Page 1 2013 E-SERIES fordowner.com ford.ca DC2J 19A321 AA May 2013 Third Printing Owner’s Manual E-Series Litho in U.S.A.
Page 2: Table Of Contents
Table of Contents Introduction Child Safety Child seat positioning ........19 Booster seats .
Page 3 Table of Contents Lighting Lighting control ........69 Instrument lighting dimmer.
Page 4: Table Of Contents
Table of Contents Fuel and Refueling Fuel quality .........116 Running out of fuel.
Page 5 Table of Contents Towing Trailer towing........154 Trailer brake controller-integrated .
Page 6: Table Of Contents
Table of Contents Washer fluid check ........216 Changing the vehicle battery .
Page 7 Upfitter controls ........290 Ford Extended Service Plan Audio System AM/FM stereo.
Page 8: Table Of Contents
Errors and omissions excepted. © Ford Motor Company 2013 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013...
Page 9: Introduction
Introduction ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time to get to know your vehicle by reading this manual. The more that you know about it, the greater the safety and pleasure you will get from driving it.
Page 10 Introduction SYMBOL GLOSSARY WARNING: You risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol. These are some of the symbols you may see on your vehicle. Symbol Description Symbol Description Symbol Description Safety alert...
Page 11 In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may...
Page 12 EDR. Ford Motor Company and Ford of Canada do not access event data recorder...
Page 13 If you do not want Ford or its vendors to receive this information, do not activate the service. Ford Motor Company and the vendors it uses to provide you with this information do not store your vehicle travel information.
Page 14 Introduction FORD CREDIT (U.S. ONLY) Ford Credit offers a full range of financing and lease plans to help you acquire your vehicle. If you have financed or leased your vehicle through Ford Credit, thank you for your business. For your convenience, we offer a number of ways to contact us, as well as help manage your account.
Page 15 Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual, Ford Truck Body Builder’s Layout Book and the...
Page 16 Introduction Use of your Ford light truck as an ambulance, without the Ford Ambulance Preparation Package voids the Ford New Vehicle Limited Warranty and may void the Emissions Warranties. In addition, ambulance usage without the preparation package could cause high underbody temperatures, overpressurized fuel and a risk of spraying fuel which could lead to fires.
Page 17 Introduction EXPORT UNIQUE (NON–UNITED STATES/CANADA) VEHICLE SPECIFIC INFORMATION For your particular global region, your vehicle may be equipped with features and options that are different from the features and options that are described in this owner’s manual. A market unique supplement may be supplied that complements this book.
Page 18: Child Safety
NHTSA and other safety organizations, or are the minimum requirements of law. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) and consulting your pediatrician to make sure your child seat is appropriate for your child, and is compatible with and properly installed in your vehicle.
Page 19 Child Safety Recommendations for Safety Restraints for Children Child size, height, weight, or Recommended restraint type Infants or Children weighing 40 lb (18 kg) or Use a child safety seat toddlers less (generally age four or (sometimes called an younger). infant carrier, convertible seat, or toddler seat).
Page 20: Child Seat Positioning
Child Safety CHILD SEAT POSITIONING WARNING: Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat upon which the child seat is installed all the way back.
Page 21 Child Safety WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash. WARNING: To avoid risk of injury, do not leave children or pets unattended in your vehicle.
Page 22: Booster Seats
Child Safety BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the risk of injury or death in a crash.
Page 23 Child Safety Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield. If a vehicle seating position has a low seat back or no head restraint, a backless booster seat may place your child’s head (as measured at the tops of the ears) above the top of the seat.
Page 24 Child Safety If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition. Do not introduce any item thicker than this under the booster seat.
Page 25: Installing Child Seats
Child Safety INSTALLING CHILD SEATS Child Seats Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers or children weighing 40 pounds (18 kilograms) or less (generally age four or younger). Using Lap and Shoulder Belts WARNING: Airbags can kill or injure a child in a child seat.
Page 26 Child Safety When installing a child safety seat with combination lap and shoulder belts: • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Page 27 Child Safety 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until...
Page 28 There should be no more than 1 inch (2.5 centimeters) of movement for proper installation. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician to make certain the child restraint is properly installed.
Page 29 Child Safety Using Lower Anchors and Tethers for CHildren (LATCH) WARNING: Never attach two child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
Page 30 Child Safety Your vehicle has LATCH lower anchors, top tether anchors, or both at the following locations: • Five passenger crew van • Seven passenger wagon • Eight passenger wagon 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 31 Child Safety • Eleven passenger wagon • Twelve passenger wagon • Fifteen passenger wagon 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 32 Child Safety The LATCH lower anchors are located at the rear section of the rear seat between the cushion and seatback. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. Follow the instructions on attaching child safety seats with tether straps.
Page 33 Child Safety Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. Note: If you install a child seat with rigid LATCH attachments, and have attached the top tether strap to the proper top tether anchor, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it.
Page 34 Child Safety 3. Clip the tether strap hook to the seat pedestal at the location shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a crash. 4. Adjust the front passenger seat to the full rearward position.
Page 35 If the safety seat is not anchored properly, the risk of a child being injured in a crash greatly increases. If your child restraint system is equipped with a tether strap, and the child restraint manufacturer recommends its use, Ford also recommends its use. 2013 Econoline (eco)
Page 36: Safety Belts
Safety Belts PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seat back upright and the lap belt snug and low across the hips. WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a crash.
Page 37 Safety Belts WARNING: When possible, all children 12 years old and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death. WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather;...
Page 38: Fastening The Safety Belts
Safety Belts FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in your vehicle are combination lap and shoulder belts. 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch.
Page 39 Safety Belts Pregnant women should always wear their safety belts. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow. The shoulder belt should be positioned to cross the middle of the shoulder and the center of the chest.
Page 40 Safety Belts Automatic Locking Mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to Use the Automatic Locking Mode This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions.
Page 41: Safety Belt Height Adjustment
Safety Belts SAFETY BELT HEIGHT ADJUSTMENT WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a crash. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder.
Page 42: Safety Belt-Minder
Safety Belts SAFETY BELT-MINDER® This feature supplements the safety belt warning function by providing additional reminders by intermittently sounding a chime and illuminating the safety belt warning light when the driver’s seat is occupied and the safety belt is unbuckled. If...
Page 43 Safety Belts Deactivating and Activating the Belt-Minder® Feature WARNING: While the design allows you to deactivate your Belt-Minder, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the Belt-Minder system activated for yourself and others who may use the vehicle.
Page 44: Child Restraint And Safety Belt Maintenance
Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced. However, if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Page 45: Supplementary Restraints System
Supplementary Restraints System PRINCIPLES OF OPERATION WARNING: Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module. WARNING: All occupants of your vehicle, including the driver, should always properly wear their safety belts, even when an airbag supplemental restraint system is provided.
Page 46 Supplementary Restraints System The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see a cloud of harmless powdery residue if an airbag deploys.
Page 47: Driver And Passenger Airbags
Supplementary Restraints System DRIVER AND PASSENGER AIRBAGS WARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury.
Page 48 Supplementary Restraints System Proper Driver and Front Passenger Seating Adjustment WARNING: The National Highway Traffic Safety Administration recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbag module. Failure to follow this could seriously increase the risk of injury or death.
Page 49 Supplementary Restraints System Passenger Airbag ON and OFF Switch (If Equipped) WARNING: An airbag ON and OFF switch may have been installed in this vehicle. Before driving, always look at the face of the switch to be sure the switch is in the proper position in accordance with these instructions and warnings.
Page 50 Supplementary Restraints System Turning the Passenger Airbag Back On WARNING: The safety belts for the driver and right front passenger seating positions have been specifically designed to function together with the airbags in certain types of crashes. When you turn off your airbag, you not only lose the protection of the airbag, you also may reduce the effectiveness of your safety belt system, which was designed to work with the airbag.
Page 51 Supplementary Restraints System The passenger side airbag should always be on (the airbag OFF light should not be illuminated) unless the passenger is a person who meets the requirements stated either in Category 1, 2 or 3 of the National Highway Traffic Safety Administration/Transport Canada deactivation criteria which follows.
Page 52 Supplementary Restraints System 1. Infant. An infant (less than 1 year old) must ride in the front seat because: • the vehicle has no rear seat; • the vehicle has a rear seat too small to accommodate a rear-facing infant seat; or •...
Page 53 Supplementary Restraints System Transport Canada Deactivation Criteria (Canada Only) WARNING: This vehicle has special energy management safety belts for the driver and right front passenger. These particular belts are specifically designed to work with airbags to help reduce the risk of injury in a crash. The energy management safety belt is designed to give or release additional belt webbing in some accidents to reduce concentration of force on an occupant’s chest and reduce the risk of certain bone fractures and injuries to underlying organs.
Page 54: Crash Sensors And Airbag Indicator
Supplementary Restraints System CRASH SENSORS AND AIRBAG INDICATOR WARNING: Modifying or adding equipment to the front end of your vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of your vehicle.
Page 55: Airbag Disposal
Supplementary Restraints System The fact that the safety belt pretensioners or airbags did not activate in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (such as crash severity, belt usage) were not appropriate to activate these safety devices.
Page 56: Keys And Remote Control
Keys and Remote Control GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 57: Remote Control
Keys and Remote Control REMOTE CONTROL (IF EQUIPPED) If there are problems with the remote entry system, make sure to take all remote entry transmitters with you to the authorized dealer in order to aid in troubleshooting the problem. Note: If the vehicle is equipped with the E-Guard Cargo Protection System™...
Page 58: Replacing A Lost Key Or Remote Control
Keys and Remote Control 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery. 4. Insert the new battery. Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery.
Page 59 Keys and Remote Control Reprogramming Your Remote Controls You must have all remote controls (maximum of four) available before beginning this procedure. If all remote controls are not present during programming, the ones missing will no longer operate the vehicle. Note: Make sure you do not press the brake pedal during this sequence.
Page 60: Locks
Locks LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lock and unlock your vehicle. Power Door Locks (If Equipped) The power door lock control is located on the driver and front passenger door panels.
Page 61 Locks Autolock and Unlock Note: Your vehicle comes with this feature disabled. The autolock feature will lock all the doors when: • all doors are closed, • the ignition is on, • you shift into any gear putting the vehicle in motion, and •...
Page 62 Locks Illuminated Entry The interior lamps and parking lamps illuminate when the remote entry system is used to unlock the doors or sound the personal alarm. The illuminated entry system will turn off the lights if: • you switch the ignition on •...
Page 63 Locks System Procedure – Power Door Locks • Lock the vehicle with the key, manual door lock, remote control or use the power door lock on the front door trim panel. The front doors are locked and the cargo doors are double-locked. •...
Page 64 Locks The emergency handles are located in the following areas: • The side door emergency handle is located on the door inner trim panel in the speaker cup. • The rear door handle is located in the rear door below the glass. To open the side or rear cargo doors from the inside: 1.
Page 65: Security
Security SECURILOCK® PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting issues if they are too close to the key when starting the engine.
Page 66 Security Replacement Keys If your keys are lost or stolen and you do not have an extra coded key, you will need to have your vehicle towed to an authorized dealer. The key codes need to be erased from your vehicle and new coded keys will need to be programmed.
Page 67 Security If the key has been successfully programmed it will start the vehicle’s engine. The theft indicator light will illuminate for three seconds and then go out. If the key was not successfully programmed, it will not start your vehicle’s engine and the theft indicator light will flash rapidly. Wait 20 seconds and repeat Steps 1 through 8.
Page 68: Steering Wheel
Steering Wheel ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. 1. Pull and hold the steering wheel release lever. 2. Adjust the steering wheel to the desired position then release the lever. VOICE CONTROL (IF EQUIPPED) A.
Page 69: Wipers And Washers
Wipers and Washers WINDSHIELD WIPERS Note: Fully defrost the windshield before turning on the windshield wipers. Note: Make sure the windshield wipers are turned off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears.
Page 70: Lighting
Lighting LIGHTING CONTROL The first position turns the lamps off. The second position turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. The third position turns the headlamps on. High Beams • Push the lever toward the instrument panel to activate.
Page 71: Instrument Lighting Dimmer
Lighting INSTRUMENT LIGHTING DIMMER Note: If you disconnect the battery or it becomes discharged, the dimmer switch will require re-calibration. Rotate the dimmer switch from the full dim position to the full dome/on position to reset. Note: Move the control to the full upright position, past detent, to turn on the interior lamps.
Page 72: Turn Signal Control
Lighting TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Dome Lamps with Rear Headliner (If Equipped) Dome lamps equipped with an on/off control will light when: •...
Page 73 Lighting Front and Rear Courtesy/Reading Lamps (If Equipped) The dome portion of the lamp, the center light, will light when: • any door is opened • panel dimmer control is moved to the full upright position past the detent The reading lamp portion, the two outer lights, can only be toggled on and off at the lamp.
Page 74: Windows And Mirrors
Windows and Mirrors POWER WINDOWS (IF EQUIPPED) WARNING: Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the proximity of the window openings.
Page 75: Exterior Mirrors
Windows and Mirrors EXTERIOR MIRRORS Power Exterior Mirrors (If Equipped) WARNING: Do not adjust the mirror while your vehicle is in motion. A. Left mirror B. Off C. Right mirror To adjust your mirrors: 1. Select the mirror you want to adjust. 2.
Page 76 Windows and Mirrors On Standard Mirror You can tilt the spotter mirror up or down to increase visibility. Only apply pressure to the center of the top or bottom edges when adjusting the mirror. Note: Do not apply any force to the left or right edges.
Page 77: Interior Mirrors
Windows and Mirrors The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A).
Page 78: Sun Visors
Windows and Mirrors Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when bright lights are detected from behind your vehicle.
Page 79: Instrument Cluster
Instrument Cluster GAUGES Cluster shown in standard measure. Metric similar. A. Tachometer B. Fuel gauge C. Engine coolant temperature gauge D. Speedometer E. Battery voltage gauge F. Information display. See Information displays for more information. G. Engine oil pressure gauge Fuel Gauge Indicates approximately how much fuel is left in the fuel tank (when the ignition is on).
Page 80: Warning Lamps And Indicators
Instrument Cluster Engine Coolant Temperature Gauge Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. If the engine coolant temperature exceeds the normal range, stop the vehicle as soon as safely possible, switch off the engine and let the engine cool. WARNING: Never remove the coolant reservoir cap while the engine is running or hot.
Page 81 Instrument Cluster Airbag – Front If it fails to illuminate on startup, continues to flash or remains on, it indicates a malfunction. Have the system checked by your authorized dealer. A chime will sound when there is a malfunction in the indicator light. Anti-Lock Braking System If it illuminates when you are driving, this indicates a malfunction.
Page 82 Instrument Cluster Charging System It will illuminate when the 12–volt battery is not charging properly. Contact your authorized dealer as soon as possible. This indicates a problem with the electrical system or a related component. Check Fuel Cap Displays when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service Engine Soon warning light to come on.
Page 83 Instrument Cluster Low Fuel Level It will illuminate when the fuel level is low or near empty. Refuel as soon as possible. Low Tire Pressure Warning It will illuminate when your tire pressure is low. If the lamp remains on with the engine running or when driving, check your tire pressure as soon as possible.
Page 84: Audible Warnings And Indicators
Instrument Cluster WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Stability Control System Displays when the AdvanceTrac®/Traction control is active. If the light remains on, have the system serviced immediately.
Page 85: Information Displays
Information Displays GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 86 Information Displays System Check and Vehicle Feature Customization Note: When returning to the setup menu and a non-English language has been selected, HOLD RESET FOR ENGLISH will be displayed to change back to English. Press and hold the SELECT/RESET stem to change back to English.
Page 87 Information Displays • OIL LIFE XXX% HOLD RESET = NEW: This displays the remaining oil life. An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change, perform the following: 1.
Page 88 Information Displays Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Press and release the SELECT/RESET stem to scroll through the information displays until the message center displays HOLD RESET FOR SETUP MENU.
Page 89 Information Displays 3. Press and hold the SELECT/RESET stem for approximately two seconds until the message center enters the compass zone adjustment mode. 4. Press and hold the SELECT/RESET stem until the message center displays CIRCLE SLOWLY TO CALIBRATE. 5. Slowly drive the vehicle in a circle less than 3 mph (5 km/h ) until the CIRCLE SLOWLY TO CALIBRATE message changes to CALIBRATION COMPLETED.
Page 90: Information Messages
Information Displays INFORMATION MESSAGES Press the SELECT/RESET stem to acknowledge and remove some messages from the information display. Other messages will be removed automatically after a short time. Certain messages need to be confirmed before you can access the menus. AdvanceTrac®...
Page 91 Information Displays Park Aid Messages Action / Description CHECK REAR PARK Displayed when the transmission is in R (Reverse) and the park aid is disabled. Tire Messages Action / Description LOW TIRE Displays when one or more tires on your vehicle have low tire pressure.
Page 92 Information Displays Trailer Messages Action / Description TRAILER BRAKE Displayed and accompanied by a single chime, in response to faults sensed by the TBC. Refer MODULE FAULT to Trailer towing in the Towing chapter for more information. TRAILER Displayed when a correct trailer connection (a trailer with electric trailer brakes) is sensed CONNECTED during a given ignition cycle.
Page 93: Climate Control
Climate Control HEATER ONLY SYSTEM VENT COOL WARM A. Fan speed control: Controls the volume of air circulated in your vehicle. Adjust to select the desired fan speed or switch off. If you switch the fan off, the windshield may fog up. B.
Page 94 Climate Control MANUAL CLIMATE CONTROL VENT NORM COOL WARM A. Fan speed control: Controls the volume of air circulated in your vehicle. Adjust to select the desired fan speed or switch off. If you switch the fan off, the windshield may fog up. B.
Page 95 Climate Control Select to distribute air through the windshield air vents. You can also use this setting to defog and clear the windshield of a thin covering of ice. You can also increase the temperature and fan speed to improve clearing. REAR FAN SPEED CONTROL (IF EQUIPPED) REAR Controls the volume of air circulated in the rear of your vehicle.
Page 96 Climate Control Recommended Settings for Heating Adjust the fan speed to the second speed setting. Adjust the temperature control to the midway point of the hot settings. Adjust the air distribution control to MIX. Cooling the Interior Quickly Adjust the fan speed to the highest speed setting initially, then adjust to the desired comfort level.
Page 97 Climate Control Maximum Cooling Performance in Instrument Panel or Instrument Panel and Floor Positions Adjust the temperature control to the lowest setting. Adjust the fan speed to the highest setting initially and then adjust it to suit the desired comfort level. 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 98: Seats
Seats SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the passenger sensing system, resulting in serious injury or death in a crash. Always sit upright against your seat back, with your feet on the floor.
Page 99: Head Restraints
Seats Make sure that your driving position is comfortable and that you can maintain full control of your vehicle. HEAD RESTRAINTS WARNING: To minimize the risk of neck injury in the event of a crash , the driver and passenger occupants should not sit in and operate the vehicle until the seat back is placed in its proper position.
Page 100 Seats Moving the Seats Backward and Forward (If Equipped) Recline Adjustment (If Equipped) WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seat back to its original position, pull on the seatback to make sure that it has fully latched.
Page 101: Power Seats
Seats POWER SEATS WARNING: Never adjust the driver’s seat when the vehicle is moving. The control is located on the outboard side of the seat cushion. Press A to raise or lower the front portion of the seat cushion. Press B to move the seat forward, backward, up or down.
Page 102 Seats Quick-Release Captains Chair (Seven Passenger Configuration-Second Row Only) WARNING: Check to see that the seat and seat back is latched securely in position. Keep floor area free of objects that would prevent proper seat engagement. Never attempt to adjust the seat while the vehicle is in motion.
Page 103 Seats To install the seat: 1. Position the seat to the floor mount. 2. Pull the seat latch handle downward to lock the seat in position. 3. Make sure the safety belt is not twisted. Then, insert the safety belt tongue into the detachable anchor until it is securely fastened and you feel the latch engage.
Page 104 Seats 3. Clip the end of the belt to the stationary portion of the shoulder belt coming out of the trim panel. The end of the shoulder belt must be clipped in order to keep it from striking anything during vehicle operation.
Page 105 Seats To install the seat: 1. Make sure the floor striker area is clean of any debris that would prevent the seat from latching. 2. With assistance, position the seat in the vehicle. 3. Align the front hooks to the front striker pins prior to lowering the rear latch mechanism and aligning them with the rear striker pins.
Page 106: Auxiliary Power Points
Auxiliary Power Points AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury. Note: If used when the engine is not running, the battery will discharge.
Page 107 Auxiliary Power Points 110 Volt AC Power Point (If Equipped) WARNING: Do not keep electrical devices plugged in the powerpoint whenever the device is not in use. Do not use any extension cord with the 110 volt AC power point, since it will defeat the safety protection design.
Page 108 Auxiliary Power Points The power point can provide power whenever the ignition is on and the indicator light is on. The indicator light is located in the top left corner of the power point. When the indicator light is: • on — power point is ready to supply power •...
Page 109: Starting And Stopping The Engine
Starting and Stopping the Engine GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover.
Page 110: Ignition Switch
Starting and Stopping the Engine IGNITION SWITCH Note: Do not store the key in the ignition after the vehicle is turned off and you have left the vehicle. This could cause a drain on the battery. A. Accessory: Allows the electrical accessories, such as the radio, to operate while the engine is not running.
Page 111 Starting and Stopping the Engine Vehicles with an Ignition Key Note: Do not touch the accelerator pedal. 1. Fully press the brake pedal. 2. Turn the key to the start position. Release the key when the engine starts. Note: The engine may continue cranking for up to 15 seconds or until it starts.
Page 112 Starting and Stopping the Engine Fast Restart (Vehicles with Keyless Start) The fast restart feature allows you to restart the engine within 20 seconds of switching it off, even if a valid key is not present. Within 20 seconds of switching the engine off, press the brake pedal and press the button.
Page 113 Starting and Stopping the Engine 1. If your vehicle has an ignition key, move the transmission selector lever to position N and use the brakes to bring your vehicle to a safe stop. When your vehicle has stopped, move the transmission selector lever to position P and turn the key to the off position.
Page 114: Engine Block Heater
Starting and Stopping the Engine Guarding Against Exhaust Fumes WARNING: If you smell exhaust fumes inside your vehicle, have this checked immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects.
Page 115 Starting and Stopping the Engine • Make sure that when in operation, the extension cord plug and the heater cord plug connections are free and clear of water. This could cause an electric shock or fire. • Make sure your vehicle is parked in a clean area, clear of combustibles.
Page 116: Fuel And Refueling
Fuel and Refueling SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops.
Page 117: Fuel Quality
Fuel and Refueling • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.
Page 118: Running Out Of Fuel
Fuel and Refueling Octane Recommendations Regular unleaded gasoline with a pump (R+M)/2 octane rating of 87 is recommended. Some stations offer fuels posted as “Regular” with (R+M)/2 METHOD an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended.
Page 119: Refueling
Fuel and Refueling REFUELING WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island. • Turn off your engine when you are refueling. •...
Page 120: Fuel Consumption
Ford, Motorcraft® or other certified fuel filler cap is not used. Your fuel tank filler cap has an indexed design with a 1/4 turn on/off feature.
Page 121 Fuel and Refueling For consistent results when filling the fuel tank: • Turn the ignition off before fueling; an inaccurate reading results if the engine is left running. • Use the same fill rate (low–medium–high) each time the tank is filled. •...
Page 122 Information are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft® or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 123 Fuel and Refueling On-board Diagnostics (OBD-II) Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the on-board diagnostics system (OBD-II). The OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
