Front Glass Enclosure Panel, Removal And Installation; Logs, Vermiculite & Ember Placement - Lennox MPB35ST-NM-B Care And Operation Instructions Manual

Merit plus series mpb b-vent see-through gas fireplaces
Hide thumbs Also See for MPB35ST-NM-B:
Table of Contents

Advertisement

Front Glass Enclosure Panel, Removal
and Installation
WARNING
• Do not attempt to substitute the
materials used on this door,
or replace cracked or broken
glass.
• Handle this glass with extreme
care! Glass is susceptible to
damage – Do not scratch or
handle roughly while reinstall-
ing the glass door frame.
• The glass door(s) of this appli-
ance must only be replaced as
a complete unit as provided
by the manufacturer. Do not
attempt to replace broken,
cracked or chipped glass sepa-
rately.
• Do not attempt to touch the
front enclosure glass with your
hands while the fireplace is in
use.
WARNING
Do not operate appliance with
the glass front removed, cracked
or broken.
AVERTISSEMENT
Ne pas utiliser l'appareil si le
panneau frontal en verre n'est
pas en place, est craqué ou
brisé.
WARNING
Any safety screen or guard
removed for servicing the appli-
ance must be replaced prior to
operating the appliance.
AVERTISSEMENT
Tout écran ou protecteur retiré
pour permettre l'entretien de
l'appareil doit être remis en
place avant de mettre l'appareil
en marche.
12
Only doors certified with the appliance
shall be used.
Seules des portes certifiées pour cet
appareil doivent être utilisées.
WARNING: DO NOT abuse glass door by
striking or slamming shut.
These fireplaces are designed to operate only
with the glass enclosure panels properly
installed. Generally the glass enclosure panels
should not be removed except to gain access
to the components within the firebox, and the
appliance may only be operated without the
front glass enclosure panel in place for very
brief periods of time during initial appliance
checkout and adjustment.
Removing Glass Enclosure Panels
(see Figure 6)
1.
panel by pulling it out and off.
2. Open the control compartment access panel
by actuating the spring-loaded magnetic
catches securing the panel (gently depress
the outer top corners of the louvered or
radiant panel until the catches "pop" the door
free, allowing it to swing out and down to
the open position).
3. Locate the two (2) latches at the top of the
control compartment. To disengage the two
latches from the bottom vee-flange of the
glass enclosure panel, reach for the handles
located towards the back of the latches and
pull the handles down toward the front of
the appliance.
4. Swing the bottom of the door out and raise
it slightly to lift the top flange of the door
frame away from the appliance.
Installing Glass Enclosure Panels
(see Figure 6)
1. Visually inspect the gasket on the backside
of the panels. The gasket surface must be
clean, free of irregularities and seated firmly.
2. Position the glass enclosure panel in front
of the firebox opening at a 45 degree angle
and engage the top flange over the lip at the
top of the firebox opening. See Figure 6.
3. Swing the glass enclosure panel down and
back. Ensure the gasket seats evenly as the
panel draws shut. Engage the Vee-flange at
the bottom of the panel with the latches and
close the latches to secure the panel.
4. Close the bottom control compartment
access panel.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Lower Compartment
Top Flange
Door & Hinge
Glass Door
Bottom Vee-flange
Glass Door
Glass Door Latch
NOTE: When installing the glass door, ensure
the spacing on both sides are equal.
Figure 6
Remove the top louver assembly or radiant
Installing Grate, Vermiculite, Glowing
Embers And Logs
WARNINGS
• DO NOT attempt to install the
logs until the appliance instal-
lation has been completed, the
gas line connected and tested
for leaks and the initial burner
operation has been checked
out.
• The size and position of the log
set was engineered to give the
appliance a safe, reliable and
attractive flame pattern. Any
attempt to use a different log
set in the fireplace will void
the warranty and will result in
incomplete combustion, soot-
ing, and poor flame quality.
• Logs get very hot and will
remain hot up to one hour after
gas supply is turned off. Handle
only when logs are cool. Turn
off all electricity to the appli-
ance before you install grate,
volcanic stone, vermiculite,
embers and logs.
Glass Door
(Enclosure Panel)
Firebox Floor

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents