Installer Menu - LG Pro Centric 37LT777H Commercial Mode Setup Manual

Installer Menu (Cont.)
119 - DATA CHANNEL
Set to 0 to disable. Set from 1 to 135 to match the RF channel
number that will be used by the Pro:Centric server as its data
channel. *
For TVs in Pass-through Mode or FTG Mode via CPU, if this item
is left at its default value (255), the TV's Data Channel Auto Search
feature will be enabled (see additional information below).
Note: The Data Channel Auto Search feature is not available
when the TV's EBL is in FTG Mode. If the DATA CHANNEL value
is 255 when the TV is configured for FTG Mode via EBL, DATA
CHANNEL is defaulted to 0.
Data Channel Auto Search feature: When this item is set to 255
(default), once every 24 hours, the TV will initiate a search of 10
predefined channels (10, 20, 30, ... 100) and then, if necessary,
perform a complete search of the RF channels (1 to 135) in an
attempt to find the RF channel used by the Pro:Centric server as
its data channel. If the Pro:Centric RF channel is found, the DATA
CHANNEL value will be changed from 255 to match the server's
RF channel number. The time at which the Auto Search occurs
depends on the setting of item 121 UPDATE TIME HR. See item
121 description for further information.
Note: Pro:Centric application updates are downloaded from the
Pro:Centric server to the TV when the TV is turned ON; however,
TV E-Z Installation updates are downloaded to the TV when the TV
is turned OFF. While E-Z Installation updates are in progress, it is
not possible to turn ON the TV.
Note: The Data Channel is automatically set to "253" if Media
Type is set to "IP" either in the EZ-Manager Wizard or in the IP
Environment / Pro:Centric Menu on the TV (see "EZ-Manager
Wizard" on pages 11 to 18 or "Pro:Centric Setup" on page 60,
respectively) or if the Data Channel Installer Menu item is set to
"IP Address" in the FTG File Manager, which is used to configure
TV CPUs for FTG Mode operation. It is not possible to change the
value to "253" directly in the Installer Menu.
121 - UPDATE TIME HR
Set the Wake For Update hour from 0 to 23. This item uses the
24-hour clock format. The value "128" is displayed as "OFF."
Directly entering 128 turns the Wake For Update feature OFF.
The Wake For Update feature uses a timer, based on the settings
of this item and item 122 UPDATE TIME MN, to "wake" the TV to
check for and, if applicable, download updates from the Pro:Centric
server.
*
PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.
30
Under standard TV turn OFF/ON operating conditions (i.e., item
002 AC ON is set to 0), a Wake For Update event occurs when
the TV is OFF. The Wake For Update event temporarily turns the
TV ON, completes the update cycle, and then turns the TV back
OFF. If item 002 AC ON is set to 2 or 3 for Instant ON, Wake For
Update occurs when the TV is in its Muted ON state (i.e., the TV
only appears to be OFF). The Wake for Update event initiates a
TV reboot in order to start the update cycle and then, when the
update cycle is complete, the TV returns to its Muted ON state.
If the TV display is ON when a Wake For Update event is due to
occur, the Wake For Update will take place the next time the TV is
turned OFF. See also description for item 002.
If Wake For Update is OFF, the time at which either a Data
Channel Auto Search (item 119 set to 255) and/or an Instant ON
update (item 002 set to 2 or 3) occurs is determined as follows:
The TV will initiate the search and/or check for updates at 2:00
PM (if the TV clock is set) or at 14 hours of elapsed time from
when AC power was applied (if the TV clock is not set). If the TV
display is ON when Wake For Update is to occur, the Wake For
Update will take place the next time the TV is turned OFF.
Note: This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0, except when item 002 AC ON is
set to 2 or 3 for Instant ON.
Note: The TV clock must be set in order for a Wake For Update
event to occur at the precise time of day in accordance with item
121 and item 122 settings.
122 - UPDATE TIME MN
Set the Wake For Update minute from 0 to 59. See also description
for item 121 UPDATE TIME HR above.
Note: This item is not available in the Installer Menu unless item
121 UPDATE TIME is set from 0 to 23.
Note: The TV clock must be set in order for a Wake For Update
event to occur at the precise time of day in accordance with item
121 and item 122 settings.
206-4234