Page 124 Fuel and Refueling Readiness for Inspection/Maintenance (I/M) Testing Some state, provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. If the service engine soon indicator is on or the bulb does not work, the vehicle may need to be serviced.
Page 125: Transmission
Transmission AUTOMATIC TRANSMISSION OPERATION Understanding the Gearshift Positions of the 4–Speed Automatic Transmission WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the lock position and remove the key whenever you leave your vehicle. Your vehicle has been designed to improve fuel economy by reducing fuel usage during coasting or deceleration.
Page 126 Transmission R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll.
Page 127 Transmission Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF lamp is illuminated. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to other gears.
Page 128 Transmission Understanding the Shift Positions of the 5–Speed Automatic Transmission (If Equipped - 5.4L and 6.8L Gasoline Engines Only) WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the lock position and remove the key whenever you leave your vehicle.
Page 129 Transmission N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive with Overdrive) with Tow/Haul off D (Overdrive) with tow/haul off is the normal driving position for the best fuel economy.
Page 130 Transmission 3 (Third) Transmission starts and operates in third gear only. Used for improved traction on slippery roads. Selecting 3 (Third) provides engine braking. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional engine braking on downgrades. 1 (First) •...
Page 131 Transmission If you cannot move the gearshift lever out of P (Park) with the ignition in the on position and the brake pedal pressed, it is possible that a fuse has blown or the vehicle’s brake lamps are not operating properly. Refer to Fuses chapter.
Page 132 Transmission Automatic Transmission Adaptive Learning This feature is designed to increase durability and provide consistent shift feel over the life of the vehicle. A new vehicle or transmission may have firm shifts, soft shifts or both. This operation is considered normal and will not affect function or durability of the transmission.
Page 133: Brakes
Brakes GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn out. Have them inspected by an authorized dealer. If your vehicle has continuous vibration or shudder in the steering wheel while braking, have your vehicle inspected by an authorized dealer.
Page 134: Hints On Driving With Anti-Lock Brakes
Brakes HINTS ON DRIVING WITH ANTI-LOCK BRAKES When the system is operating, the brake pedal will pulse and may travel further. Maintain pressure on the brake pedal. You may also hear a noise from the system. This is normal. The anti-lock braking system will not eliminate the dangers inherent when: •...
Page 135: Traction Control
Traction Control PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss of traction. If your vehicle begins to slide, the system applies the brakes to individual wheels and, when needed, reduces engine power at the same time. If the wheels spin when accelerating on slippery or loose surfaces, the system reduces engine power in order to increase traction.
Page 136: Stability Control
Stability Control PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction or wheel and tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceTrac® system. In addition, installing any stereo loudspeakers may interfere with and adversely affect the AdvanceTrac®...
Page 137 Stability Control A Vehicle without AdvanceTrac® with RSC® skidding off its intended route. B Vehicle with AdvanceTrac® with RSC® maintaining control on a slippery surface. 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 138 Stability Control USING ADVANCETRAC® WITH RSC® (IF EQUIPPED) The system automatically activates when you start your engine. The AdvanceTrac® with RSC® system cannot be completely turned off, but the electronic stability system and roll stability control portions of the system are disabled when the transmission is in position R. You can turn off the traction control portion of the system independently.
Page 139: Parking Aids
Parking Aids SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed) objects when moving in reverse on a flat surface at parking speeds. Traffic control systems, inclement weather, air brakes, and external motors and fans may also affect the function of the sensing system;...
Page 140: Rear-View Camera System
Parking Aids Using the Rear Sensing System The rear sensors are only active when the transmission is in R (Reverse). As the vehicle moves closer to the obstacle, the rate of the audible warning increases. When the obstacle is fewer than 10 inches (25 centimeters) away, the warning sounds continuously.
Page 141 Parking Aids WARNING: Back up as slow as possible since higher speeds might limit your reaction time to stop the vehicle. WARNING: Use caution when using the rear video camera and the liftgate is ajar. If the liftgate is ajar, the camera will be out of position and the video image may be incorrect.
Page 142 Parking Aids Note: When towing, the camera only sees what is being towed behind the vehicle. This might not provide adequate coverage as it usually provides in normal operation and some objects might not be seen. In some vehicles, the guidelines may disappear once the trailer tow connector is engaged.
Page 143 Parking Aids A. Rear bumper B. Fixed guideline: Red zone C. Fixed guideline: Yellow zone D. Fixed guideline: Green zone E. Centerline The fixed guidelines fade in and out depending on the steering wheel position. Always use caution while reversing. Objects in the red zone are closest to your vehicle and objects in the green zone are further away.
Page 144 Parking Aids Manual Zoom WARNING: When manual zoom is on, the full area behind the vehicle is not shown. Be aware of your surroundings when using the manual zoom feature. Note: Manual zoom is only available when the transmission is in R (Reverse).
Page 145: Cruise Control
Cruise Control PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your foot on the accelerator pedal. USING CRUISE CONTROL (IF EQUIPPED) WARNING: Do not use cruise control in heavy traffic, on winding roads or when the road surface is slippery. This could result in loss of vehicle control, serious injury or death.
Page 146 Cruise Control Changing the Set Speed Note: If you accelerate by pressing the accelerator pedal, the set speed will not change. When you release the accelerator pedal, you will return to the speed that you previously set. • Press and hold SET ACCEL to increase or COAST to decrease the set speed.
Page 147: Driving Aids
Driving Aids STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level (If the fluid level is below the MIN line mark on the dipstick).
Page 148: Load Carrying
Load Carrying LOAD LIMIT Vehicle Loading – With and Without a Trailer This section will guide you in the proper loading of your vehicle and/or trailer, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance.
Page 149 Load Carrying WARNING: The appropriate loading capacity of your vehicle can be limited either by volume capacity (how much space is available) or by payload capacity (how much weight the vehicle should carry). Once you have reached the maximum payload of your vehicle, do not add more cargo, even if there is space available.
Page 150 Load Carrying Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) –...
Page 151 Load Carrying GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label. The label shall be affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position.
Page 152 Load Carrying WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury. GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer.
Page 153 Load Carrying WARNING: Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than the original tires do not increase the GVWR and GAWR limitations.
Page 154 Load Carrying capacity in your vehicle to transport four friends and your golf bags. In metric units, the calculation would be: 635 kg - (5 x 99 kg) - (5 x 13.5 kg) = 635 - 495 - 67.5 = 72.5 kg. •...
Page 155: Towing
Towing TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury.
Page 156 Towing Note: Calculate the maximum trailer weight for all cutaway vehicles by subtracting the weight of your vehicle (including incomplete vehicle weight and payload, which includes second unit body weight, cargo and passengers) from the gross combined weight. Otherwise, maximum trailer weight is 10000 pounds (4536 kilograms).
Page 157 Towing Maximum GCWR Maximum trailer Engine Rear axle ratio - lb. (kg) weight - lb. (kg) E-150 Regular, Recreational and Crew van 4.6L 3.73 11500 (5216) 6000 (2722) 4.6L 4.10 12000 (5443) 6500 (2948) 5.4L 3.73 and 4.10 13000 (5897) 7500 (3402) E-150 Extended van 4.6L...
Page 158 Towing Maximum GCWR Maximum trailer Engine Rear axle ratio - lb. (kg) weight - lb. (kg) E-350 Regular wagon (11 and 12 passenger) 5.4L 3.73 and 4.10 13000 (5896) 6700 (3039) 6.8L 3.73 15000 (6804) 8500 (3856) 6.8L 4.10 18500 (8391) 10000 (4536) E-350 Extended wagon (11 passenger) 5.4L...
Page 159 Towing Maximum GCWR Maximum trailer Engine Rear axle ratio - lb. (kg) weight - lb. (kg) E-350 Stripped chassis dual rear wheel 158–inch and 176–inch wheelbase 5.4L 4.10 13000 (5897) 8300 (3765) 6.8L 4.10 18500 (8391) 10000 (4536) E-450 Cutaway 5.4L 4.56 14050 (6373)
Page 160 Towing Trailer Towing Connector (Vehicles with a Trailer Towing Package and 7–Pin Connector) When attaching the trailer wiring connector to your vehicle, only use a proper fitting connector that works with the vehicle and trailer functions. If your vehicle has a trailer towing package, it may have a 7–pin connector.
Page 161 Towing When hooking-up a trailer using a weight-distributing hitch, always use the following procedure: 1. Park the loaded vehicle, without the trailer, on a level surface. 2. Measure the height to the top of your vehicle’s front wheel opening on the fender. This is H1. 3.
Page 162: Trailer Brake Controller-Integrated
1500 pounds (680 kilograms) when loaded. Integrated Trailer Brake Controller (If Equipped) WARNING: The Ford TBC has only been verified to be compatible with trailers having electric-actuated drum brakes (one to four axles) and some electric-over-hydraulic (EOH) brakes. It will not activate hydraulic surge-style trailer brakes.
Page 163 Towing The controller shows gain setting, output bar graph, and trailer connectivity status in the information display. They appear in the information display as follows: • TBC GAIN = XX.X NO TRAILER: Shows the current gain setting during a given ignition cycle and when adjusting the gain. This also displays if you use the manual control lever or make gain adjustments with no trailer connected.
Page 164 Explanation of Information Display Warning Messages Note: An authorized dealer can diagnose the trailer brake controller to determine exactly which trailer fault has occurred. However, your Ford warranty does not cover this diagnosis if the fault is with the trailer.
Page 165 • The trailer brake controller is only a factory-installed or dealer-installed item. Ford is not responsible for warranty or performance of the controller due to misuse or customer installation. 2013 Econoline (eco)
Page 166 Towing Trailer Lamps WARNING: Never connect any trailer lamp wiring to the vehicle’s tail lamp wiring; this may damage the electrical system resulting in a fire. Contact an authorized dealer as soon as possible for assistance in proper trailer tow wiring installation. Additional electrical equipment may be required.
Page 167 Towing • If your vehicle is equipped with AdvanceTrac™ with RSC, this system may turn on during typical cornering maneuvers with a heavily loaded trailer. This is normal. Turning the corner at a slower speed while towing may reduce this tendency. •...
Page 168: Wrecker Towing
We recommend the use of a wheel lift and dollies or flatbed equipment to tow your vehicle. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Vehicle damage may occur if towed incorrectly, or by any other means.
Page 169: Recreational Towing
Towing TOWING THE VEHICLE ON FOUR WHEELS Emergency Towing If your vehicle becomes inoperable (without access to wheel dollies, car-hauling trailer, or flatbed transport vehicle), it can be flat-towed (all wheels on the ground, regardless of the powertrain and transmission configuration) under the following conditions: •...
Page 170: Driving Hints
Driving Hints PREPARING TO DRIVE WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. WARNING: Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity.
Page 171 Driving Hints Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle, loss of vehicle control, vehicle rollover or personal injury. The van should be operated by an experienced driver. An organization that owns a 15–passenger van should select one or two experienced drivers to drive the van on a regular basis.
Page 172: Economical Driving
Driving Hints • If the vehicle goes from one type of surface to another (i.e., from concrete to gravel) there will be a change in the way the vehicle responds to a maneuver (steering, acceleration or braking). Again, avoid these abrupt inputs. •...
Page 173 Driving Hints • Keep the tires properly inflated and use only the recommended size. • Use the recommended engine oil. • Perform all regularly scheduled maintenance. There are also some things you may not want to do because they may reduce your fuel economy: •...
Page 174: Floor Mats
Driving Hints If driving through deep or standing water is unavoidable, proceed very slowly. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars). Once through the water, always try the brakes. Wet brakes do not stop the vehicle as effectively as dry brakes.
Page 175 Driving Hints WARNING (Continued) • Never place floor mats or any other covering in the vehicle footwell that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle. • Never place floor mats or any other covering on top of already installed floor mats.
Page 176: Roadside Emergencies
ROADSIDE ASSISTANCE Vehicles Sold in the U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: •...
Page 177 U.S. Ford vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest dealership within 35 miles (56 kilometers). To obtain reimbursement information, U.S.
Page 178: Hazard Flasher Control
WARNING: Failure to inspect and, if necessary, repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision. In the event of a moderate to severe collision, this vehicle is equipped with a fuel pump shut-off feature that stops the flow of fuel to the engine.
Page 179: Jump-Starting The Vehicle
Roadside Emergencies JUMP-STARTING THE VEHICLE WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your automatic transmission vehicle.
Page 180 Roadside Emergencies Connecting the Jumper Cables WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points.
Page 181 Roadside Emergencies Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface.
