Onchip Device Function
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support. The settings are: Enabled, Disabled. -
Page 31: Power Management Setup
CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Onboard Super IO Function Onboard FDD Controller Enabled Item Help Onboard Serial Port 1 3F8/IRQ4 Onboard Serial Port 2 2F8/IRQ3 Onboard Parallel Port 378/IRQ7 Menu Level >> Parallel Mode ECP Mode Use DMA ↑↓→←... -
Page 32: Pm Wake Up Events
The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use. CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Power Management Setup ACPI Function Enabled Item Help... -
Page 33: 3-8-1.1 Irqs Activities
CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Wake Up Events Item Help LPT & COM LPT/COM HDD & FDD PCI Master Menu Level >> Wake-Up on Ring/LAN Disabled Wake-Up on PCI PME Disabled PS2 KB Wake up Selection Hot Key Wake-Up on RTC Alarm Disabled x Date of Month Alarm... -
Page 34: Irq Resources
This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. -
Page 35: Pc Health Status
CMOS Setup Utility – Copyright(C) 1984-2004 Award Software IRQ Resources Item Help IRQ5 assigned to PCI Device IRQ7 assigned to PCI Device IRQ9 assigned to PCI Device Menu Level >> IRQ10 assigned to PCI Device IRQ11 assigned to PCI Device IRQ12 assigned to PCI Device... -
Page 36: Load Standard/Optimized Defaults
This section is for setting CPU Frequency/Voltage Control. CMOS Setup Utility – Copyright(C) 1984-2004 Award Software Miscellaneous Control CPU Clock Ratio Item Help Auto Detect DIMM/PCI Clock Enabled Spread Spectrum Disabled ** Current Host/PCI Clock is 100/33MHz ** Menu Level > Host/PCI Clock at Next Boot is 100/33MHz ** Current DRAM Clock is 133MHz **... -
Page 37: Set Supervisor/User Password
Load Standard Defaults When you press <Enter> on this item, you get confirmation dialog box with a message similar Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations. Load Optimized Defaults When you press <Enter>... -
Page 38: Chapter 4 Driver & Free Program Installation
DRIVER & FREE PROGRAM INSTALLATION Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. - Page 39 IDE : VIA ATAPI VENDOR SUPPORT DRIVER IS USED TO FIXED COMPATIBILITY ISSUE FOR IDE DEVICES AGPVXD : VIA AGPVXD DRIVER IS TO BE INSTALLED, IF YOU ARE USING AN AGP VGA CARD, VIAGART.VXD WILL PROVIDE SERVICE ROUTINES TO YOUR VGA DRIVER AND INTERFACE DIRECTLY TO HARDWARE, PROVIDING FAST GRAPHIC ACCESS IRQ ROUTING :...
-
Page 40: Vga Install Prosavage Ddr Vga Driver
7. Click NEXT to Install VIA AGP VXD Driver 8. Click NEXT to Install VIA IRQ Routing Mini port Driver 9. Click Finish to restart computer 4-2 VGA install PROSAVAGE DDR VGA Driver For WINDOWS 9X/ME/NT4.0/2000/XP 1. Click VGA when MAGIC INSTALL MENU Click NEXT When ProSavageDDR Driver appears Install Setup Wizard Appears... -
Page 41: Sound Install Ac97 Audio Codec Driver
4-3 Sound Install AC97 Audio Codec Driver 1. Click SOUND when MAGIC INSTALL 2. Then auto detect operation system language MENU appears edition, click NEXT, start to install DRIVER 3. Click NEXT 4. Click Continue Anyway 5. Click Finish and Restart Windows 6. -
Page 42: Lan Install Via 10/100Mb Lan Controller Driver
Note: The path of the file For WIN98/NT4.0/WIN2K/XP is X:\CODEC\VIACODEC\SETUP.EXE Note: In Win2K/WinME users have to click Control Panel\System\Device Manager\ DVD\CD-ROM drives to Enabled digital CD Audio for the CD-ROM Device when use the SPDIF-Out digital signal. 4-4 LAN Install VIA 10/100MB LAN Controller Driver (Only for PM2MP) The VIA10/100MB PCI Ethernet Adapter Driver path is X:\VIA\LANDRV Click LAN when Magic Install Menu appear 2. - Page 43 4-5 PC-HEALTH ITE Smart Guardian Software The path of the file is X:\VIA\ITESMARTGD\SETUP.EXE (Support Windows 9X/ME/2K/NT/XP) 1. Click PC-Health when Magic Install Menu Click Next , install ITE Smart Guardian utility appears executing Program → ITE Smart Guardian , Click Finish , complete install ITE Smart Guardian utility The ITE Smart Guardian auto detect system voltage, Fan speed and CPU/ SYSTEM...
-
Page 44: Magic Bios Install Bios Live Update Utility
4-6 MAGIC BIOS Install BIOS Live Update Utility Click Magic BIOS when Magic Install Click Next to install the Magic BIOS in MENU appears Destination Folder After finish Setup you will have a Magic Double click the Magic BIOS icon you will BIOS icon in your screen have this picture, choose from internet you can upgrade BIOS On-line... -
Page 45: Usb2.0
When choose From Local Driver to update 10. Choose the correct BIOS file to update BIOS BIOS, you must have the correct BIOS file in your Local Driver 4-7 USB2.0 Install VIA USB2.0 Device Driver 1. Click USB2.0 when MAGIC INSTALL 2. -
Page 46: Pc-Cillin Install Pc-Cillin2004 Anti-Virus Program
4-8 PC-CILLIN Install PC-CILLIN 2004 Anti-virus program 1. Click PC-CILLIN when MAGIC INSTALL 2. Click NEXT when the "Trend Micro internet MENU appear security" installshield wizard windows appear 3. This is license agreement, select "I Accept 4. Click NEXT and Enter your Customer the terms"... -
Page 47: How To Disable On-Board Sound
STEP 2. Copy utility program to your boot disc. You may copy from DRIVER CD X:\FLASH\AWDFLASH.EXE or download from our web site. STEP 3. Copy latest BIOS for PM2M/PM2MP from our web site to your boot disc. STEP 4. Insert your boot disc into A:, start the computer, type “Awdflash A:\ PM2MPAxxx.BIN /SN/PY/CC/R”...