Advertisement
GPSMAP
700 Series Installation Instructions
®
WARNING
See the Important Safety and Product Information guide in the product box for product warnings and other important information.
CAutIoN
Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
Notice
When drilling or cutting, always check what is on the opposite side of the surface to avoid damaging your boat.
The GPSMAP 700 series chartplotter must be properly installed according to the following instructions. You need the appropriate fasteners,
tools, and mounts listed in each section. These items are available at most marine dealers.
Contact Garmin
Product Support if you have any questions while installing your GPSMAP 700 series chartplotter. In the USA, go to
www.
®
garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020. In the UK, contact Garmin (Europe) Ltd. by phone
at 0808 2380000. In Europe, go to
www.garmin.com/support
and click
Contact Support
for in-country support information, or contact Garmin
(Europe) Ltd. by phone at +44 (0) 870.8501241.
Before installing your GPSMAP 700 series chartplotter, confirm that the package contains the items listed on the box. If any parts are missing,
contact your Garmin dealer immediately.
Product Registration
Help us better support you by completing our online registration today. Go to http://my.garmin.com. Keep the original sales receipt, or a
photocopy, in a safe place.
For future reference, write the serial number assigned to your GPSMAP 700 series chartplotter in the space provided. The serial number is
located on a sticker on the back of the device.
Chartplotter serial number:
to install the GPSMAP 700 series chartplotter, you must:
1. Mount the GPSMAP 700 series chartplotter.
2. Connect the chartplotter to power (page 5).
3. Ensure that the chartplotter software is up-to-date (page 7).
the following additional installation options are not necessary in order to use the GPSMAP 700 series chartplotter. they have
been included for your convenience:
• Connecting the chartplotter to a NMEA 2000 network (page 6)
• Connecting the chartplotter to a GA 30 remote GPS antenna (page 6).
• Connecting the chartplotter to a Garmin marine radar (page 6).
• Connecting the chartplotter to other NMEA 0183-compatible devices such as a VHF radio with DSC (page 5).
• Connecting the chartplotter to a sonar transducer ("s" models only) (page 6).
Mounting the Chartplotter
You can mount the GPSMAP 700 series chartplotters using one of two methods. You can use the included bracket and hardware to bail mount
the chartplotter, or you can use the included template and hardware to flush mount the chartplotter.
Mount the GPSMAP 700 series chartplotter in a location that provides a clear, glare-free view of the display and easy operation of the power
key and the touch screen.
February 2010
Part Number 190-01155-02 Rev. B
Printed in Taiwan
Advertisement
Table of Contents
Related Manuals for Garmin GPSMAP 190-01155-02
Summary of Contents for Garmin GPSMAP 190-01155-02
-
Page 1: Product Registration
Product Support if you have any questions while installing your GPSMAP 700 series chartplotter. In the USA, go to www. ® garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020. In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000. In Europe, go to www.garmin.com/support... - Page 2 GA 30 GPS antenna cable clip GA 30 GPS antenna cable clip Power/data cable clip Power/data cable clip Garmin Marine Radar cable clip Garmin Marine Radar cable clip NMEA 2000 cable clip NMEA 2000 cable clip GPSMAP 700 Series Installation Instructions...
- Page 3 NotE: If you are mounting the chartplotter in fiberglass, it is recommended to use a countersink bit to drill a clearance-counter bore through only the top gel-coat layer. This will help to avoid any cracking in the gel-coat layer when the screws are tightened. 4. Remove the bail-mount bracket template from the mounting surface. 5. Secure the bail mount to the surface using the four included 35 mm M 4.2 × 1.4 screws. NotE: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainless anti-seize lubricant to the screw before using. to install the GPSMAP 700 series chartplotter on the bail-mount bracket: 1. Loosely attach the mounting knobs to the GPSMAP 700 series chartplotter.
- Page 4 Installing the Power/Data Cable The chartplotter comes with a power/data cable that connects the chartplotter to power and to optional NMEA 0183 devices. If applicable, the power/data cable also connects the chartplotter to a sonar transducer. The power/data cable does not connect the chartplotter to a NMEA 2000 network. For instructions on connecting the chartplotter to a NMEA 2000 network, see To help make the cable-routing process easier, the locking ring is packaged separately from the cable.
- Page 5 Wiring a GPSMAP 700 Series Chartplotter to a Standard NMEA 0183 Device to connect the power/data cable to a NMEA 0183 device: 1. For Garmin devices, the ground (black) wires serve as NMEA 0183 ground and must be attached together or on the same terminal as the NMEA 0183 ground on your NMEA 0183 device. Refer to the wiring diagram of your NMEA 0183 device for wire identification.
- Page 6 2. Route the GA 30 cable to the chartplotter, and connect it to the external GPS antenna connector. Connecting the Chartplotter to a transducer If you have a sonar-cable GPSMAP 700 series chartplotter (indicated by an “s” in the product name), you can connect a Garmin transducer to use sonar-specific features. to connect the chartplotter to a transducer: 1. Install the transducer according to the instructions provided with the transducer.
-
Page 7: Updating The Chartplotter Software
Identifying the Rear-Panel Connectors After the power/data cable is wired to the boat (and after any optional Garmin radar, NMEA 0183, NMEA 2000, or external GPS devices are installed) connect the cables to the GPSMAP 700 series chartplotter. NOTE: You must install the locking rings before connecting the power/data cable or a Garmin radar cable to the chartplotter to connect a cable to the back of a GPSMAP 700 series chartplotter: 1. -
Page 8: Physical Specifications
Specifications Physical Specifications Specification Measurement Size W × H × D: 8 × 5 × 3 Weight 2.48 lb. (1.125 kg) Display W × H: 6 × 3 in. (152 × 91 mm) Case Fully Gasketed, high-impact plastic and aluminum alloy, waterproof to IEC 60529 IPX-7 Temp. Range From 5°F to 131°F (from -15°C to 55°C) Compass Safe 32 in. (813 mm) Distance GPS Performance Specification Parameter Measurement Receiver High-sensitivity 12 parallel channel, WAAS-capable receiver Acquisition Warm Approximately 1 sec. (The device is at or near the last location at which you recently acquired satellites.) Time Cold... -
Page 9: Nmea 0183 Information
Receive 128259 Speed - Water Referenced 128267 Water Depth 129038 AIS Class A Position Report 129039 AIS Class B Position Report 129040 AIS Class B Extended Position Report 129794 AIS Class A Static and Voyage Related Data 129798 AIS SAR Aircraft position report 129799 Radio Frequency/Mode/Power 129802 AIS Safety Related Broadcast Message 129808 DSC Call Information 130306 Wind Data 130576 Small Craft Status 130310 Environmental Parameters 130311 Environmental Parameters (Obsolete) 130312 Temperature 130313 Humidity 130314 Actual Pressure NMEA 0183 Information NMEA 0183, Version 3.01 Sentences: Receive Depth Depth Below Transducer... - Page 10 Garmin , the Garmin logo, GPSMAP , and AutoLocate are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. GMR™ is a trademark of ® ® ® Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin.