Loewe Individual 32 Selection Operating Instructions Manual page 13

Initial installation
Explanations of the setting possibilities, including the upgradeable satellite reception:
Decide how energy efficiently you want to operate your
Energy
TV set. The value for the contrast (and thus the brightness
efficiency
of the background lighting) is adapted and the automatic
dimmer activated or deactivated (see page 22) depending
on the presetting.
Eco standard:
The emphasis for home use is on low energy consumption.
The automatic dimmer is activated.
Premium mode:
This mode optimises the settings to a brighter environment
at a higher energy consumption. The automatic dimmer
is activated.
Shop mode:
The picture settings are aligned to operation in the presen-
tation room. The automatic dimmer is deactivated. If the
ambient brightness diminishes, the energy consumption
is not reduced.
The presetting can be changed later in the TV menu under
Picture Picture adjustment
under Settings
Location Select the country for country-specific pre-settings.
of TV set
If UK or IRL is selected for the location of TV set, it is pos-
sible to activate MHEG-5 (UK Freeview) for the TV set.
If MHEG-5 was activated, DVB-C and DVB-S can not be
used anymore. Only terrestrial/cable and DVB-T stations
are available.
Caution: Common Interface Plus technology will never
work again after activating MHEG-5.
A dialogue appears, where you can confirm to set the
operating software to the selected location.
If Yes is selected and confirmed with OK, the TV set turns
off and on again automatically. First installation starts again
after activating the operation software.
Antenna Antenna/cable (analogue): analogue stations via
selection
DVB-T:
DVB-C:
DVB-S (cable 1):
DVB-S (cable 2):
You can preset the desired languages and reserve lan-
Subtitle and
audio languages guages for subtitles and audio for DVB programmes here
(DVB) (see page 42).
Logical In various countries, digital stations (DVB-T, DVB-C) are
transmitted with a preset channel number per station,
Channel
Number known as "Logical Channel Numbers" – "LCN". In this
case the preset channel numbers are adopted as station
memory locations and the stations of the preferred signal
source sorted according to LCN. There may be gaps in
the numbering of the station list depending on the LCN.
Presettings (see page 22) or
Energy efficiency.
cable/antenna
digital terrestrial stations
digital stations via cable
digital stations via satellite
digital stations via satellite
Logical For TV sets with MHEG-5 software the stations are tied
Channel to "Logical Channel Numbers" – "LCN" and sorted from
Number 1-799. Digital stations without "LCN" are stored from
(continued) 800 onwards. Analogue stations are stored from 1001.
Encrypted You can state whether coded stations are to be searched
stations for in the search/update.
scrambled stations. However, these stations can only
be received in connection with a CA module and the
appropriate Smart Card.
described on page 40.
If a CA module with a SmartCard is already plugged in for
the station search, all the stations which this module can
descramble are also saved when no is preset.
DVB-T: If you are using an active antenna, then select yes (5V)
Antenna for the antenna power supply.
DVB-C: The conventional settings will be derived from the selec-
Settings tion of set location. Only change this if you know other
symbol rates and modulation types or if you have to
specify the network ID for your cable network. In the
case of small cable networks fed directly from the satel-
lite, the rate of 6900 might have to be replaced by 6111.
Information is available from your cable network provider.
If you want to run the station search independently of
the channel grid, select frequency search for the search
method.
DVB-S: State how (single satellite or type of satellite system) you
Satellite receive which satellite(s). Ask your dealer if in doubt.
system
High band Specify here whether the high band of the selected satel-
lite is to be searched in addition to the low band.
LNC Normally, you do not need to change the values for high
frequencies and low band, unless the LNC (LNB) of your satellite
Low Band / system uses a different oscillator frequency (important
High Band for the frequency display).
After you have made these settings, you should receive
the picture and sound of the selected satellites (only with
Astra1 and HOTBIRD).
Search If you want to run the station search independently of
method the channel grid, select frequency search for the search
method.
Symbol rates The symbol rates are specified by the satellite provider
and do not normally need to be changed.
Favoured Select the signal source from a list, the station of which is to
signal source be at the top of your station list (starting with station slot 1).
Recordings with automatic time control (see page 55) are
only possible for the respective first DVB signal source.
Select yes to save all found
Handling of the CA module is
p
continued on next page
13 -