Page 2 TRADEMARKS IMPORTANT: READ BEFORE DOWNLOADING, COPYING, INSTALLING OR USING. By downloading, copying, installing or using the software you agree to this license. If you do not agree to this license, do not download, install, copy or use the software. Intel License Agreement For Open Source Computer Vision Library Copyright ©...
Page 3: Introduction
INTRODUCTION INTRODUCTION Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT SAFETY INSTRUCTIONS”, and then study this manual for the correct operation of the various functions. In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference.
Page 4 • In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of the operation manual to inspect and adjust the machine yourself. If the problem persists, please consult your local authorized Baby Lock retailer. Use this machine only for its intended use as described in the manual.
Page 5 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This machine is intended for household use. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Page 6 1760 Gilsinn Lane, Fenton, Missouri 63026 USA declares that the product Product Name: Baby Lock Sewing Machine Model Number: BLAR This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 7: What You Can Do With This Machine
WHAT YOU CAN DO WITH THIS MACHINE WHAT YOU CAN DO WITH THIS MACHINE Basic operations After purchasing your machine, be sure to read this section first. This section provides details on the initial setup procedures as well as descriptions of this machine’s more useful functions. Chapter 1 Getting Ready To learn the operation of the principal parts and the screens...
Page 8: Table Of Contents
CONTENTS CONTENTS TRADEMARKS STITCH SETTINGS ..........10 INTRODUCTION ..........1 Setting the Stitch Width ............10 Setting the Stitch Length............11 IMPORTANT SAFETY INSTRUCTIONS ....1 Setting the “L/R SHIFT” ............11 WHAT YOU CAN DO WITH THIS MACHINE ..5 Setting the Thread Tension...........
Page 9 CONTENTS COMBINING STITCH PATTERNS ...... 90 Before Combining ..............90 Combining Various Stitch Patterns ........90 Combining Large and Small Stitch Patterns ......91 Combining Horizontal Mirror Image Stitch Patterns ..... 92 Combining Stitch Patterns of Different Length ...... 92 Making Step Stitch Patterns (for 7mm Satin Stitch Patterns Only)........
Page 10: Names Of Machine Parts And Their Functions
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS NAMES OF MACHINE PARTS AND THEIR FUNCTIONS The names of the various parts of the sewing machine and their functions are described below. Before using the sewing machine, carefully read these descriptions to learn the names of the machine parts. Machine ■...
Page 11: Needle And Presser Foot Section
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Needle and Presser Foot Section Measurements on the needle plate, bobbin cover (with mark) and needle plate cover The measurements on the needle plate and bobbin cover are references for patterns with a middle (center) needle position.
Page 12: Operation Buttons
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Operation Buttons CAUTION • Do not press the thread cutter button after the threads have been cut. The needle may break and threads may become tangled, or damage to the machine may occur. Using the Flat Bed Attachment Pull up on the lid of the flat bed attachment to open the front or back accessory compartments.
Page 13: Included Accessories
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Included Accessories 75/11 2 needles 2.0/11 needle 90/14 2 needles 90/14 2 needles: Ball point needle (gold colored) Part Name Part Code Part Name Part Code 11 1/4” quilting foot with guide XC6800-251 Zigzag foot “J”...
Page 14: Options
NAMES OF MACHINE PARTS AND THEIR FUNCTIONS Part Name Part Code Part Name Part Code 21 Eyelet punch XZ5051-001 38 Bobbin cover (with mark) (on XF0750-101 machine) 22 Screwdriver (small) X55468-051 39 Bobbin cover XE8992-101 23 Screwdriver (large) XC4237-021 40 Foot controller XC8816-051 24 Disc-shaped screwdriver XC1074-051...
Page 15: Basic Operations
Basic operations This section provides details on the initial setup procedures as well as descriptions of this machine’s more useful functions. Page number starts with “B” in this section. Chapter1 Getting Ready ............B-14...
Page 16 BBasic operations Chapter Getting Ready TURNING THE MACHINE ON/OFF ......15 Setting Your Machine for the First Time ........16 LCD SCREEN............18 ■ Utility Stitch Screen ..............18 ■ Key Functions................19 Using the Machine Setting Mode Key ........21 ■ Selecting the “Eco Mode” or “Shutoff Support Mode”..... 24 ■...
