Advertisement
When the temporary hold timer counts down to zero, the set
points will change to the program schedule settings for that
time of day. If smart recovery conditions are satisfied, the set
points will change from the occupied values to the program
schedule values.
If Hold is active, the temporary hold timer is not displayed.
The fan will run according to the setting specified by the in-
staller in configuration option 36.
When Holiday is active and the OCCUPIED button is
pressed, the temporary hold timer is set for two hours, the heat
and cool set points change to the occupied settings, the humidi-
ty control will use the "normal" (not holiday) settings, and the
fan will run according to the setting specified by the installer in
configuration option 36.
If the remote indoor temperature sensor with override (part
no. 33ZCT55SPT) is used, it will function the same as the local
OCCUPIED button except that the button press will be inactive
if the thermostat is in hold. The remote OCCUPIED button is
located on the left-hand side of the sensor. Press and hold the
button for at least two but not longer than five seconds to re-
quest an occupied override.
Programming Schedules —
®
thermostats, the Edge
Pro thermostat gives the user the option
of programming every day of the week differently. The ther-
mostat is preprogrammed at the factory with the same settings
for all seven days. See Table 1.
Table 1 — Schedule Factory Settings
START
PERIOD
TIME
Occ
6 AM
Occ2
8 AM
Occ3
3 PM
Unocc
6 PM
To set up a different schedule where all the days are the
same, perform the following:
1. Open the thermostat door.
2. Press the SET button until the screen displays "daily
schedule" in the center of the screen. The list of the days
of the week are displayed on the left. The arrows next to
each day indicate that all seven days will be programmed
the same way.
3. The arrow will be pointing to "occ" on the screen. To set
the occ period start time, press the soft key under the hour
or minute indicator and then press the UP or DOWN but-
ton to change the time.
4. Set the heating temperature set point for that time period
by pressing the soft key under the heat set point tempera-
ture. Press the UP or DOWN button until the desired
heating temperature is shown.
5. Set the cooling temperature set point for that time period
by pressing the soft key under the cool set point tempera-
ture. Press the UP or DOWN button until the desired
cooling temperature is shown.
6. Repeat this process for each of the three remaining time
periods (occ2, occ3, and unocc) by first pressing the soft
key under the time period to select it with the arrow.
Then use the soft keys to change the start time, the heat-
ing set point, and the cooling set point.
7. Press the DONE button when complete.
8. Close the thermostat door.
To set up a schedule where all days of the week will not fol-
low the same schedule, perform the following:
1. Fill in Table 2 with the desired times and set points for
each day. Use this table as a guide during programming
and for future reference.
Unlike
many
other
HEAT SET
COOL SET
POINT
POINT
68
78
68
78
68
78
60
85
2. Open the thermostat door.
3. Press the SET button until the screen displays "daily
schedule" in the center of the screen. The list of the days
of the week are displayed on the left.
4. There will be arrows next to each day. This indicates that
all seven days will be programmed the same way. Press
the soft key under the days of the week until the arrow is
next to the day that will be programmed.
5. The arrow will be pointing to "occ" on the screen. To set
the occ period start time, press the soft key under the hour
or minute indicator and then press the UP or DOWN but-
ton to change the time.
6. Set the heating temperature set point for that time period
by pressing the soft key under the heat set point tempera-
ture. Press the UP or DOWN button until the desired
heating temperature is shown.
7. Set the cooling temperature set point for that time period
by pressing the soft key under the cool set point tempera-
ture. Press the UP or DOWN button until the desired
cooling temperature is shown.
8. Repeat this process for each of the three remaining time
periods (occ2, occ3, and unocc) by first pressing the soft
key under the time period to select it with the arrow. Then
use the soft keys to change the start time, the heating set
point, and the cooling set point.
9. Press the soft key under the days of the week until the ar-
row is pointing to the next day that will be programmed.
10. Repeat Steps 5 to 8 to program the current day.
11. Repeat this process until all the days have been pro-
grammed.
12. Press the DONE button when complete.
13. Close the thermostat door.
Table 2 — Daily Schedule Planner
DAY
Occ
Start/Heat/Cool Start/Heat/Cool Start/Heat/Cool Start/Heat/Cool
Mon
/
/
Tue
/
/
Wed
/
/
Thu
/
/
Fri
/
/
Sat
/
/
Sun
/
/
NOTE: The cooling temperature set point must be higher than the heating
temperature set point. (The temperature difference may be changed in the
advanced set up configuration by the installer.)
Programming a Holiday Schedule —
can program a special heating and cooling schedule to follow
during holidays or extended absences. To program the holiday
schedule, perform the following:
1. Open the thermostat door.
2. Press the SET button until the screen displays the holiday
settings.
3. Set the heating temperature set point for the holiday by
pressing the soft key under the heat set point temperature.
Press the UP or DOWN button until the desired heating
temperature is shown.
4. Set the cooling temperature set point for the holiday by
pressing the soft key under the cool set point temperature.
Press the UP or DOWN button until the desired cooling
temperature is shown.
3
SCHEDULE
Occ2
Occ3
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
Unocc
/
/
/
/
/
/
/
/
/
/
/
/
/
/
The user
Advertisement
