Part Description - Panasonic EX-F70 SERIES Ordering Manual

859
Leak Detection Sensor
PRECAUTIONS FOR PROPER USE
FIBER
SENSORS
LASER
EX-FC1
SENSORS
PHOTO- Mounting
ELECTRIC
SENSORS
• When mounting the unit, be sure to use the unit mounting
MICRO
PHOTO-
base (MS-SL-2) (accessory).
ELECTRIC
SENSORS
• When installing the unit mounting base to the unit, insert
AREA
SENSORS
the base aligned with the grooves of the unit and move
until the unit stopper is locked.
LIGHT
CURTAINS
PRESSURE /
FLOW
SENSORS Grooves
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
• Two installation positions are available for the unit
SIMPLE
WIRE-SAVING
UNITS
mounting base so that the unit direction can be changed.
WIRE-SAVING Install the base at one of them.
SYSTEMS
MEASURE- Mounting position 1
MENT
SENSORS
Unit
STATIC
CONTROL
DEVICES
ENDOSCOPE
LASER
MARKERS
Unit mounting base
PLC /
Din rail stopper
TERMINALS
HUMAN
MACHINE
˂In case of using a DIN rail or the mounting bracket (MS-DIN-3)
INTERFACES
(optional) ˃
ENERGY
CONSUMPTION
VISUALIZATION
Fit the rear part of the unit
COMPONENTS
mounting base on a 35 mm
FA
1.378 in width DIN rail or
COMPONENTS
the mounting bracket
MACHINE
VISION (MS-DIN-3) (optional).
SYSTEMS
Press down the front part
UV
CURING
of the unit mounting base
SYSTEMS
on the 35 mm 1.378 in
width DIN rail and fit the
front part of the base on
the DIN rail.
Selection
Guide
Wafer
* For removal, insert a
Detection
Liquid Leak flathead screwdriver into
Detection
the DIN rail stopper and
Liquid Level
Detection
pull towards yourself.
Water
Detection
Color Mark
Detection
˂In case of using screws˃
Hot Melt Glue
Detection • Mount using M4 pan head
screws with a tightening
Ultrasonic
torque of 0.8 N·m or less.
Small / Slim
Object Detection
However, in case of side
Obstacle
Detection
mounting, make sure to
Other
mount the unit such that
Products
the unit stopper faces
front.
SQ4
EX-F70/
EX-F60
EX-F70 EX-F60
SERIES
Unit stopper
Mounting position 2
Unit
Unit mounting base
Din rail stopper
DIN rail stopper
35 mm 1.378 in width DIN rail or the
mounting bracket (MS-DIN-3) (Optional)
Flathead screwdriver
DIN rail stopper
M4 pan head screw
Unit
(
Purchase
separately.
Unit stopper
Unit mounting
base
SERIES

Part description

Designation
Normal indicator
(Green LED × 8)
Error indicator
(Red LED × 8)
Output indicator
(Orange LED)
Connection setting
switch
Connector
Connection
• Make sure to connect or disconnect the snap male
connector (SL-CP1) in the power supply off condition.
• Take care that wrong wiring will damage the product.
• The terminal No. 4 of the snap male connector
(SL-CP1) is not used.
Take care not to connect to the terminal No. 4 by
mistake. Further, if there are unused wires, please
insulate them.
1 1 2 2 3 3
• For details of the hook-up method of the snap male
connector (SL-CP1), refer to the Instruction Manual
enclosed with SL-CP1.
Connection method
)
• By holding the SL-CP1 with
the cable connected, insert it
into the connector of the
EX-FC1 reliably till it stops.
Disconnection method
• By holding SL-CP1, pull it
from the EX-FC1 horizontally.
Note: Do not pull out by holding the
cable, as this can result in cable
disconnection.
Refer to General precautions.
Function
Lights up when sensors are connected to each channel
and the connection setting switch is set to ON.
Lights up when leak is detected by any sensor
connected or any sensor is mounted improperly.
(For details, refer to "Connection setting
Lights up when the output relay is ON (Normal).
Set the switch to ON when the leak detection
sensor is connected, set to OFF when the leak
detection sensor is not connected.
Connect the leak detection sensors.
Content
+V
4 4 0 V
IN
No connected
EX-FC1
SL-CP1 ( Accessory )
Cable of the leak
detection sensor
switch".)