Page 17: Turning The Machine On/Off
TURNING THE MACHINE ON/OFF TURNING THE MACHINE ON/OFF WARNING • Use only regular household electricity for the power source. Using other power sources may result in fire, electric shock, or damage to the machine. • Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power cord receptacle on the machine.
Page 18: Setting Your Machine For The First Time
TURNING THE MACHINE ON/OFF Insert the power supply cord into the power Turn the main power switch to “O” to turn cord receptacle, then insert the plug into a off the machine. wall outlet. Memo • If the machine is turned off in the middle of sewing in the “Sewing”...
Page 19 TURNING THE MACHINE ON/OFF Press to set time/date. a Press to display the time on the screen. b Set the year (YYYY), month (MM) and date (DD). c Select whether 24h or 12h setting to display. d Set the current time. Press to start using your machine.
Page 20: Lcd Screen
LCD SCREEN LCD SCREEN CAUTION • Only touch the screen with your finger or the included touch pen. Do not use a sharp pencil, screwdriver, or other hard or sharp object. It is not necessary to press hard on the screen. Pressing too hard or using a sharp object may damage the screen.
Page 21: Key Functions
LCD SCREEN Display Key Name Explanation Page Scroll key – Press , to move one page at a time, or touch anywhere on the bar to jump ahead for additional pages of stitches. All key functions of the LCD are explained in the “Key Functions” table on the following page. ■...
Page 22 LCD SCREEN Display Key Name Explanation Page Presser foot/Needle Press this key before changing the needle, the presser foot, etc. This key locks B-45 to exchange key all key and button functions to prevent operation of the machine. B-48 Sewing machine help Press this key to see explanations on how to use the machine.
Page 23: Using The Machine Setting Mode Key
LCD SCREEN Using the Machine Setting Mode Key Press to change the default machine settings (needle stop position, opening display, etc.). Memo • Press next to the page numbers, to display a different settings screen. a Select whether to use the sewing speed controller to determine the zigzag width (see page S-39). b Make adjustments to character or decorative stitch patterns (see page S-82).
Page 24 LCD SCREEN m Select the needle stop position (the needle position when the machine is not operating) to be up or down. Select the down position when using the pivot key. (see page S-15) n Select the operation of the “Needle Position – Stitch Placement” button from the following two sequences (see page S-18).
Page 25 Display the program version. “Version 1” shows the program version of the LCD panel, “Version 2” shows the program version of the machine. Memo • Check with your local authorized Baby Lock retailer or at “ www.babylock.com ” for the current version update ( see page A-20...
Page 26: Selecting The "Eco Mode" Or "Shutoff Support Mode
LCD SCREEN ■ Selecting the “Eco Mode” or ■ Changing the Pointer Shape When a “Shutoff Support Mode” USB Mouse Is Used You can save the machine power by setting the eco In the settings screen, the shape can be selected for mode or the shutoff support mode.
Page 27: Selecting The Initial Screen Display
LCD SCREEN ■ Selecting the Initial Screen Display ■ Saving a Settings Screen Image to USB Media The Initial screen that appears on the machine can be changed. An image of the settings screen can be saved as a BMP file. Press A maximum of 100 images can be saved on a single →...
Page 28: Using The Sewing Machine Help Key
LCD SCREEN Using the Sewing Machine Help Key Press to open the sewing machine help screen. Three functions are available from the screen shown below. a Press this key to see explanation for upper threading, winding the bobbin, changing the presser foot, how to use the machine, troubleshooting and maintenance (see page B-27).
Page 29: Using The Operation Guide Function
LCD SCREEN Using the Operation Guide Function Press to open the screen shown below. Five categories are displayed at the top of the screen. Press a key to see more information about that category. displays information about displays information about displays information about the main parts of the machine and their the operation buttons.
Page 30: Using The Sewing Guide Function
LCD SCREEN Example: Displaying information about Using the Sewing Guide Function upper threading Press The sewing guide function can be used to select patterns from the Utility Stitch screen. Press Use this function when you are not sure which stitch to use for your application, or to get advice about sewing particular stitches.
Page 31: Using The Pattern Explanation Function
LCD SCREEN Read the explanations and select the Press appropriate stitch. → The screen displays directions for sewing the selected stitch. Follow the directions to sew the stitch. Press to view the next page. Press to view the previous page. Press to return to the original screen.
