Table of Contents
Advertisement
Heat Controller, Inc.
SERVICE ACCESS
3' (91 CM)
FRONT AND BACK
Overall Cabinet
Model
A
B
Depth
Width
Height
084
in.
34.0
53.1
79.0
-120
cm.
86.4
134.9
200.7
in.
34.0
53.1
79.0
150
cm.
86.4
134.9
200.7
HKV LArge CommerCiAL
ALL CONFIGURATIONS REQUIRE SERVICE ACCESS AREA SHOWN BELOW. (RR/FD)
F
7.6
AIR OUT
BSP
NRP
RETURN AIR
S
C
1
Q
3
CAP+MSP
02
Control Box
P
01
2
CSP
REAR RETURN TOP DISCHARGE
LEGEND
Water Inlet (See Note 2)
1
2
Water Outlet (See Note 2)
Condensate Drain (See Note 3)
3
4
High Voltage Access (See Note 4)
5
Low Voltage Access (See Note 4)
BSP - Blower Service Panel
CAP - Control Access Panel
CSP - Compressor Access Panel
MSP - Motor Service Panel
NRP - Non Removable Panel
1.7
F
D
RETURN AIR
BSP
E
BSP
AIR OUT
NRP
4
NRP
1
5
3
4
CAP+MSP
Control Box
2
CSP
NOTES:
- All dimensions in inches (cm)
- Units require 3' (9.1 cm) clearance for water connections, CAP, CSP, MSP and BSP service access.
- Overall cabinet height dimension does not include duct flange when in top discharge configuration.
- Overall cabinet width dimensions does not include filter rack and duct flange when on front or back discharge configuration.
- Side service access must be 3 feet (91 cm) on either side that connections are made. If no connections are made on a side
then service access can be 6 inches (1.5 cm) minimum.
Discharge Connections
Duct Flange
C
D
E
F
Supply
Supply
Water
Width
Depth
17.5
17.6
17.8
31.0
44.5
44.6
45.1
78.7
21.4
17.6
17.8
31.0
54.4
44.6
45.1
78.7
7.6
B
D
NRP
NRP
R
4
5
R
U
NRP
4
Control Box
3
3
N
NRP
M
K
L
A
NOTES FOR LEGEND:
1. While access to all removable panels is not required, installer
HKV084-120
TLV084-120
HKV150
TLV150
should take care to comply with all building codes and allow
1-1/2" FPT
2" FPT
adequate clearance for future field service.
1-1/2" FPT
2" FPT
1" FPT
2. Water inlet and water outlet connections are available on either
1-3/8" [3.49 CM]
side (left or right) of the unit. Qty (2x) MPT Plugs are shipped loose
7/8" [2.2 CM]
in a plastic bag tied to the water leg in front of the unit. Installer must
plug water inlet/outlet side not being connected to.
3. Condensate drain is available on either side (left or right) of unit.
Drain hose and drain connection will be tied inside the unit. Installer
will untie the drain hose and connect to the condensate drain hole of
installer's choice.
4. Electrical access is available on either side (left or right) of unit and
is also available (left or right) in the front of the unit.
4
5
NRP
4
Control Box
3
3
4
5
NRP
4
CSP+CAP+MSP
SIDE
SERVICE ACCESS
(SEE NOTE)
REAR RETURN FRONT DISCHARGE
Water Connections
K
L
M
N
O1
1
1
3
Water
Con-
Inlet
Outlet
densate
3.0
27.0
25.6
31.0
7.6
68.6
65.1
78.7
3.0
27.0
25.6
31.0
7.6
68.6
65.1
78.7
4
HKV084-150 Dimensional Data
F
AIR OUT
BSP
RETURN AIR
2
NRP
4
3
5
4
L
1
M
K
CSP+CAP+MSP
FRONT RETURN TOP DISCHARGE
F
BSP
AIR OUT
RETURN AIR
NRP
2
4
3
5
4
1
FRONT RETURN REAR DISCHARGE
Electrical Knockouts
O2
P
Q
R
S
Return
Depth
38.0
34.6
1.0
3.0
48.0
96.4
87.7
2.5
7.6
121.9
38.0
34.6
1.0
3.0
48.0
96.4
87.7
2.5
7.6
121.9
IOM Instructions
Return Air Connections
Using Return Air Opening
T
U
V
W
Return
Height
32.4
44.6
2.7
2.0
82.2
113.3
6.9
5.1
32.4
44.6
2.7
2.0
82.2
113.3
6.9
5.1
Advertisement
Table of Contents
Troubleshooting
