Epson ColorPage EPL-C8200 Quick Reference
Color laser printer
Hide thumbs
Also See for ColorPage EPL-C8200:
- Service manual (550 pages) ,
- Setup manual (90 pages) ,
- Unpacking manual (24 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Epson ColorPage EPL-C8200
Summary of Contents for Epson ColorPage EPL-C8200
-
Page 2: Replacing Consumable Products
If you can see the color that you need to replace, go when a notice message appears on the LCD panel or in to step 5. the EPSON Status Monitor 3 utility. If you see a different color, go to the next step. Toner Cartridge (Yellow) S050016 There is a switch located at the upper left. - Page 3 Turn the cartridge knob counterclockwise 90 Hold the cartridge with the arrow side facing up. degrees so that the O symbol on the knob is in the Insert it all the way into the cartridge slot. position shown below. By turning the knob, the cartridge extends slightly.
-
Page 4: Replacing The Photoconductor Unit
Replacing the photoconductor unit Turn the small lever to the right. Turn off the printer. Note: Before replacing the photoconductor unit, be sure to turn off the printer. Open the front cover. Pull the photoconductor unit about 30 cm out of the printer. - Page 5 Hold the handle at the top of the photoconductor Hold the handle on top of the photoconductor unit unit and gently pull it all the way out. and place the unit on the guide rails. Insert it all the way into the printer. Caution: Be sure not to touch the surface of the drum.
-
Page 6: Replacing The Waste Toner Collector
10. Turn the large lever clockwise 90 degrees. Grasp the handle and tab of the waste toner collector to release the lock. 11. Close the front cover. Pull out the waste toner collector. Replacing the waste toner collector Open the front cover. Take out a new waste toner collector. -
Page 7: Replacing The Fuser Oil Roll
Hold the handle of the collector and insert it into Hold the handle of the fuser unit and pull it all the the slot all the way until the tab clicks into place. way out. Close the front cover. Warning: Replacing the fuser oil roll Be careful not to touch the fuser which is marked CAUTION! HIGH TEMPERATURE, or the... - Page 8 Take a new fuser oil roll out of its box, and remove Push the roll down firmly until it clicks into place. the cover and two shipping pins as shown below: Note: Push the fuser unit into the printer until it clicks. Do not touch the white roll surface.
-
Page 9: Clearing Jammed Paper
Remove the jammed or crumpled paper. If the Clearing Jammed Paper paper is torn, be sure to remove all pieces. If jammed paper is torn and remains in the printer, or if paper is jammed in a place not mentioned in this chapter, contact your dealer. -
Page 10: Clearing The Mp Tray
Pull out the jammed paper from the bottom of the Pull the paper path unit out until it stops. Be careful paper path unit. not to tear the jammed paper. Open the unit cover by grasping the handle and Close the paper path unit firmly. pulling up. -
Page 11: Clearing The Fuser Unit
Turn the knob on the unit clockwise as shown Close the cover of the unit. below. The jammed paper should come out. Close the paper path unit firmly. After the jammed paper is ejected halfway, pull the Clearing the fuser unit paper up as shown below. - Page 12 Pull the fuser unit out gently until it stops. Be Caution: careful not to tear the jammed paper. Do not touch the fuser, which is marked CAUTION! HIGH TEMPERATURE, or the surrounding areas. If the printer has been in use, the fuser and the surrounding areas may be very hot.
-
Page 13: Clearing The Output Path Cover
Pull out the jammed paper. Clearing the output path cover Caution: When paper is jammed in the path to the face-down tray, clear it from the fuser unit. Do not pull jammed paper out from the face-down tray. Open the output path cover on the left side of the printer. - Page 14 Remove all jammed paper. If paper has jammed at Pull the jammed paper out gently. Be careful not to the top of the output path, gently lift it out. If it has tear the paper. jammed near the bottom of the output path cover, carefully pull it out of the printer.
-
Page 15: Control Panel Messages
Messages Description face up, or you have loaded a Form Feed The printer is feeding paper. transparency other than EPSON Color Laser Ready The printer is ready to print. Transparencies. The printer stops loading to prevent Reset The printer's current interface printer damage. - Page 16 Messages Description Messages Description Collate was Printing by specifying the Format Error An unformatted ROM has disabled number of copies is no longer ROM A/Format been inserted. If the ROM has possible due to lack of memory Error ROM B been formatted, but is or free space on the Hard Disk unreadable, format the ROM...
- Page 17 Messages Description Messages Description Image Optimum There is insufficient memory to Invalid HDD A fatal error occurred on the print the page at the specified Hard Disk Drive. Replace with a print quality. The printer normal Hard Disk Drive. automatically lowers the print Invalid PS3 A PostScript 3 ROM module quality so that it can continue...
- Page 18 Messages Description Messages Description Mem Overflow The printer has insufficient Paper Out XXX There is no paper in the memory to execute the YYYY specified paper source (XXX). current task. To correct the Load paper of the indicated XXX: error, press the Continue size (YYYY) into the source.
- Page 19 Messages Description Messages Description Print Overrun The required time to process Replace Waste T The waste toner collector has the print data exceeds the become full. Replace it with a print engine speed because new waste toner collector. the current page is too Service req A controller error or a print complex.
- Page 20 You have installed a Photoconductor photoconductor unit that has not been designed for this printer. Turn off the printer, then remove the incorrect photoconductor unit and install one designed for this printer (S051061). Copyright © 1999 by SEIKO EPSON CORPORATION, Nagano, Japan...