Page 32: Lower Threading
LOWER THREADING LOWER THREADING ■ Using the Supplemental Spool Pin Winding the Bobbin With this machine, you can wind the bobbin without unthreading the machine. While using the main spool pin to sew, you can conveniently wind → → → Press the bobbin using the supplemental spool pin.
Page 33 LOWER THREADING Set the supplemental spool pin in the “up” Memo position. • When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the thread spool. a Spool cap (small) a Supplemental spool pin b Thread spool (cross-wound thread) Place the spool of thread on the...
Page 34 LOWER THREADING Pass the thread around the pre-tension disk Pass the end of the thread through the guide making sure that the thread is under the slit in the bobbin winder seat, and pull the pre-tension disk. thread to the right to cut the thread with the cutter.
Page 35: Using The Spool Pin
LOWER THREADING Press Cut the thread with scissors and remove the bobbin. → Bobbin winding starts automatically. The bobbin stops rotating when bobbin winding is completed. The bobbin winding switch will automatically return to its original position. Note • changes to while the bobbin Memo is winding.
Page 36: Untangling Thread From Beneath The Bobbin Winder Seat
LOWER THREADING Turn the main power to ON and open the Pass the thread through the thread guide. top cover. Align the groove in the bobbin with the spring on the bobbin winder shaft, and set the bobbin on the shaft. a Thread guide Pass the thread around the pre-tension disk making sure that the thread is under the...
Page 37: Setting The Bobbin
LOWER THREADING If the thread becomes tangled under the Setting the Bobbin bobbin winder seat, press once to stop the bobbin winding. → → → Press → in this order to display a video example of the operation on the LCD (see page B-29).
Page 38 LOWER THREADING Slide the bobbin cover latch to the right. While lightly holding down bobbin with your right hand as shown, guide the thread through the slit (a and b). At this time, check that the bobbin easily rotates counterclockwise. Then, pull the thread toward you to cut it with the cutter (c).
Page 39: Pulling Up The Bobbin Thread
LOWER THREADING Insert the tab in the lower-left corner of the Press the “Needle Position” button to raise bobbin cover (1), and then lightly press the needle. down on the right side to close the cover Press to lock all keys and buttons. (2).
Page 40: Upper Threading
UPPER THREADING UPPER THREADING Turn the main power to ON. Upper Threading Press the “Presser Foot Lifter” button to → → → Press raise the presser foot. → in this order to display a video example of the operation on the LCD (see page B-29).
Page 41 UPPER THREADING Pivot the spool pin so that it angles upward. Set the thread spool on the spool pin so that Memo • When sewing with fine, cross-wound the thread unwinds from the front of the thread, use the small spool cap, and leave a spool.
Page 42 UPPER THREADING While holding the thread in your right Press the “Presser Foot Lifter” button to hand, pass the thread through the thread lower presser foot. guide in the direction indicated. Pass the thread through the thread guide disks (marked “7”). Make sure that the thread passes through the groove in the thread guide.
Page 43 UPPER THREADING Press the “Automatic Threading” button to have the machine automatically thread the Memo • If the needle could not be threaded or the needle. thread was not passed through the needle bar thread guides, perform the procedure again starting from step Then, pass the thread through the eye of the needle after step Note...
Page 44: Using The Twin Needle Mode
UPPER THREADING Thread the machine for the first needle Using the Twin Needle Mode according to the procedure for threading a single needle (“Upper Threading” on page B-38). The twin needle can only be used for patterns that show after being selected. Before you select a stitch pattern, make sure the stitch can be sewn in the twin needle mode (refer to the “STITCH SETTING CHART”...
Page 45 UPPER THREADING Place the additional spool of thread on the Continue threading however do not pass supplemental spool pin, so that the thread the thread in the needle bar thread guide unwinds from the front. Push the spool cap “6” on the needle bar. Thread the needle on onto the spool pin as far as possible to the right side.
Page 46: Using Threads That Unwind Quickly
UPPER THREADING ■ Using the Vertical Spool Pin Start sewing. Sample of Twin Needle Sewing Use the vertical spool pin when using an irregularly shaped thread spool, and when sewing with metallic thread. Insert the vertical spool pin onto the bobbin winder shaft.
Page 47: Changing The Presser Foot
CHANGING THE PRESSER FOOT CHANGING THE PRESSER FOOT CAUTION • Always press on the screen to lock all keys and buttons before changing the presser foot. If is not pressed and the “Start/Stop” button or another button is pressed, the machine will start and may cause injury.
