Page 2
INTRODUCTION Our Amplifiers provide high-performance sound reinforcement for your mobile audio equipment. Its versatility enables compatibility with optional Equalizers, Frequency Dividing Crossover Networks, and other audio processors in a customized system. The Multi-Mode bridging capabilities allow flexibility in hosting several dif- ferent speaker configurations.
TABLE OF CONTENTS PLANNING YOUR SYSTEM ..............3 WIRING CONNECTION ................. PANEL LAYOUT ................... CONTROL FUNCTIONS ............6, 7 SPEAKER CONNECTION 4 CHANNEL CONFIGURATION ....8-10 TROUBLE SHOOTING GUIDE .............. 11 SPECIFICATION ..................12 WARNING....................PLANNING YOUR SYSTEM Before beginning the installation, consider the following:...
CONNECTING THE POWER CAUTION: AS A PRECAUTION, DISCONNECT THE POWER WIRE FROM THE BATTERY WHILE MAKING POWER AND GROUND CONNECTIONS TO THE AMPLIFIER. 10 GAUGE(Thicker if planning for additional Amplifiers) wire recommended for both the power and ground wires. 10 Gauge, for the remote turn-on wire. Both types are available at most Mobile Audio Dealers or Installation Shop.
CONTROL FUNCTIONS RCA input jacks These RCA input jacks are for with source units that have RCA or Line level outputs. A source unit with a minimum level of 180m V is required for proper operation. high quality twisted pair cables is recommended to decrease...
CONTROL FUNCTIONS 7. SPEAKERS Connect subwoofers to these tenninals. AQA430SL AQA430WT GRAY GREEN/BLACK WHITEJBLACK~ PURP WHITE~ PURPLE/BLACK GRAY/BLACK GREEN 8.GND Connect this tenninal directly to the sheet metal chassis of the vehicle, using the shortest wire necessary to make this connection. Always use wire of the same gauge or larger than the (+) 12 volt power wire.
Page 8
4CHANNEL STEREO CONFIGURATION for AQA430SL AQA430wr • ---· _ 04 3685 -12d8 (QJl2SJ • _{jff)CD CD CD CD CD HIGH INPUT • "" 2·8 Ohms 2-8 Ohms Ohms 2-8 Ohms Channel and channel 3/4 lowest recommended impedance is 20hm stereo.
Page 9
4CHANNEL BRIDGED CONFIGURATION for AQA430SL AQA430wr ---· 12J16l • _ 04'12dB3685 ~(jJj) CDCDmCDmCD "" 4-8 Ohms 4-8 Ohms 1CH/2CH 3CH/4CH Channel 112 and outputs can configured high.pass, lowpass, full range operation. 2. Channel outputs are configured for summed bridged operation subwoofer.
Page 10
4CHANNEL TRI MODE CONFIGURATION for AQA430SL AQA430wr • ---· ISZ1I2SI • _ 04· 3685 12dB SPEAII;ER GAIN ~.IQl .IQl~ HIGH INPUT LPf FUll HPF 50Hz sootil FUll HPF 50Hz SOOH. (1/X111 IJI4CII) $lOte$4CH9 X-oVER X-oVER "" CAPACITOR HIGH PASS FILTER 2-8 Ohms 2·8 Ohms...
TROUBLE SHOOTING GUIDE Check fuses in amplifier. Be sure Turn-on lead is connected No power to power wire Repair power wire or connections Check connections to radio Inspect for short circuit or an open connect ion. Reverse Left and Right inputs to determine it is...
SPECIFICATIONS AQA430SL AQA430wr MODEL# MAXIMUM POWER OUTPUT 1600W POWER OUTPUT@40hm 300WX4CH POWER OUTPUT@20hm 600WX4CH BRIDGED POWER @40hm 1200Wx2CH O.05%THD+N FREQUENCY RESPONSE -1.OdB 20Hz-40KHz 50-500Hz 50-500Hz ADJUSTABLE SENSITIVITY RANGE 180mV INPUT IMPEDANCE (LOW LEVEL) FUSE 40AX 1.73 X 6.22 8.03 DIMENSION(Hx W x...