Kenwood TK-3202 Service Manual page 4

TK-3202/3206
4. To switch the clone master to Clone mode, press and hold
the [PTT] and [side2] keys while turning the transceiver
power ON.
5. Wait for 2 seconds. The LED will light orange and the
transceiver will announce "Clone".
6. Select the same channel table number as the clone slave/s.
7. Press [PTT] on the clone master to begin data transmission.
When the clone slave starts to receive data, the LED will
light green.
When the clone master finishes sending data, a
"confirmation" tone will sound.
If data transmission fails while cloning, an "error" tone will
sound from the Slave unit.
8. If the cloning fails, no data will be available in the Slave unit
when it is returned to User mode.
9. When the cloning is successful, the Slave unit's "Scan" and
"Key lock" functions will return to their default values (Scan
= OFF, Key lock = OFF).
Notes:
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceivers Clone Mode is configured as "Disabled",
the transceiver cannot enter Clone mode.
• The table shown below will cover the frequency tables used
for wireless cloning.
• Clone mode cannot be entered in battery low state.
• A unit cannot be a "Master Unit" if it is unprogrammed. If
[PTT] is pressed, an "error" tone will sound.
• The language used in cloning depends on the "Model type"
setting, not the FPU setting. C, C2, C5 and C6 type
TK-3207 transceivers will use Chinese. Other types English.
• Once a unit is set to be the Master, it cannot be a slave
after the data has been transmitted. This protects the data
in the Master unit.
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personnel.
• The Clone mode setting must be configured as "Disable"
before being delivered to the end-user.
• To clone, replace the antenna from both the master
transceiver and the slave transceiver with a dummy
load.
• The transmit output power is automatically set to Low
in Clone mode.
4
REALIGNMENT
Clone Frequency Table
MODEL
Type
Operating
Clone Frequency
Frequency (MHz)
Table
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
TK-3202
K,M K2,M2 M
450~490 470~512 450~490
450.000 472.000 450.000
452.000 474.000 452.000
454.000 476.000 454.000
456.000 478.000 456.000
458.000 480.000 458.000
460.000 482.000 460.000
462.000 484.000 462.000
464.000 486.000 464.000
466.000 488.000 466.000
468.000 490.000 468.000
470.000 492.000 470.000
472.000 494.000 472.000
474.000 496.000 474.000
476.000 498.000 476.000
478.000 500.000 478.000
480.000 502.000 480.000
482.000 504.000 482.000
484.000 506.000 484.000
486.000 508.000 486.000
488.000 510.000 488.000
TK-3206
M3
400~430
400.000
401.000
402.000
403.000
404.000
405.000
406.000
407.000
408.000
409.000
410.000
411.000
412.000
413.000
414.000
415.000
416.000
417.000
418.000
419.000