Page 48: Attaching The Free Motion Echo Quilting Foot "E
CHANGING THE PRESSER FOOT ■ Attaching the Free Motion Echo Attach the free motion echo quilting foot “E” on the left side of the adapter with the Quilting Foot “E” holes in the quilting foot and adapter aligned. Follow the steps in “Removing the Presser Foot”...
Page 49: Changing The Needle
CHANGING THE NEEDLE CHANGING THE NEEDLE CAUTION • Always press on the screen to lock all keys and buttons before changing the needle. If not pressed and the Start/Stop button or another operation button is pressed accidentally, the machine will start and injury may result. •...
Page 50 CHANGING THE NEEDLE With the flat side of the needle facing the back, insert the new needle all the way to the top of the needle stopper (viewing window) in the needle clamp. Use a screwdriver to securely tighten the needle clamp screw.
Page 51: About The Needle And Fabric
ABOUT THE NEEDLE AND FABRIC ABOUT THE NEEDLE AND FABRIC About the Needle The sewing machine needle is probably the most important part of the sewing machine. Choosing the proper needle for your sewing project will result in a beautiful finish and fewer problems. Below are some things to keep in mind about needles.
Page 52: Using Functions By Connecting The Accessory To The Machine
USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE Using USB Media Note • The connectors on the USB cable can only be inserted into a port in one direction. If it is difficult to insert the connector, do not insert it with force.
Page 53: Using The Dual Feed Foot
USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE ■ Clicking a Key Using the Dual Feed Foot When the mouse is connected, the pointer appears on the screen. Move the mouse to position the Dual feed foot enables you to have best fabric pointer over the desired key, and then click the left control when sewing difficult fabrics that slip mouse button.
Page 54 USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE Raise the presser foot lever. Hold the dual feed foot in place with your right hand, then using the included screwdriver securely tighten the large screw. Push the black button on the presser foot holder and remove the presser foot.
Page 55: Attaching/Detaching Toe
USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE ■ Attaching/Detaching Toe ■ Using the Dual Feed Position Lever Attach the toe by aligning the pins with the notches When the feed position lever is up, the black roller and snap it into place. belt on the dual feed is not engaged.
Page 56 USING FUNCTIONS BY CONNECTING THE ACCESSORY TO THE MACHINE to increase or decrease the feeding of the top fabric. Select “00” for sewing in most cases. If the feed amount for the top fabric is too little, causing the fabric to be longer than the bottom fabric, press to increase the feed amount for the top fabric.
Page 57 Sewing This section describes procedures for using the various utility stitches as well as other functions. It provides details on basic sewing in addition to the more expressive features of the machine, from sewing tubular pieces and buttonholes to sewing the character and decorative stitch patterns.
Page 58: S Sewing
Sewing Chapter Sewing Basics SEWING..............3 Sewing a Stitch ................3 ■ Using the Foot Controller ............4 Sewing Reinforcement Stitches ...........5 Automatic Reinforcement Stitching ...........5 Sewing Curves ................7 Changing Sewing Direction ............7 ■ Sewing a Seam Allowance of 0.5 cm or Less ......7 Sewing Heavyweight Fabrics ............7 ■...
Page 59: Sewing
SEWING SEWING CAUTION • To avoid injury, pay special attention to the needle while the machine is in operation. Keep your hands away from moving parts while the machine is in operation. • Do not stretch or pull the fabric during sewing. Doing so may lead to injury. •...
Page 60: Using The Foot Controller
SEWING Press the “Start/Stop” button to start Note sewing. • When cutting thread thicker than #30, nylon Guide the fabric lightly by hand. monofilament thread, or other decorative threads, use the thread cutter on the side of the machine. When the needle has stopped moving, raise Memo the presser foot and remove the fabric.
Page 61: Sewing Reinforcement Stitches
SEWING Insert the foot controller plug into its jack If the automatic reinforcement stitch is selected on the screen, reverse stitches (or reinforcement on the machine. stitches) will be sewn automatically at the beginning of sewing when the “Start/Stop” button is pressed.
