Cycle Status Indicators; Active Vent; Overfill Protection Float - Kenmore Elite Ultra Wash 665.1628 Series Use And Care Manual

NOTE: Sani Rinse is an option with SMART
WASH
TM,
Pots Pans,
and Normal Wash cycles. Only these sanitization cycles have
been designed to meet the NSF/ANSI requirements,
Heated Dry
The Heated Dry option in combination with rinse aid will give you
excellent drying results. The energy to use Heated Dry costs
pennies per cycle. Heated Dry is on when the light is lit on the
Heated Dry button. Be sure to load plastic items in the upper rack
to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY
so that the light goes off. However, you will have items in your
dishload that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Quick
Rinse.
Lock On
Use the Lock On to prevent unintended use of the dishwasher
between cycles.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.
Delay Hours/4 Hour Delay
Select this option to run your dishwasher at a later time or during
off-peak hours. You can add items to the load anytime during the
delay. After adding items, press START/RESUME. Make sure the
door is latched or the delay will not continue.
To delay the start
1. Press the delay button to choose the number of hours
delayed.
2. Select a wash cycle and options.
3. Press START/RESUME.
The dishwasher starts the cycle in the selected number of hours.
NOTES:
• To cancel the delay and cycle, press CANCEL/DRAIN.
To cancel the delay and start the cycle, press START/
RESUME.
On top control models, if the door is not closed within
3 seconds of pressing Start/Resume, press START/RESUME
again.
Sanitized
If you select the Sani Rinse option, Sanitized glows when the
Sani Rinse cycle is finished. If your dishwasher did not properly
sanitize your dishes, the light flashes at the end of the cycle. This
can happen if the cycle is interrupted or the incoming water
temperature is too low. The light turns off when you press any
button or close the door.
Clean
Clean glows when a cycle is finished. The light turns off when you
press any button or close the door.
(On top control models)
The active vent reduces the sounds from your dishwasher. The
vent closes, after the cycle starts, to lock in sound. After the
cycle finishes and the dishes cool for several hours, the vent
opens. This prevents any water vapor from collecting on the
countertop. Between cycles, the vent stays open for airflow,
reducing the buildup of odors.
NOTE: There is a slight noise when the vent closes or opens. This
is normal.
(On split control models)
The active vent reduces the sounds from your dishwasher. The
vent closes, after the cycle starts, to lock in sound. The Active
Vent opens when wash action ends and vapor is vented into
room. Between cycles, the vent stays open for airflow, reducing
the buildup of odors.
NOTE: There is a slight noise when the cover closes or opens.
This is normal.
IMPORTANT: The vapor is hot. Do not touch the vent
during drying.
_,al •
,-\ .•.,
-..._)_-.
Follow the progress of your dishwasher with the Cycle Status
indicators.
WASHING DRYING CLEAN
NOTE: The features on your dishwasher may vary from those
shown here.
The overfill protection float (in the front right corner of the
dishwasher tub) keeps the dishwasher from overfilling. It must be
in place for the dishwasher to operate.
Check under the float for objects that may keep the protector
from moving up or down.
17