Page 182: Customer Assistance
A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford.
Page 183 • The name of the authorized dealer and city where located • The vehicle’s current odometer reading. In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.
Page 184 In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126...
Page 185 BBB Auto Line dispute, and decision, are admissible in the court action. Should you choose to accept the BBB AUTO LINE decision, Ford is then bound by the decision, and must comply with the decision within 30 days of receipt of your acceptance letter.
Page 186 ONLY) This pertains to vehicles delivered to authorized Canadian dealers. In those cases, where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation or arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 187 Central America, the Caribbean, and Israel, contact the nearest authorized dealer. If the authorized dealer cannot help you, contact: FORD MOTOR COMPANY FORD EXPORT OPERATIONS & GLOBAL INITIATIVES Customer Relationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U.S.A.
Page 188 If you buy your vehicle in North America and then relocate to any of the above locations, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations & Global Growth Initiatives by emailing expcac@ford.com. If you are in another foreign country, contact the nearest authorized dealer.
Page 189: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153);...
Page 190: Fuses
Fuses CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in your vehicle are not working, a fuse may have blown.
Page 191: Fuse Specification Chart
Fuses FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. Note: If your vehicle is equipped with a dual battery, disconnecting the primary under-hood battery does not remove power from all circuits.
Page 192 Fuses The high-current fuses are coded as follows: Fuse or relay Fuse amp Protected components location rating HC micro relay Powertrain control module HC micro relay Starter solenoid HC micro relay Wiper HC micro relay Trailer tow battery charge HC micro relay Fuel pump HC micro relay Trailer tow park lamp...
Page 193 Fuses Fuse or relay Fuse amp Protected components location rating — Not used 20A* Back-up lamp 10A* Air conditioning clutch 10A* Brake on/off switch 10A* Cluster battery (stripped chassis) 50A** Blower motor 40A** Anti-lock brake system pump 20A** Stripped chassis horn 40A** Powertrain control module relay 20A**...
Page 194 Fuses Fuse or relay Fuse amp Protected components location rating 10A* Anti-lock brake system run/start feed 10A* Fuel pump relay coil — Not used — Not used 20A* Trailer tow park lamp 15A* Trailer tow backup lamp — Not used —...
Page 195 Fuses Fuse or relay Fuse amp Protected components location rating 15A* Vehicle power 4, Fuel pump relay coil 10A* Vehicle power 5, Transmission 10A* Cluster run/start (stripped chassis) — Not used — Not used — Fuel pump (diode) — Not used HC micro relay Auxiliary switch #1 * Mini fuses ** A1S fuses...
Page 196 Fuses The fuses are coded as follows: Fuse or relay Fuse amp Protected components location rating Inverter B+ Not used (spare) Not used (spare) Not used (spare) Passenger compartment fuse panel, Brake-shift interlock Turn signal, Hazard, Stop lamps Left low beam Right low beam Courtesy lamps Switch illumination...
Page 197 Fuses Fuse or relay Fuse amp Protected components location rating 7.5A Not used (spare) Mirrors SYNC, Global positioning system module Not used (spare) Not used (spare) Door locks Not used (spare) Not used (spare) Diagnostic connector (except stripped chassis) Not used (spare) Park lamps, License plate lamps High beams Horn (except stripped chassis)
Page 198 Fuses Fuse or relay Fuse amp Protected components location rating Radio, Navigation Amplifier Radio, Switch illumination, Reverse camera mirror, Automatic dimming rear view mirror, Inverter Auxiliary switch Stripped chassis instrument panel connector #1 Trailer tow battery charge relay Wipers, Stripped chassis Engine connector 3 7.5A Passenger airbag deactivation...
Page 199: Maintenance
GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers who are there to help you with their professional servicing expertise. We believe that their specially trained technicians are best qualified to service your vehicle properly and expertly.
Page 200: Opening And Closing The Hood
Maintenance OPENING AND CLOSING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and push the auxiliary latch, located in the center top of the grille, to the left in order to release the hood.
Page 201: Under Hood Overview
Maintenance UNDER HOOD OVERVIEW A. Battery B. Windshield washer fluid reservoir C. Engine oil filler cap D. Automatic transmission fluid dipstick E. Air filter assembly F. Engine oil dipstick G. Power steering fluid reservoir H. Brake fluid reservoir I. Engine coolant reservoir J.
Page 202: Engine Oil Dipstick
Maintenance ENGINE OIL DIPSTICK A. MIN B. MAX ENGINE OIL CHECK Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait 15 minutes for the oil to drain into the oil pan.
Page 203: Engine Coolant Check
1. Check the engine oil level. 2. If the engine oil level is not within the normal range, add engine oil that meets Ford specifications. See Capacities and Specifications for more information. Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening.
Page 204 Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300ROB75240 available from your dealer. Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable; do not use engine coolant/antifreeze or windshield washer fluid outside of its specified function and vehicle location.
Page 205 Severe Climates If you drive in extremely cold climates: • It may be necessary to have a Ford authorized dealer increase the coolant concentration above 50%. • A coolant concentration of 60% will provide improved freeze point protection.
Page 206 Maintenance • A coolant concentration of 40% will provide improved overheat protection. Engine coolant concentrations below 40% will decrease the corrosion/freeze protection characteristics of the engine coolant and may cause engine damage. Vehicles driven year-round in non-extreme climates should use prediluted engine coolant for optimum cooling system and engine protection.
Page 207 Maintenance When Fail-Safe Mode is Activated WARNING: Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs. When in fail-safe mode, the vehicle will have limited power, will not be able to maintain high-speed operation, and may completely shut down without warning, potentially losing engine power, power steering assist,...
Page 208: Automatic Transmission Fluid Check
Maintenance TRANSMISSION FLUID CHECK Checking Automatic Transmission Fluid (If Equipped) Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does not consume fluid. However, the fluid level should be checked if the transmission is not working properly, i.e., if the transmission slips or shifts slowly or if you notice some sign of fluid leakage.
Page 209 Maintenance Low Fluid Level Do not drive the vehicle if there is no indication of fluid on the dipstick and the ambient temperature is above 50°F (10°C). 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 210 Maintenance Correct Fluid Level The transmission fluid should be checked at normal operating temperature 150°F-170°F (66°C-77°C) on a level surface. The normal operating temperature can be reached after approximately 20 miles (30 km) of driving. You can check the fluid without driving if the ambient temperature is above 50°F (10°C).
Page 211 Maintenance The transmission fluid should be in this range if at ambient temperature (50°F-95°F [10°C-35°C]). 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 212 Maintenance High Fluid Level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 213 Maintenance Adjusting Automatic Transmission Fluid Levels Note: Use of a non-approved automatic transmission fluid may cause internal transmission component damage. Note: An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Note: Do not use supplemental transmission fluid additives, treatments or cleaning agents.
Page 214 Maintenance If an overfill occurs, excess fluid should be removed by an authorized dealer. 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 215 Maintenance Automatic Transmission Fluid Filter The TorqShift® automatic transmission is equipped with a serviceable transmission fluid filter located inside the transmission bottom pan. Refer to your Scheduled Maintenance Information for service intervals for automatic transmission fluid and transmission filter. For transmission filter maintenance, see your authorized dealer.
Page 216: Brake Fluid Check
Maintenance POWER STEERING FLUID CHECK WARNING: For E-350 and E-450 vehicles with the Hydro-Boost Brake System, do not press the brake pedal after the engine has been turned off. Pressing the brake pedal after the engine has been turned off will give a false power steering fluid level reading. Note: Do not operate the vehicle with a low power steering pump fluid level (if the fluid level is below the MIN line on the reservoir).
Page 217: Washer Fluid Check
Maintenance Add fluid to fill the reservoir if the level is low. Only use a washer fluid that meets Ford specifications. See the technical specifications chart in the Capacities and Specifications chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 218 Maintenance Note: If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. Note: Electrical or electronic accessories or components added to the vehicle by the dealer or the owner may adversely affect battery performance and durability.
Page 219 Maintenance 2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6.
Page 220: Checking The Wiper Blades
Maintenance CHECKING THE WIPER BLADES Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth. CHANGING THE WIPER BLADES Replace wiper blades at least once per year for optimum performance.
Page 221 Maintenance When changing the air filter element, use only the air filter element listed. See Motorcraft® Part Numbers in the Capacities and Specifications chapter. See Scheduled Maintenance Information for the appropriate intervals for changing the air filter element. Note: Failure to use the correct air filter element may result in severe engine damage.
Page 222: Adjusting The Headlamps
Maintenance ADJUSTING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident, the alignment of your headlamps should be checked by your authorized dealer. Vertical and Horizontal Aim Adjustment (Sealed Beam Headlamps) The headlamps on your vehicle are intended to be aimed using mechanical aimers.
Page 223 Maintenance 3. Turn on the low beam headlamps and open the hood. 4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (D). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust 5.
Page 224 Maintenance • (A) 8 feet (2.4 meters) • (B) Center height of lamp to ground • (C) 25 feet (7.6 meters) • (D) Horizontal reference line 2. Measure the height from the center of your headlamp (indicated by a 3.0 millimeter circle on the lens) to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of...
Page 225: Changing A Bulb
Maintenance CHANGING A BULB Lamp Assembly Condensation Exterior lamps are vented to accommodate normal changes in pressure. Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold.
Page 226 Maintenance 1. Make sure the headlamp switch is in the off position, then open the hood. 2. Remove the three screws from the headlamp assembly and pull the assembly straight out. 3. Disconnect the electrical connector by squeezing the release tab and pushing the connector forward, then pulling it rearward.
Page 227 Maintenance Replacing Front Parking Lamp and Turn Signal Bulbs 1. Make sure the headlamp control is in the off position. 2. Remove the headlamp assembly. Refer to Replacing headlamp bulbs in this section. Aerodynamic Sealed Beam 3. Rotate the bulb socket counterclockwise and remove. 4.
Page 228 Maintenance Replacing Side Marker Bulbs 1. Make sure the headlamp control is in the off position. 2. Remove the headlamp assembly. Refer to Replacing headlamp bulbs in this section. Aerodynamic Sealed Beam 3. Rotate the bulb socket counterclockwise and remove. 4.
Page 229 Maintenance Replacing High-Mount Brake Lamp Bulbs On vehicles without a rear headliner, the interior cargo lamp (if equipped) must be removed from under the high-mount brake lamp assembly located inside the vehicle. Then, do the following: 1. Remove the two screws from the high-mount brake lamp assembly and lift the lamp from the vehicle.
Page 230 Maintenance Replacing Stop, Turn, Tail, Side Marker, and Backup Lamp Bulbs The stop, turn, tail, side marker, and backup lamp bulbs are located in the tail lamp assembly. Follow the same steps to replace any of the bulbs: 1. Turn the headlamp switch to the off position, then remove the four screws and the lamp assembly from the vehicle.
Page 231 Maintenance BULB SPECIFICATION CHART Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
Page 232: Vehicle Care
Vehicle Care GENERAL INFORMATION Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following products or products of equivalent quality: Motorcraft® Bug and Tar Remover (ZC-42)
Page 233 Vehicle Care • Dry the vehicle with a chamois or soft terry cloth towel in order to eliminate water spotting. • Immediately remove items such as gasoline, diesel fuel, bird droppings and insect deposits because they can cause damage to the vehicle’s paintwork and trim over time.
Page 234: Waxing
Vehicle Care WAXING Regular waxing is necessary to protect your car’s paint from the elements. We recommend that you wash and wax the painted surface once or twice a year. When washing and waxing, park your vehicle in a shaded area out of direct sunlight.
Page 235: Cleaning The Windows And Wiper Blades
Vehicle Care • Spray Motorcraft® Engine Shampoo and Degreaser on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft® Engine Shampoo. • Never wash or rinse the engine while it is hot or running; water in the running engine may cause internal damage.
Page 236: Cleaning The Interior
Vehicle Care CLEANING THE INTERIOR WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side airbag system and affect performance of the side airbag in a collision.
Page 237: Cleaning Leather Seats
Vehicle Care • Be certain to wash or wipe your hands clean if you have been in contact with certain products, such as insect repellent and suntan lotion, in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens.
Page 238: Cleaning The Alloy Wheels
Vehicle Care CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. Aluminum wheels and wheel covers are coated with a clearcoat paint finish. In order to maintain their condition: • Clean weekly with Motorcraft Wheel and Tire Cleaner. Use a sponge to remove heavy deposits of dirt and brake dust accumulation.
Page 239 Vehicle Care General • Store all vehicles in a dry, ventilated place. • Protect from sunlight, if possible. • If vehicles are stored outside, they require regular maintenance to protect against rust and damage. Body • Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from exterior surfaces, rear-wheel housing and underside of front fenders.
Page 240 Vehicle Care Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for more than 30 days without recharging the battery, it may be advisable to disconnect the battery cables to ensure battery charge is maintained for quick starting. Note: If battery cables are disconnected, it will be necessary to reset memory features.
Page 241: Wheels And Tires
Wheels and Tires GENERAL INFORMATION Notice to Utility Vehicle, Van and Truck Owners WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. To reduce the risk of serious injury or death from a rollover or other crash you must: •...
Page 242 Wheels and Tires How Your Vehicle Differs from Other Vehicles Sport-utility vehicles, vans and trucks can differ from some other vehicles in a few noticeable ways. Your vehicle may be: • Higher – to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody...
Page 243: Tire Care
10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it.
Page 244 Wheels and Tires Traction AA A B C WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
Page 245 Wheels and Tires • Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a maximum load at 35 psi [37 psi (2.5 bar) for Metric tires]. Increasing the inflation pressure beyond this pressure will not increase the tire’s load-carrying capability.
Page 246 Wheels and Tires INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT Tire Identification Number for safety standard certification and in case of a recall.
Page 247 Wheels and Tires Note: You may not find this information on all tires because it is not required by federal law. G. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure.
Page 248 Wheels and Tires I. M+S or M/S: Mud and Snow, or AT: All Terrain, or AS: All Season. J. Tire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber-coated fabric in the tire tread and sidewall.
Page 249 Wheels and Tires Additional Information Contained on the Tire Sidewall for LT Type Tires LT type tires have some additional information beyond those of P type tires. These differences are described below. Note: Tire Quality Grades do not apply to this type of tire. A.
Page 250 Wheels and Tires Information on T Type Tires T type tires have some additional information beyond those of P type tires. These differences are described below. T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
Page 251 You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge.
Page 252 Wheels and Tires Maximum Inflation Pressure is the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’s recommended cold inflation pressure, which can be found on the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), or Tire Label which is located...
Page 253 Wheels and Tires Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type mini-spare tires, see the Dissimilar Spare Tire and Wheel Assembly Information section. Store and maintain at 60 psi (4.15 bar). For full-size and dissimilar spare tires, see Dissimilar Spare Tire and Wheel Assembly Information under Changing a Road Wheel in this chapter.
Page 254 Wheels and Tires All tires with Steel Carcass Plies (if equipped): This type of tire utilizes steel cords in the sidewalls. As such, they cannot be treated like normal light truck tires. Tire service, including adjusting tire pressure, must be performed by personnel trained, supervised and equipped according to Federal Occupational Safety and Health Administration regulations.
Page 255 Wheels and Tires WARNING: Stay out of the trajectory (1) as indicated in the illustration. Inspecting Your Tires and Wheel Valve Stems Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves.
Page 256 Wheels and Tires Improper or inadequate vehicle maintenance can cause tires to wear abnormally. Inspect all your tires, including the spare, frequently, and replace them if one or more of the following conditions exist: Tire Wear When the tread is worn down to 1/16th of an inch (2 millimeters), tires must be replaced to help prevent your vehicle from skidding...
Page 257 (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size may be found on either the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge that meets the door-latch post, next to the driver’s seating position), or the Tire Label...
Page 258 The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system.
Page 259 Wheels and Tires WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits. •...
Page 260 Wheels and Tires Tire Rotation WARNING: If the tire label shows different tire pressures for the front and rear tires and the vehicle is equipped with a tire pressure monitoring system, then the settings for the system sensors need to be updated. Always perform the system reset procedure after tire rotation.
Page 261: Using Snow Chains
USING SNOW CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Page 262: Tire Pressure Monitoring System (Tpms)
Wheels and Tires Follow these guidelines when using snow tires and chains: • If possible, avoid fully loading your vehicle. • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. •...
Page 263 Wheels and Tires Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated.
Page 264 Wheels and Tires Understanding Your Tire Pressure Monitoring System The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low. Once the light is illuminated, your tires are under-inflated and need to be inflated to the manufacturer’s recommended tire pressure.
Page 265 Wheels and Tires When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn you when your tires need air. It can also warn you in the event the system is no longer capable of functioning as intended.
Page 266 Wheels and Tires Low tire Possible Customer action required pressure cause warning light Flashing warning Spare tire in Repair the damaged road wheel light and tire assembly and reinstall it on the vehicle to restore system function. For a description on how the system functions, see When your temporary spare tire is installed in this section.
Page 267 • To reduce the chances of interference from another vehicle, the system reset procedure should be performed at least three feet (one meter) away from another Ford Motor Company vehicle undergoing the system reset procedure at the same time. • Do not wait more than two minutes between resetting each tire sensor or the system will time-out and the entire procedure will have to be repeated on all four wheels.
Page 268 Wheels and Tires Performing the System Reset Procedure It is recommended that you read the entire procedure before attempting. 1. Drive the vehicle above 20 mph (32 km/h) for at least two minutes and then park in a safe location where you can easily get to all four tires and have access to an air pump.
Page 269: Changing A Road Wheel
Wheels and Tires Training is complete after the horn sounds for the last tire trained (driver’s side rear tire), the system indicator stops flashing, and the message center (if equipped) displays: TRAINING COMPLETE. 10. Turn the ignition off. If two short horn beeps are heard, the reset procedure was unsuccessful and must be repeated.
Page 270 Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.
Page 271 Wheels and Tires 3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire and wheel assembly, do not: • exceed 70 mph (113 km/h). • use more than one dissimilar spare tire and wheel at a time. •...
Page 272 Wheels and Tires WARNING: Never get underneath a vehicle that is supported only by a jack. If the vehicle slips off the jack, you or someone else could be seriously injured. WARNING: Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Page 273 Wheels and Tires To remove the spare tire: 1. Open the rear doors and remove the thumb screw and anti-theft bracket. If finger pressure will not remove the thumb screw, use the lug wrench to loosen the screw. 2. Remove the access plug under the left door.
Page 274 Wheels and Tires • The jack is located in the rear right-hand side of the cargo area. 8. Remove any wheel trim. Insert the tapered end of the lug nut wrench behind wheel covers or hubcaps and twist off. 9. Loosen the wheel nut by pulling up on the handle of the lug nut wrench about one-half turn (counterclockwise).
Page 275 Wheels and Tires Rear axle jacking points - All models except E-350 dual rear wheel and E-450 Rear axle jacking points - E-350 dual rear wheel and E-450 Front axle jacking points: Note: Do not place the jack under or on the steering linkage. Place the jack under the pin on the front surface of the front axle.
Page 276 Wheels and Tires 8. Remove the jack and fully tighten the lug nuts in the following pattern. See Wheel Lug Nut Torque Specifications in this chapter for the proper lug nut torque specification. 9. Install any wheel covers, ornaments or hub caps. Make sure they are snapped in place.
Page 277: Technical Specifications
9/16 x 18 conical lug 9/16 x 18 two-piece lug nut * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 278 Wheels and Tires On all two-piece flat wheel nuts, apply one drop of motor oil between the flat washer and the nut. Do not apply motor oil to the wheel nut threads or the wheel stud threads. Note: Inspect the wheel pilot hole and mounting surface prior to installation.
Page 279: Capacities And Specifications
Capacities and Specifications ENGINE SPECIFICATIONS Engine 4.6L V8 engine 5.4L V8 engine 6.8L V10 engine Cubic inches Minimum Minimum Minimum Required fuel 87 octane or 87 octane or 87 octane Firing order 1-3-7-2-6-5-4-8 1-3-7-2-6-5-4-8 1-6-5-10-2-7-3-8-4-9 Ignition Coil on plug Coil on plug Coil on plug system Spark plug...
Page 280 Capacities and Specifications • 4.6L V8, 5.4L V8 and 6.8L V10 engines with A/C 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 281 Capacities and Specifications 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 282 Capacities and Specifications 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 283 Capacities and Specifications 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 284 Capacities and Specifications 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 285 Capacities and Specifications 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 286: Part Numbers
Capacities and Specifications MOTORCRAFT® PART NUMBERS 6.8L V10 Component 4.6L V8 engine 5.4L V8 engine engine Air filter element FA-1632 FA-1632 FA-1632 Battery- BXT-65-650 / BXT-65-650 / BXT-65-650 / standard / (BXT-65-750) (BXT-65-750) (BXT-65-750) (auxiliary) Oil filter FL-820-S FL-820-S FL-820-S Spark plugs Torqshift automatic...
Page 287: Vehicle Certification Label
Capacities and Specifications The Vehicle Identification Number (VIN) contains the following information: A. World manufacturer identifier B. Brake system / Gross Vehicle Weight Rating (GVWR) / Restraint Devices and their location C. Make, vehicle line, series, body type D. Engine type E.
Page 288: Transmission Code Designation
Capacities and Specifications TRANSMISSION CODE DESIGNATION You can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents. Description Code Five-speed automatic (5R110W) Four-speed automatic (4R75E) 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 289: Accessories
Accessories.Ford.com (U.S. only). Ford Custom Accessories are available for your vehicle through your authorized Ford or Ford of Canada dealer. Ford Motor Company will repair or replace any properly authorized dealer-installed Ford Custom Accessories found to be defective in factory-supplied materials or workmanship during the warranty period, as well as any component damaged by the defective accessories.
Page 290 Ford Motor Company engineering requirements. Contact your authorized Ford dealer for details regarding the manufacturer’s limited warranty and/or a copy of the Ford Licensed Accessories product limited warranty offered by the accessory manufacturer.
Page 291: Upfitter Controls
AUX 2 CAC06 Green with Brown Trace AUX 3 CAC07 Violet with Green Trace AUX 4 CAC08 Brown More detailed information about upfitter switches can be found at https://www.fleet.ford.com/truckbbas/. 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 292: Ford Extended Service Plan
3. BaseCARE – Covers 84 components 4. PowertrainCARE – Covers 29 critical components Ford ESP is honored by all Ford and Lincoln Dealers in the United States and Canada. It is the only Extended Service Plan authorized and backed by Ford Motor Company. That means you get: •...
Page 293 • Destination assistance for taxi, shuttle, rental car coverage and emergency transportation Transferable Coverage If you sell your vehicle before your Ford Extended Service Plan coverage expires, you can transfer any remaining coverage to the new owner. Whenever you sell your vehicle, prospective buyers may have a higher...
Page 294 To learn more, call our Ford ESP specialists at 800-367-3377. Don’t forget to ask about our interest free payment program, allowing you all the security and benefits Ford ESP has to offer while paying over time. You are pre-approved with no credit checks, no hassles!
Page 295: Audio System
Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Note: Do not insert CDs with homemade paper (adhesive) labels into the CD player as the label may peel and cause the CD to become jammed.
Page 296 Audio System MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracks and folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 track mode (system default) and MP3 folder mode. •...
Page 297: Am/Fm Stereo
Audio System AM/FM AUDIO WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 298: Am/Fm/Cd With Sync
Audio System E. Memory presets: Store your favorite radio stations. To store a radio station, tune to the station, then press and hold a preset button until sound returns. F. AM/FM: Press this button to select a frequency band and access media through the auxiliary input jack.
Page 299 Audio System D. Phone: Press this button to access the phone features of the SYNC® system. See the SYNC® chapter for more information. E. MENU: Press this button to access different audio system features. • If your vehicle is equipped with satellite radio, you can access different menus by pressing OK.
Page 300: Satellite Radio Information
Audio System M. REW: Press this button to manually rewind in a CD track or MP3 file. N. Memory presets: Store your favorite radio stations. To store a radio station, tune to the station, then press and hold a preset button until sound returns.
Page 301 Note: Sirius reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes.
Page 302 Audio System Satellite Radio Electronic Serial Number (ESN) You need your ESN to activate, modify or track your satellite radio account. When in satellite radio mode, you can view this number by pressing SIRIUS and memory preset 1 at the same time. To access your ESN, press the bottom left corner of the touchscreen, then SIRIUS >...
Page 303: Auxiliary Input Jack