Page 62 SEWING Press the “Reverse Stitch” button or Press to set the automatic “Reinforcement Stitch” button. reinforcement stitching function. a Reverse stitches (or reinforcement stitches) → The machine will sew reverse stitches (or reinforcement stitches) and stop. Memo • To turn off the automatic reinforcement stitching function, press again, so it appears as...
Page 63: Sewing Curves
SEWING ■ Sewing a Seam Allowance of 0.5 cm “Reverse Stitch” “Reinforcement or Less button Stitch” button Baste the corner before sewing, and then, after Machine starts Machine starts changing the sewing direction at the corner, pull the sewing and then sews sewing at the basting thread toward the back while sewing.
Page 64: Sewing Hook-And-Loop Fastener
SEWING ■ If the Fabric does not Fit under the Release the black button. Presser Foot If the presser foot is in the up position, and you are sewing heavyweight or multiple layers of fabric which do not fit easily under the presser foot, use the presser foot lever to raise the presser foot to its highest position.
Page 65: Sewing Lightweight Fabrics
SEWING Sewing Lightweight Fabrics Place thin paper or tear away embroidery stabilizer under thin fabrics to make sewing easier. Gently tear off the paper or the stabilizer after sewing. a Thin paper Sewing Stretch Fabrics First, baste together the pieces of fabric, and then sew without stretching the fabric.
Page 66: Stitch Settings
STITCH SETTINGS STITCH SETTINGS When you select a stitch, your machine automatically selects the appropriate stitch width, stitch length, “L/R SHIFT”, and upper thread tension. However, if needed, you can change any of the individual settings. Note • Settings for some stitches cannot be changed (refer to the “STITCH SETTING CHART” on page S-68). •...
Page 67: Setting The Stitch Length
STITCH SETTINGS Setting the Stitch Length Setting the “L/R SHIFT” Follow the steps below when you want to change Follow the steps below when you want to change the stitch pattern length. the placement of the zigzag stitch pattern by moving it left and right.
Page 68: Setting The Thread Tension
STITCH SETTINGS ■ Upper Thread is Too Tight Setting the Thread Tension If the bobbin thread is visible on the right side of the fabric, the upper thread is too tight. You may need to change the thread tension, depending on the fabric and thread being used. Note Follow the steps below to make any necessary •...
Page 69: Upper Thread Is Too Loose
STITCH SETTINGS ■ Upper Thread is Too Loose If the upper thread is visible from the wrong side of the fabric, the upper thread is too loose. Note • If the upper thread was incorrectly threaded, the upper thread may appear to be too loose.
Page 70: Useful Functions
USEFUL FUNCTIONS USEFUL FUNCTIONS Set the fabric in the start position and start Automatic Thread Cutting sewing. After selecting a stitch pattern, turn on the automatic thread cutting function before sewing, and the machine will automatically sew reinforcement stitches (or reverse stitches, depending on the stitch pattern) at the beginning and end of sewing, and trim the threads at the end of sewing.
Page 71: Using The Knee Lifter
USEFUL FUNCTIONS Use your knee to move the knee lifter bar to Using the Knee Lifter the right in order to raise the presser foot. Release the knee lifter to lower the presser foot. Using the knee lifter, you can raise and lower the presser foot with your knee, leaving both hands free to handle the fabric.
Page 72 USEFUL FUNCTIONS Select a stitch. Memo • When the pivot setting is selected, the Press to select the pivot setting. height of the presser foot when sewing is stopped can be changed according to the type of fabric being sewn. Press display “Pivoting Height”...
Page 73: Automatic Fabric Sensor System (Automatic Presser Foot Pressure)
USEFUL FUNCTIONS Press the “Start/Stop” button to stop the Automatic Fabric Sensor System machine at the point where the sewing direction changes. (Automatic Presser Foot Pressure) The thickness of the fabric is automatically detected and the presser foot pressure is automatically adjusted with an internal sensor while sewing, to insure that your fabric is fed smoothly.
Page 74: Needle Position - Stitch Placement
USEFUL FUNCTIONS Needle Position – Stitch Locking the Screen Placement If the screen is locked before starting to sew, the various settings such as the stitch width and stitch When the “Needle Position – Stitch Placement” is length are locked and cannot be changed. This on, the needle will be partially lowered for precise prevents screen settings from accidentally being stitch placement and then press the “Needle...
Page 75 USEFUL FUNCTIONS Sewing S-19...
Page 76: Chapter2 Utility Stitches
Sewing Chapter Utility Stitches SELECTING UTILITY STITCHES ....... 21 Darning ..................58 Bar Tacks ................. 59 Selecting a Stitch ..............21 ■ Bar Tacks on Thick Fabrics ............61 ■ Using the Mirror Image Key ............ 21 Button Sewing ................. 61 ■ Using the Image Key ..............22 ■...
Page 77: Selecting Utility Stitches
SELECTING UTILITY STITCHES SELECTING UTILITY STITCHES ■ Using the Mirror Image Key Selecting a Stitch Depending on the type of utility stitch you select, you may be able to sew a horizontal mirror image of There are 5 categories of Utility Stitches. the stitch.
Page 78: Saving Your Stitch Settings
SELECTING UTILITY STITCHES ■ Using the Image Key Saving Your Stitch Settings You can display an image of the selected stitch. You can check and change the colors of the image of the The settings for the zigzag stitch width, stitch screen.
Page 79: Retrieving Saved Settings
SELECTING UTILITY STITCHES ■ Retrieving Saved Settings Memo • To save new settings when there are Select a stitch. already 5 sets of settings saved for a stitch, press in the memory function screen. Memo Press the numbered key of the setting to be •...
Page 80: Sewing The Stitches
SEWING THE STITCHES SEWING THE STITCHES Straight Stitches Memo • Refer to “Sewing Reinforcement Stitches” on page S-5 for the detailed See page S-68 for the detailed information of information of reverse stitches and stitches. reinforcement stitches. Stitch Stitch name Presser foot Select a stitch.
Page 81: Changing The Needle Position (Left Or Middle Needle Position Stitches Only)
SEWING THE STITCHES ■ Changing the Needle Position (Left Press the “Start/Stop” button to sew forward. or Middle Needle Position Stitches Only) When you select left or middle needle position stitches, you can use in the stitch width display to change the position of the needle. Match the distance from the right edge of the presser foot to the needle with the stitch width, then align the edge of the presser foot with the edge of the...
Page 82: Aligning The Fabric With A Mark On The Needle Plate Or Bobbin Cover (With Mark)
SEWING THE STITCHES ■ Aligning the Fabric with a Mark on ■ Using the Straight Stitch Needle the Needle Plate or Bobbin Cover Plate and the Straight Stitch Foot (with Mark) The straight stitch needle plate and the straight stitch foot can only be used for straight stitches (middle While sewing, align the edge of the fabric with the needle position stitches).
Page 83 SEWING THE STITCHES Grasp the bobbin case, and then pull it out. Insert the bobbin case in its original position, and then attach the needle plate cover. After reinstalling the needle plate cover, select any of the straight stitches. Memo •...
Page 84: Dart Seam
SEWING THE STITCHES ■ Basting Dart Seam Select and attach presser foot “J”. Select and attach presser foot “J”. Press the “Reverse Stitch” button to sew reinforcement stitches, then continue Sew a reverse stitch at the beginning of the sewing. dart and then sew from the wide end to the other end without stretching the fabric.
Page 85: Gathering
SEWING THE STITCHES Iron the dart to one side so that it is flat. Sew two rows of straight stitches parallel to the seam line, then trim excess thread leaving 50 mm (approx. 1-15/16 inches). a Seam line Gathering b 10 mm to 15 mm (approx. 3/8 inch to 9/16 inch) c About 50 mm (approx.
Page 86: Pintuck
SEWING THE STITCHES reinforcement stitch and trim the thread Finished flat fell seam automatically at the end of sewing. a Surface Pintuck a About 12 mm (approx. 1/2 inch) b Wrong side Mark along the folds on the wrong side of Spread the fabric out along the finish line.
Page 87: Zigzag Stitches
SEWING THE STITCHES Sew a straight stitch along the fold. Select a stitch. When the automatic thread cutting and automatic reinforcement stitching are preset, reinforcement stitches will be sewn automatically at the beginning of sewing. Press the “Reverse Stitch” button to sew a reinforcement stitch and trim the thread automatically at the end of sewing.
Page 88: Patchwork (For Crazy Quilt)
SEWING THE STITCHES ■ Patchwork (for Crazy Quilt) Snap the cord guide bobbin cover into place, making sure that the gimp thread can Turn back the desired width of fabric and position it be fed freely. over the lower fabric, then sew so that the stitch bridges both pieces of fabric.