Audio System Radio display Condition Possible action Call SIRIUS Your satellite service is Call Sirius at 1–888–539–7474 no longer available. 1–888–539–7474 to resolve subscription issues. None Found. Check All the channels in the Use the channel guide Channel Guide. selected category are to turn off the Lock or either skipped or Skip function on that...
Page 304 Audio System The auxiliary input jack allows you to connect and play music from your portable music player through your vehicle speakers. You can use any portable music player designed for use with headphones. Your audio extension cable must have male ⁄...
Page 305: Usb Port
Audio System USB PORT (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 306: Sync
SYNC® SYNC is an in-vehicle communications system that works with your Bluetooth-enabled cellular phone and portable media player. This allows you to: • Make and receive calls. • Access and play music from your portable music player. • Use 911 Assist, Vehicle Health Report and SYNC Services (Traffic, Directions &...
Page 307 SYNC® GENERAL INFORMATION Make sure you review your device’s manual before using it with SYNC. Support The SYNC support team is available to help you with any questions you cannot answer on your own. Monday-Saturday, 8:30am-9:00pm EST. Sunday, 10:30am-7:30pm EST. In the United States, call: 1–800–392–3673.
Page 308 Master Reset to erase all stored information. System data cannot be accessed without special equipment and access to the vehicle’s SYNC module. Ford Motor Company and Ford of Canada do not access the system data for any purpose other than as described...
Page 309 SYNC® USING VOICE RECOGNITION This system helps you control many features using voice commands. This allows you to keep your hands on the wheel and focus on what is in front of you. Initiating a Voice Session Push the voice icon; a tone sounds and Listening appears in the display.
Page 310 SYNC® Adjusting the Interaction Level Push the voice icon; when prompted, say “Voice settings”, then any of the following: When you say: The system: “Interaction mode standard” Provides more detailed interaction and guidance. “Interaction mode advanced” Provides less audible interaction and more tone prompts.
Page 311: Pairing Your Phone For The First Time
SYNC® • Speak naturally, without long pauses between words. • At any time you can interrupt the system while it is speaking by pressing the voice icon. USING SYNC WITH YOUR PHONE Hands-free calling is one of the main features of SYNC. While the system supports a variety of features, many are dependent on your cellular phone’s functionality.
Page 312 SYNC® Depending on your phone’s capability and your market, the system may prompt you with questions such as setting the current phone as the primary phone (the phone SYNC automatically tries to connect with first upon vehicle start-up), downloading your phone book, etc. Pairing Subsequent Phones Note: To scroll through the menus, press the up and down arrows on your audio system.
Page 313 SYNC® “PHONE” “Call <name> at home” “Call <name> at work” OR “Call <name> in office” “Dial” “Phone book <name>” “Phone book <name> at work” OR “Phone book <name> at office” “Call history incoming” “Connections” “Go to privacy” “Hold” These commands do not require you to say “Phone” first. These commands are not available until phone information is completely downloaded using Bluetooth.
Page 314 SYNC® Phone book commands: When you ask SYNC® to access a phone book name, number, etc., the requested information appears in the display to view. Press the phone button and say “Call” to call the contact. “DIAL” “411” (four-one-one), “911” (nine-one-one) “700 (seven hundred)”...
Page 315 SYNC® Phone Options during an Active Call During an active call, you have additional menu features which become available such as putting a call on hold, joining calls, etc. Use the arrow buttons to scroll through the menu options. To access: 1.
Page 316 SYNC® When you select: You can: Enter Tones Enter “tones” such as numbers for passwords. Scroll until the desired number appears in the display, then press OK; a tone sounds as confirmation. Repeat as necessary. Access your phonebook contacts. Phonebook 1.
Page 317 SYNC® Accessing Features through the Phone Menu SYNC’s phone menu allows you to redial a number, access your call history and phone book and send text messages as well as access phone and system settings. You can also access advanced features, such as 911 Assist, Vehicle Health Report and SYNC Services.
Page 318 SYNC® When you select: You can: Text Message Enables you to send, download and delete text messages. Phone Settings Allows you to view your phone’s status, set ring tones, select your message notification, change phone book entries and automatically download your cellular phone among other features.
Page 319 SYNC® Receiving a Text Message Note: This is a phone-dependent feature. Your phone must support downloading text messages using Bluetooth to receive incoming text messages. Note: Forwarding a text message is a speed-dependent feature and can only be done when the vehicle is traveling at 3 mph (5 km/h) or less. Note: Only one recipient is allowed per text message.
Page 320 6. Press OK when the contact appears and press OK again to confirm when the system asks if you would like to send the message. Each text message is sent with the following signature: “This message was sent from my <Ford or Lincoln>”. Pre-defined text message options Can’t talk right now...
Page 321 SYNC® Accessing Your Phone Settings These are phone-dependent features. Your phone settings allow you to access and adjust features such as your ring tone, text message notification, modify your phone book and also set up automatic download. 1. Press the phone button. 2.
Page 322 SYNC® When you select: You can: Modify Phonebook Modify the contents of your phone book (i.e., add, delete, download). Press OK to select and scroll between: Add Contacts: Press OK to add more contacts from your phone book. Push the desired contact(s) on your phone.
Page 323 SYNC® System Settings System Settings provide access to your Bluetooth Devices and Advanced menu features. Use the arrow buttons to scroll through the menu options. The Bluetooth Devices menu allows you to add, connect, delete and set a phone as primary as well as turn your Bluetooth feature on and off. The Advanced menu allows you to access and set prompts, languages, defaults, perform a master reset, install an application and view system information.
Page 324 SYNC® If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off. Press OK and scroll to toggle between On and Off. When the desired selection is chosen, press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates all Bluetooth features.
Page 325 SYNC® If you select: You can: Languages Choose between English, Espanol and Francais. Once selected, all of SYNC’s radio displays and prompts are in the selected language. 1. Press OK to select and then scroll through the languages. 2. Press OK when the desired selection appears in the display.
Page 326: Assist
SYNC® SYNC APPLICATIONS AND SERVICES (IF EQUIPPED) Note: In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone’s compatibility, visit www.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • SYNC Services (if equipped, United States only): Provides access to traffic, directions and information such as travel, horoscopes, stock prices and more.
Page 327 SYNC® Note: Every phone operates differently. While SYNC 911 Assist works with most cellular phones, some may have trouble using this feature. If a crash deploys an airbag (excludes knee airbags and rear inflatable safety belts [if equipped]) or activates the fuel pump shut-off, your SYNC equipped vehicle may be able to contact emergency services by dialing 911 through a paired and connected Bluetooth-enabled phone.
Page 328 SYNC® In the Event of a Crash Not all crashes deploy an airbag or activate the fuel pump shut-off (which would activate 911 Assist); however, if 911 Assist is triggered, SYNC tries to contact emergency services. If a connected phone is damaged or loses connection to SYNC, SYNC searches for, and tries to connect to, any available previously paired phone and tries to make the call to 911.
Page 329: Vehicle Health Report
SYNC® Vehicle Health Report WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Report supplements, but cannot replace normal maintenance and vehicle inspection. Vehicle Health Report only monitors certain systems that are electronically monitored by the vehicle and will not monitor or report the status of any other system, (i.e., brake lining wear).
Page 330 Certain versions or updates to Vehicle Health Report may also collect additional vehicle information. Ford may use the vehicle information it collects for any purpose. If you do not want to disclose your cellular phone number or vehicle information, do not run the feature or set up your Vehicle Health Report profile at www.SYNCMyRide.com.
Page 331 For more information, see SYNC Services Terms and Conditions at www.SYNCMyRide.com. If you do not want Ford or its service providers to collect the vehicle travel information or other information identified in the Terms and Conditions, do not activate or use the service.
Page 332 SYNC® Connecting to SYNC Services Using Voice Commands 1. Press the voice button. 2. When prompted, say “Services”. This initiates an outgoing call to SYNC Services using your paired and connected Bluetooth-enabled cellular phone. 3. Once you are connected to the service, follow the voice prompts to request the desired service, such as “Traffic”...
Page 333 SYNC® Disconnecting from SYNC Services 1. Press and hold the phone button on the steering wheel. 2. Say “Good-bye” from the SYNC Services main menu. SYNC Services quick tips Personalizing You can personalize your Services feature to provide quicker access to your most used or favorite information.
Page 334 SYNC® Note: The AppLink feature is not available if your vehicle is equipped with the MyFord Touch or MyLincoln Touch system. Depending on your display type, you can access AppLink from the media menu, the phone menu, or by using voice commands. Once an app is running through AppLink, you can control main features of the app through voice commands and steering wheel controls.
Page 335 SYNC® USING SYNC WITH YOUR MEDIA PLAYER You can access and play music from your digital music player over the vehicle’s speaker system using the system’s media menu or voice commands. You can also sort and play your music by specific categories, such as artists, albums, etc.
Page 336 SYNC® What’s Playing? At any time when a track is playing, you can press the voice icon and ask the system, “What’s playing?”. The system reads the metadata tags (if populated) of the playing track to you. Media Voice Commands Press the voice icon and, when prompted, say “USB”...
Page 337 SYNC® “USB” “Search song <name>” “Search track <name>” “Shuffle off” “Shuffle on” “Similar music” “What’s playing?” “<name>” is a dynamic listing, meaning that it could be the name of any desired group, artist, etc. Voice commands which are only available in folder mode. Voice commands which are not available until indexing is complete.
Page 338 SYNC® Voice command guide “Refine” This allows you to make your previous command more specific. For example, if you asked to search and play all music by a certain artist, you could then say “refine album” and choose a specific album from the list to view.
Page 339 SYNC® When you select: You can: SYNC USB: Press OK to access music Select Source plugged into your USB port. You can also plug in devices to charge them (if supported by your device). Once connected, the system indexes any readable media files. (The time required to complete this depends on the size of the media content being indexed.) If Autoplay is on, you can access media files...
Page 340 SYNC® When you select: You can: Media Settings Choose to shuffle or repeat your music and select your Autoplay settings. Once these selections are turned on, they remain on until turned off. Press SEEK to play the previous or next track. Note: Some digital media players require both USB and line in ports to stream data and music separately.
Page 341 SYNC® Accessing Your Play Menu This menu allows you to select and play your media by artist, album, genre, playlist, track, similar music or even to explore what is on your USB device. 1. Make sure that your device is plugged into the USB port and is turned on.
Page 342 SYNC® When you select: You can: Albums Sort all indexed media by albums. If there are less than 255 indexed albums, they are listed alphabetically in flat file mode. If there are more, they are organized into alphabetical categories. 1. Press OK to enter the album menu and select from playing all albums or from any individual indexed album.
Page 343 SYNC® When you select: You can: Explore USB Explore all supported digital media on your media device connected to the USB port. You can only view media content which is compatible with SYNC; other files saved are not visible. Press OK to select. Then scroll to explore indexed media on your flash drive.
Page 344 SYNC® Bluetooth Devices Menu Options This menu allows you to add, connect and delete devices as well as turn Bluetooth on and off. 1. Press AUX and then MENU to enter the Media Menu. 2. Scroll until System Settings appears and select OK. 3.
Page 345 SYNC® Advanced Menu Options This menu allows you to access settings such as prompts, language, performing a master reset as well as returning to factory defaults. 1. Press AUX and then MENU to access the Media Menu. 2. Scroll until System Settings appears and select OK. 3.
Page 346 SYNC® When you select: You can: Master Reset Completely erase all information stored on SYNC (all phonebook, call history, text messages and all paired devices) and return to the factory default settings. Application Download new software applications (if available) and then load the desired applications through your USB port.
Page 347 SYNC® Phone issues Issue Possible Possible solution(s) cause(s) • This is a • Go to the website to review SYNC is not able to download my phone-dependent your phone’s compatibility. • Try turning off the device, phonebook. feature, OR • Possible phone resetting the device or removing malfunction.
Page 348 SYNC® Phone issues Issue Possible Possible solution(s) cause(s) • This is a • Go to the website to review I am having trouble phone-dependent your phone’s compatibility. • Try turning off the device, connecting my feature, OR • Possible phone phone to SYNC.
Page 349 SYNC® USB and media issues Issue Possible Possible solution(s) cause(s) • Try turning off the device, I am having Possible device trouble malfunction. resetting the device or removing connecting my the device’s battery, then trying device. again. • Make sure you are using the manufacturer’s cable.