Page 89: Elastic Zigzag Stitches
SEWING THE STITCHES ■ Overcasting Elastic Zigzag Stitches Use this stitch to sew overcasting on the edge of stretch fabrics. Sew the overcasting along the edge Use elastic zigzag stitches for tape attaching, of the fabric while positioning the right-hand side overcasting, darning, or a wide variety of other needle drop point just outside the edge of the fabric.
Page 90: Overcasting Using Presser Foot "J
SEWING THE STITCHES Select a stitch and attach presser foot “G”. CAUTION • After the stitch width is adjusted, rotate the handwheel toward you (counterclockwise). Check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may break and cause injury.
Page 91: Quilting
SEWING THE STITCHES Sew with the needle dropping slightly off Presser foot the edge of the fabric. Stitch Stitch name Stem stitch Quilting appliqué zigzag stitch Zigzag stitch (Right) a Needle drop position Zigzag stitch (Left) Note • Use the “L/R SHIFT” setting for fine tuning 2 steps elastic zigzag the placement of the stitch.
Page 92: Piecing
SEWING THE STITCHES Presser foot Note Stitch Stitch name • The width range of stitch setting is only available in the Quilting stitch “Q” quilting category. Rick-rack stitch ■ Piecing Decorative stitch Sewing two pieces of fabric together is called piecing.
Page 93: Piecing Using The 1/4" Quilting Foot With Guide (Optional With Some Models)
SEWING THE STITCHES Creating an accurate seam allowance Use the mark on the foot to begin, end, or pivot 1/4 Memo inch from edge of fabric. • Using a straight stitch (middle needle position) makes it easier to sew smoothly (see page S-24).
Page 94: Appliqué
SEWING THE STITCHES ■ Appliqué Use the quilting appliqué stitch to attach the appliqué. Sew around the edge while Trace the pattern onto the appliqué fabric dropping the needle as close to the edge as and then cut around it, leaving a 3 mm to possible.
Page 95: Quilting With Satin Stitches
SEWING THE STITCHES You can use the appliqué technique to attach Set the “Width Control” to “ON”. appliqué designs like the three pictured below. a Dresden plate b Stained glass Memo c Sunbonnet sue • You can use the speed control slide to adjust the stitch width.
Page 96: Free Motion Quilting
SEWING THE STITCHES ■ Free Motion Quilting Memo With free motion quilting, the feed dogs can be • When starting to sew, the internal sensor detects the thickness of the fabric, and the lowered by pressing , so that the fabric can be quilting foot is raised to the height specified moved freely in any direction.
Page 97 SEWING THE STITCHES Attach free motion open toe quilting foot Press to cancel the free motion sewing “O” by positioning the pin of the quilting mode. foot above the needle clamp screw and → Rotate the handwheel toward you aligning the lower-left of the quilting foot (counterclockwise) to raise the feed dogs.
Page 98 SEWING THE STITCHES Attach the straight stitch needle plate (see → The key appears as , the quilting foot is raised to page S-26). the necessary height, and then the feed dogs are lowered for free motion sewing. a Round hole Memo •...
Page 99: Echo Quilting Using The Free Motion Echo Quilting Foot "E" (Optional With Some Models)
SEWING THE STITCHES ■ Echo Quilting Using the Free Motion CAUTION Echo Quilting Foot “E” (optional with some models) • Be sure to securely tighten the screws with the Sewing quilting lines at equal distances around a included screwdriver. Otherwise, the needle motif is called echo quilting.
Page 100 SEWING THE STITCHES Attach the adapter (“CHANGING THE Memo PRESSER FOOT” of “Basic operations”). • When starting to sew, the internal sensor Attach the free motion echo quilting foot detects the thickness of the fabric, and the quilting foot is raised to the height specified “E”...
Page 101: Blind Hem Stitches
SEWING THE STITCHES Using the measurement on the quilting foot Blind Hem Stitches as a guide, sew around the motif. Secure the bottoms of skirts and pants with a blind hem. Two stitches are available for blind hem stitching. Stitch Stitch name Presser foot Blind hem stitch...
Page 102 SEWING THE STITCHES Use a chalk to mark on the fabric about 5 Select mm (3/16 inch) from the edge of the fabric, and then baste it. a Wrong side of fabric b Right side of fabric c Edge of fabric d Desired edge of hem e 5 mm (3/16 inch) f Basting...