Page 350 SYNC® Vehicle Health Report and SYNC Services (Traffic, Directions and Information) issues Issue Possible Possible solution(s) cause(s) • Your account • This is a free feature, but you I received a text that the Vehicle may not be must first register online to use Health Report is activated on the •...
Page 351 SYNC® Voice command issues Issue Possible Possible solution(s) cause(s) • You may be • Review the Phone voice SYNC does not understand what using the wrong commands and the Media voice I am saying. voice commands, commands at the beginning of their respective sections.
Page 352 SYNC® Voice command issues Issue Possible Possible solution(s) cause(s) • You may be • Review the phone voice SYNC does not understand or is using the wrong commands at the beginning of calling the wrong voice commands, the phone section. •...
Page 353 SYNC® AppLink issues Issue Possible Possible solution(s) cause(s) • Your device • Check the website for SYNC does not find any mobile may not support compatible devices and apps that are on the AppLink applications. • Make sure your device is my phone.
Page 354: Navigation System (If Equipped)
Navigation System (If Equipped) NAVIGATION CONTROLS WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 355 Navigation System (If Equipped) Note: Some features, such as SIRIUS satellite radio, may not be available in your location. Check with your authorized dealer. A. Memory presets: • Store your favorite radio stations. To store a radio station, tune to the station, then press and hold a preset button until sound returns.
Page 356 Navigation System (If Equipped) K. SEEK: • In radio and satellite radio mode, press the arrow buttons to find previous or next available stations or channels within the currently selected Category or Genre. • In CD and DVD modes, press the arrow buttons to select the previous or next track or chapter.
Page 357: Status Bars
Navigation System (If Equipped) Display mode voice commands “Display on” “Display off” “Status bar” “Brighter” “Dimmer” “Day” “Night” “Auto” “Help” STATUS BARS The top status bar shows the current mode, exterior temperature, time and display icons if you have enabled Bluetooth or other options. The bottom status bar shows the Home icon and may also show the Artist and Title of the currently...
Page 358: Loading Pictures
Navigation System (If Equipped) Loading Photos Note: The system is not compatible with discs written in Packet Write mode. Your system allows you to upload and view up to 32 photos. Only the photograph(s), which meets the following conditions, display: •...
Page 359: Voice Recognition
Navigation System (If Equipped) Using the Touch-sensitive Controls on Your System To turn a feature on and off, just touch the graphic with your finger. To get the best performance from the touch-sensitive controls: • Make sure your hands are clean and dry. •...
Page 360 Navigation System (If Equipped) How To Use Voice Commands with Your System Press the voice icon; after the tone, speak your command clearly. You can say these commands at any time. “Audio” “Navigation” “CD” “Radio” “Disc” “SYNC” “Display mode” “Tutorial” “DVD”...
Page 361 Navigation System (If Equipped) Confirmation Prompts: The system uses these short questions to confirm your voice request. If turned off, the system simply makes a best guess as to what you requested. The system may still occasionally ask you to confirm settings. SYSTEM MENU FEATURES Your system offers many menu features, such as allowing you to adjust the touchscreen brightness, time and language, feedback and system...
Page 362 Navigation System (If Equipped) If you select: You can: Feedback Settings Touch Screen Button Beep allows you to select when the system sounds an audible tone: All Buttons (whenever any system button is touched), Touch Screen (only when touchscreen selections are made) or Off (no audible tones at all).
Page 363 Navigation System (If Equipped) If you select: You can: System Settings Language allows you to choose between English, Spanish and French. Units allows you to choose between English and Metric measurements. Keyboard Layout allows you to choose between an ABC or QWERTY keyboard. Delete Stored Items allows you to choose to delete all of the entries from Address Book, Previous Destinations, Avoid Areas, Saved...
Page 364: Accessing Media Features
Navigation System (If Equipped) ENTERTAINMENT Your system offers many media options. You can access these options using the touchscreen or voice commands. AM/FM Radio Press the RADIO hard button. To change between AM, FM1 and FM2, touch the AM or FM tab.
Page 365 Navigation System (If Equipped) When you select: You can: Set PTY/All Select a category of music you would like to search for and then choose to either seek or scan for the stations. Note: The system scans the frequency band three times for the chosen program type.
Page 366 Navigation System (If Equipped) If you are listening to the radio, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not listening to the radio, press the voice button and, after the tone, say “Radio”, then any of the commands in the following chart.
Page 367 Navigation System (If Equipped) HD Radio™ Information (If Available) Note: HD Radio broadcasts are not available in all markets. HD Radio technology is the digital evolution of analog AM/FM radio. Your system has a special receiver that allows it to receive digital broadcasts (where available) in addition to the analog broadcasts, it already receives.
Page 368 Navigation System (If Equipped) When you select: You can: Tune Go up and down the frequency in individual increments. If the current station has multiple digital broadcasts, the multicast indicator appears. Press Tune repeatedly to advance through all available broadcasts. If you are on the last broadcast channel, press to advance to the next frequency on the band.
Page 369 Navigation System (If Equipped) When you select: You can: To save a multicast When the channel is active on-screen, press station as a preset and hold a memory preset slot until the sound returns. There is a brief mute while the radio saves the station.
Page 370 Navigation System (If Equipped) In order to provide the best possible experience, use the contact form to report any station issues found while listening to a station broadcasting with HD Radio technology. Independent entities own and operate each station. These stations are responsible for ensuring all audio streams and data fields are accurate.
Page 371 HD Radio Technology manufactured under license from iBiquity Digital Corp. U.S. and foreign patents. HD Radio and the HD and HD Radio logos are proprietary trademarks of iBiquity Digital Corp. Ford Motor Company and iBiquity Digital Corp. are not responsible for the content sent using HD Radio technology.
Page 372 Navigation System (If Equipped) SIRIUS® Satellite Radio (If Activated) Press the RADIO hard button, then select SAT on the touchscreen. When you select: You can: SAT123 Press this button to access three different satellite radio modes (SAT1, SAT2 or SAT3). Scan Press this button to hear a brief sampling of all satellite radio channels within the current...
Page 373 Titles that you would like the system to alert you to when they are playing on other channels. Note: SIRIUS® does not support the Alert feature on all channels. Ford Motor Company shall not be responsible for Alert feature variation. Show Presets Display presets at the bottom of the screen.
Page 374 Navigation System (If Equipped) SIRIUS® Satellite Radio Voice Commands If you are listening to SIRIUS satellite radio, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not listening to SIRIUS satellite radio, press the voice button and, after the tone, say “Sirius”, then any of the commands in the following chart.
Page 375 Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes.
Page 376 Navigation System (If Equipped) Troubleshooting tips Radio Display Condition Possible Action Acquiring... Radio requires more No action required. than two seconds to This message should produce audio for the disappear shortly. selected channel. Sat Fault/SIRIUS There is an internal If this message does System Failure module or system not clear shortly, or...
Page 377 Navigation System (If Equipped) Press the MEDIA hard button, and then select the CD tab on the touchscreen. If there is no disc in the system, NO DISC appears in the status bar and you cannot access the CD screen. Once a disc is loaded, you can choose from Scan, Compress, Repeat, Shuffle, Track List and Record.
Page 378 Navigation System (If Equipped) Press the MEDIA hard button, and then select the CD tab on the touchscreen. If there is no disc in the system, NO DISC appears in the status bar and you cannot access the CD screen. Once a disc is loaded, you can choose from Scan, Compress, Repeat, Shuffle, Folder Mode and Folder List.
Page 379 Navigation System (If Equipped) When you select: You can: Settings Video Display Settings allows you to adjust the brightness and contrast. You can also choose to return to the default settings by pressing Restore Default. Audio Language allows you to choose which language you would like the DVD audio track to play in.
Page 380 Navigation System (If Equipped) Disc Voice Commands If you are listening to or watching a disc, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not listening to or watching a disc, press the voice button and, after the tone, say “Disc”, then any of the commands in the following chart.
Page 381: Jukebox Features
Navigation System (If Equipped) Video CD Voice Commands If you are watching a video CD, press the voice button on the steering wheel control. When prompted, say any of the commands in the following chart. If you are not watching a video CD, press the voice button and, after the tone, say “Video CD”, then any of the commands in the following chart.
Page 382: Accessing The Music In Your Jukebox
Navigation System (If Equipped) Accessing the Music in Your Jukebox Once you have saved music to your jukebox, you can then choose different ways to play the music. 1. Press the MEDIA hard button on the navigation system. 2. Select the Jukebox tab on the touchscreen. You can then select from the following options: When you select: You can:...
Page 383: Creating A Playlist
Navigation System (If Equipped) Creating a Playlist Press the MEDIA hard button, and then select the Jukebox tab on the touchscreen. 1. Select Options. 2. Select Edit Playlists, then which playlist you would like to create. 3. Select which category you would like to access from your saved music.
Page 384: Where Am I
Navigation System (If Equipped) User Device If your vehicle is equipped with SYNC®, there is a User Device tab. For more information, see the SYNC® chapter. Line In (Auxiliary Input Jack) Your vehicle is equipped with an audio input jack, which allows you to plug a portable audio device into your vehicle’s audio system.
Page 385 Navigation System (If Equipped) Press the I (information) button, then select Sirius Travel Link. Choose from any of the following services: When you select: You can: Traffic On Route Identify traffic incidents on your route, nearby your vehicle’s current location or near any of Traffic Nearby your favorite places (if programmed).
Page 386 Navigation System (If Equipped) SIRIUS Travel Link Voice Commands Press the voice button and, after the tone, say “Travel Link”, then any of the commands in the following chart: “TRAVEL LINK” “5–day weather forecast” “NBA schedule” “Baseball schedule” “NBA scores” “Baseball scores”...
Page 387: Accessing The Help Screen
Navigation System (If Equipped) Calendar Press the I (information) button, then select Calendar. You can then select which month you would like to view by using the arrow buttons or selecting Go to Today. You can view calendars from one previous year and the next 10 years. Note: Not all tab selections may be available in all markets.
Page 388: Navigation Features
Navigation System (If Equipped) SOUND The sound menu allows you to access and adjust settings, such as Bass, Treble, Fade, Balance, Speed Compensated Volume (SCV) and the visualizer. Press the SOUND hard button. When you select: You can: Bass/Treble Increase or decrease levels by pressing + or -. Adjust the sound between the left and right Balance/Fade speakers and front and rear speakers.
Page 389 Navigation System (If Equipped) Route Guidance in Incompletely Mapped Areas There are some rural areas in the map database without fully verified roads. When the system is in route guidance mode, and the navigation system encounters these incompletely mapped areas, the system alerts you by: •...
Page 390 Navigation System (If Equipped) Quick Note: Items on this screen are selectable at any speed. Find Nearest POI Select up to five different points of interest (POI) favorites that you can search for while your vehicle is moving. You can change these categories at any time but the default categories are: •...
Page 391 Navigation System (If Equipped) Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). You can store up to 25 entries, which you can Address Book use as destinations, waypoints and areas to avoid.
Page 392 Navigation System (If Equipped) Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Street Address Touch this button to program a street address as a destination or waypoint. •...
Page 393 Navigation System (If Equipped) Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Touch this button to select a point of interest Point of Interest (POI) on the map as a destination or waypoint. There are three ways to search for a point of interest: 1.
Page 394 Navigation System (If Equipped) Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Freeway Touch this button to select an entrance and Entrance/Exit exit point to a freeway you select. You can sort the entrance and exit point alphabetically or in order of distance from your vehicle’s position.
Page 395 Navigation System (If Equipped) Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Touch this button to select an intersection Intersection point. Enter the name of the first street, then the first letter of the second street.
Page 396 Navigation System (If Equipped) To delete all stored Address Book and Previous Destination entries at once: 1. Press the MENU hard button. 2. Select the System Settings tab. 3. Press the View button for Delete Stored Items. 4. Select Address Book or Previous Destinations. Edit Route Cancel Route Touch this button to cancel the current route.
Page 397 Navigation System (If Equipped) Programming a Destination Using Voice Commands Press the voice button on the steering wheel. If you want to: Say: Enter an address. “Destination street address” Enter an intersection. “Destination intersection” Find a point of interest “Destination nearest <POI category>” or (POI) by its category.
Page 398 Navigation System (If Equipped) Within these main categories, there are subcategories, which contain more listings: Subcategories Restaurant Auto Dealership Parking Public Transit Home & Garden Education Personal Care Services Setting Your Navigation Preferences Select settings for the system to take into account when planning your route.
Page 399 Navigation System (If Equipped) Map Preferences Bird’s Eye View ON provides an elevated map perspective. OFF turns the feature off. Adjust Angle offers six different map angles. Turn List Format Top-to-Bottom starts the turn instructions from the top. Bottom-to-Top starts the turn instructions from the bottom.
Page 400 Navigation System (If Equipped) Traffic Preferences Traffic Icons to Touch this button to display a list of map overlay on Map icons that you can turn off and on. The list of icons includes: • Weather related incidents • Road work •...
Page 401 Navigation System (If Equipped) Navigation Preferences Avg. Speed: When this feature is on, the system displays Residential the average speed on a residential road, initially set to 25 mph (40 km/h). You can change the setting for your driving preferences. This setting helps estimate your arrival time at a destination based on your driving preferences.
Page 402 Navigation System (If Equipped) Navigation Preferences Calibrate Position allows you to adjust the direction of your vehicle by pressing the arrow buttons on the screen. Distance allows you to recalibrate the distance to the destination while your vehicle is moving. Restore Default Touch the Reset button to return the settings Settings...
Page 403 Navigation System (If Equipped) North Up always shows the northern direction to be upward on the screen. Map Icons Vehicle mark shows the current location of your vehicle. It stays in the center of the map display, except when in scroll mode.
Page 404 Navigation System (If Equipped) No GPS symbol indicates that insufficient GPS satellite signals are available for accurate map positioning. This icon may display under normal operation in an area with poor GPS access. Map Scale The map display scale has 17 levels, ranging from 0.02 miles (.03 kilometers) to 1000 miles (1600 kilometers).
Page 405 Navigation System (If Equipped) Quick-touch Buttons When in map mode, touch anywhere on the map display to access the following options: When you select: You can: Set as Dest Select a scrolled location on the map as your destination. You may scroll the map by pressing your index finger on the map display.
Page 406 Annual navigation map updates are available for purchase through your dealership, by calling 1-800-NAVMAPS (in Mexico, call 01–800–557–5539) or going to www.navigation.com/ford. You need to specify the make and model of your vehicle to determine if there is an update available.
Page 407 Navigation System (If Equipped) If you have said the command, “Destination”, you may say any of the above commands or commands in the following Destination chart. “DESTINATION” “<nametag>” “<POI category>” “Home” “Intersection” “Nearest <POI category>” “Nearest POI” “POI” “POI category” “Previous destination”...
Page 408 Navigation System (If Equipped) Symptoms Possible Cause Action A pop-up window The house number Press NO and enter a displays “Address not entered does not exist valid number for the found” or “Address in the map database. specified street, or range does not exist.
Page 409: Appendices
SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by Ford Motor Company and its affiliates (“FORD MOTOR COMPANY”) from an affiliate of Microsoft Corporation (“MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online”...
Page 410 Neither FORD MOTOR COMPANY nor its suppliers shall be liable for any damages arising out of errors in the speech recognition process.
Page 411 • Consent to Use of Data: You agree that MS, Microsoft Corporation, FORD MOTOR COMPANY, third party software and systems suppliers, their affiliates and/or their designated agent may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE or related services.
Page 412 DEVICE. UPGRADES AND RECOVERY MEDIA: If the SOFTWARE is provided by FORD MOTOR COMPANY separate from the DEVICE on media such as a ROM chip, CD ROM disk(s) or via web download or other means, and is labeled “For Upgrade Purposes Only” or For Recovery Purposes...
Page 413 For additional information, see http://www.microsoft.com/exporting/. TRADEMARKS: This EULA does not grant you any rights in connection with any trademarks or service marks of FORD MOTOR COMPANY, MS, Microsoft Corporation, third party software or service providers, their affiliates or suppliers.
Page 414 End user notice Microsoft® Windows® Mobile for Automotive Important Safety Information This system Ford SYNC™ contains software that is licensed to Manufacturer FORD MOTOR COMPANY by an affiliate of Microsoft Corporation pursuant to a license agreement. Any removal, reproduction, reverse engineering or other unauthorized use of the software from this system in violation of the license agreement is strictly prohibited and may subject you to legal action.
Page 415 Appendices Keep User’s Guide in Vehicle When kept in the vehicle, the User’s Guide will be a ready reference for you and other users unfamiliar with the Windows Automotive-based system. Please make certain that before using the system for the first time, all persons have access to the User’s Guide and read its instructions and safety information carefully.
Page 416 Appendices Navigation Features Any navigation features included in the system are intended to provide turn by turn instructions to get you to a desired destination. Please make certain all persons using this system carefully read and follow instructions and safety information fully. Distraction Hazard Any navigation features may require manual (non-verbal) setup.
Page 417: Navigation End User License Agreement
Appendices Map Data DVD End User License Terms The data (“Data”) is provided for your personal, internal use only and not for resale. It is protected by copyright, and is subject to the following terms and conditions which are agreed to by you, on the one hand, and (Licensee).
Page 418 Appendices Disclaimer of warranty:(Licensee) and its licensors (including their licensors and suppliers) disclaim any warranties, express or implied, of quality, performance, merchantability, fitness for a particular purpose or non infringement. Some States, Territories and Countries do not allow certain warranty exclusions, so to that extent the above exclusion may not apply to you.
Page 419 Data provided to you hereunder. FCC Compliance Changes or modifications not approved by Ford could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits with the Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 420 Appendices Gracenote® End User License Agreement (EULA) This device contains software from Gracenote, Inc. of 2000 Powell Street Emeryville, California 94608 (“Gracenote”). The software from Gracenote (the “Gracenote Software”) enables this device to do disc and music file identification and obtain music-related information, including name, artist, track, and title information (“Gracenote Data”) from online servers (“Gracenote Servers”), and to perform other functions.
Page 421 Appendices THE GRACENOTE SOFTWARE, EACH ITEM OF GRACENOTE DATA AND THE GRACENOTE CONTENT ARE LICENSED TO YOU “AS IS.” NEITHER GRACENOTE MAKES ANY REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, REGARDING THE ACCURACY OF ANY GRACENOTE DATA FROM THE GRACENOTE SERVERS OR GRACENOTE CONTENT.
Page 422: Scheduled Maintenance
Parts installed at your dealership carry a nationwide 12-month or 12000-mile (20000 kilometers) parts and labor limited warranty. If you do not use Ford authorized parts they may not meet our specifications and depending on the part, it could affect emissions compliance.
Page 423 Ford Motor Company recommended additives and chemicals are listed in this book and in the Workshop Manual. Additional chemicals or additives not approved by Ford Motor Company are not recommended as part of normal maintenance. Please consult your warranty information.
Page 424 Scheduled Maintenance Owner Checks and Services Certain basic maintenance checks and inspections should be performed every month or at six month intervals. Check every month Engine oil level. Function of all interior and exterior lights. Tires (including spare) for wear and proper pressure. Windshield washer fluid level.
Page 425 In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly. This can help identify potential issues and prevent major problems. Ford Motor Company recommends the following multi-point inspection be performed at every scheduled maintenance interval to help make sure your vehicle keeps running great.
Page 426 Scheduled Maintenance 2013 Econoline (eco) Owners Guide gf, 3rd Printing, May 2013 USA (fus)
Page 427: Normal Scheduled Maintenance And Log
Scheduled Maintenance NORMAL SCHEDULED MAINTENANCE AND LOG Normal scheduled maintenance Every 7500 miles Change engine oil and filter. (12000 km) or six Rotate tires , inspect tire wear and measure months (whichever tread depth. comes first) Inspect wheels and related components for abnormal noise, wear, looseness or drag.
Page 428 Scheduled Maintenance Other maintenance items Every 30000 miles Replace engine air filter. (48000 km) Every 60000 miles Change automatic transmission fluid and filter (96000 km) on 5–speed transmission. Consult dealer for requirements. Replace front wheel bearing grease and grease seal if non-sealed bearings are used. Every 97500 miles Replace spark plugs.
Page 429 Scheduled Maintenance Maintenance Schedule Log EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS...
Page 430 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 431 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 432 Scheduled Maintenance SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you need to have some items maintained more frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additional maintenance. For specific recommendations, see your dealership service advisor or technician.
Page 433 Scheduled Maintenance Extensive idling or low-speed driving for long distances as in heavy commercial use (such as delivery, taxi, patrol car or livery) Every 30000 miles Change automatic transmission fluid on 4–speed (48000 km) transmission. Replace front wheel bearing grease and grease seals if non-sealed bearings are used.
Page 434 Scheduled Maintenance Special Operating Condition Log EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#:...
Page 435 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 436 Normal vehicle axle maintenance: Rear axles and power take-off units with synthetic fluid and light-duty trucks equipped with Ford-design axles are lubricated for life; do not check or change fluid unless a leak is suspected, service is required or the assembly has been submerged in water.
Page 437: Engine Coolant Change Log
Scheduled Maintenance ENGINE COOLANT CHANGE RECORD Initial change Six years or 105000 miles (168000 km) (whichever comes first) After initial change Every three years or 45000 miles (72000 km) Engine Coolant Change Log EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS...
Page 438: Index
Index 911 Assist™ ......325 Antifreeze (see Engine coolant) ....202 Anti-lock brake system (see Brakes) ......132 ABS (see Brakes) .....132 Anti-theft system ......64 Accessing call history/phone arming the system ....64 book during active call .....314 AppLink™ .........332 Accessing the help screen ..386 Audio system Accessing the music in your Single CD ......296–297...
Page 439 ..280 Creating a playlist .....382 parking ........133 Cruise control ......144 shift interlock ......129 Customer Assistance ....175 trailer .......160–161 Ford Extended Service Plan ..........291 Getting roadside assistance ...175 Getting the service you Capacities for refilling fluids ..280 need .........181 CD ........296–297 Ordering additional owner’s...
Page 440 Index Electronic stability control ..137 filter, specifications ....215 fuel pump shut-off ....177 Emergencies, roadside jump-starting ......178 octane rating ....117, 278 running out of fuel ....117 quality ........116 running out of fuel ....117 Emergency Flashers ....177 safety information relating to Emission control system ..120 automotive fuels .....115 End user license agreement ..408 Fuel - flex fuel vehicle...
Page 441 Index Inspection/maintenance (I/M) Locks autolock ........60 testing ........123 doors ..........59 Instrument panel Lubricant specifications ...280 cleaning ........235 cluster ........79 Lug nuts ........276 Jack ..........268 Map icons ........402 positioning .......268 Map mode ........401 storage ........268 Map updates ......405 Joining two calls Media Bluetooth menu options (multiparty/conference call) ..314 (adding, connecting, deleting,...
Page 442 Index Parts Rear window defroster ..92–93 (see Motorcraft® parts) ..285 Receiving a text message ..318 Phone Bluetooth menu options Recommendations for (adding, connecting, deleting, turning on/off) ......322 attaching safety restraints for children ........24 Phone redial ......316 Relays ........189–190 Playing music (by artist, album, genre, playlist, tracks, Remote entry system similar) ........340...
Page 443 Index Scheduled Maintenance Guide SYNC® customer support ..306 Normal Scheduled SYNC® Services ......330 Maintenance and Log .....426 System overview .......353 SD card ........387 Seats child safety seats ......24 front seats ......98, 100 Temperature control SecuriLock passive anti-theft (see Climate control) ...92–93 system ..........64 Text messaging ......317 Selecting your media source...
Page 444 Index Trailer Brake Ventilating your vehicle ...113 Controller-Integrated ....161 Voice commands in media Transmission ......124 mode ..........335 brake-shift interlock (BSI) ..129 fluid, checking and adding Voice commands in phone (automatic) ......207 mode ..........311 fluid, refill capacities ....280 Voice recognition ......358 lubricant specifications ..280 Troubleshooting ......406 Turn signal ........71...

This manual is also suitable for:

Econoline e-250 Econoline e-350 Econoline e-450 Econoline e-150 2013 Econoline e-250 2013 Econoline e-350 2013 ... Show all

Ford Econoline E-150 Owner's Manual

Table of Contents

Table of Contents

Table of Contents

Table of Contents

Introduction

Child Safety

Safety Belts

Supplementary Restraints System

Keys and Remote Control

Locks

Security

Steering Wheel

Wipers and Washers

Lighting

Windows and Mirrors

Instrument Cluster

Information Displays

Climate Control

Seats

Auxiliary Power Points

Starting and Stopping the Engine

Fuel and Refueling

Transmission

Brakes

Traction Control

Stability Control

Parking Aids

Cruise Control

Driving Aids

Load Carrying

Towing

Driving Hints

Roadside Emergencies

Customer Assistance

Fuses

Maintenance

Vehicle Care

Wheels and Tires

Capacities and Specifications

Accessories

Ford Extended Service Plan

Audio System

Sync

Navigation System (if Equipped)

Appendices

Scheduled Maintenance

Index

Quick Links

Related Manuals for Ford Econoline E-150

Summary of Contents for Ford Econoline E-150