Page 103: If The Needle Catches Too Much Of The Hem Fold
SEWING THE STITCHES ■ If the Needle Catches Too Much of Adjust the stitch width until the needle slightly catches the fold of the hem. the Hem Fold The needle is too far to the left. Press to decrease the stitch width so that the needle slightly catches the fold of the hem.
Page 104: Appliqué
SEWING THE STITCHES <Normal fabric> Attach presser foot “J”. Check that the needle drops slightly off the edge of the appliqué, then start sewing. a Wrong side of fabric b Right side of fabric Sew with the fold of the hem against the presser foot guide.
Page 105: Shelltuck Stitches
SEWING THE STITCHES ■ Appliqué Corners To make rows of shell tuck stitches, fold the fabric in half along the bias. Stop the machine with the needle in the right position of the outside (or inside) corner of the appliqué. Raise the presser foot and pivot the fabric to align the fabric edge.
Page 106: Scallop Stitches
SEWING THE STITCHES Unfold the fabric, and iron the tucks to one Trim along the seam, making sure not to cut side. the stitches. Memo Memo • To make shell tucks at the edge of a collar • Use a seam sealant to secure the edges of or neckline, follow the pattern’s instructions the scallop stitches.
Page 107: Smocking Stitches
SEWING THE STITCHES Select a stitch for top stitching. Pull the bobbin threads to obtain the desired amount of gather, and then smooth the gathers by ironing them. Place the fabric right side up in the machine, and center the presser foot over the seam when sewing.
Page 108: Fagoting
SEWING THE STITCHES Fagoting Tape or Elastic Attaching When there is a space between two fabrics with Select a straight stitch and attach presser thread sewn over the space to join the fabrics foot “J”. together, it is called fagoting. Use this stitch when sewing blouses or children’s clothes.
Page 109: Heirloom
SEWING THE STITCHES Select Heirloom ■ Hemstitching (1) Memo Use for sewing tablecloths, decorative hems, and • For details on each stitch, refer to the decorative stitching on shirt fronts. “STITCH SETTING CHART” on page S-68. Sew over the tape (or elastic). Memo •...
Page 110: Hemstitching (2) (Drawn Work (1))
SEWING THE STITCHES Start sewing. Press to create a mirror image of the stitch. Example: Illustration of finished product Match beginning needle drop points on the opposite edge of the open area to keep the stitching symmetrical. ■ Hemstitching (2) (Drawn Work (1)) Pull out several threads from one area on a piece of fabric to open the area.
Page 111: One-Step Buttonholes
SEWING THE STITCHES Sew the decorative stitch in the center of Stitch Stitch name Presser foot the five threads created above. Bound buttonhole Keyhole buttonhole Tapered keyhole buttonhole Keyhole buttonhole Memo One-step buttonholes are sewn from the front of • A wing needle can be used for Hemstitching the presser foot to the back, as shown below.
Page 112 SEWING THE STITCHES Select a buttonhole stitch, and attach buttonhole foot “A”. Note • Pass the thread underneath the presser Mark the position and length of the foot. buttonhole on the fabric. • Slide the outside frame of the buttonhole foot backward as far as possible as shown in the illustration, making sure that there is no gap behind the part of the foot marked...
Page 113: Sewing Stretch Fabrics
SEWING THE STITCHES ■ Sewing Stretch Fabrics Memo • If automatic thread cutting is turned on When sewing on stretch fabric with before you start sewing, both threads are automatically cut after the reinforcement sew the buttonhole stitches over a gimp thread. stitches are sewn.
Page 114: Darning
SEWING THE STITCHES ■ Odd Shaped Buttons/Buttons that do Darning Not Fit into the Button Holder Plate Use the markings on the presser foot scale to set the Use darning stitches for mending and other size of the buttonhole. One mark on the presser foot applications.
Page 115: Bar Tacks
SEWING THE STITCHES Check that the needle drops at the desired Gently hold the end of the upper thread, position and lower the presser foot, making and then press the “Start/Stop” button to sure the upper thread passes underneath start the machine. the buttonhole foot.
Page 116 SEWING THE STITCHES Lower the buttonhole lever so that it is Memo positioned behind the metal bracket on the • Bar tacks can be between 5 mm (approx. buttonhole foot. 3/16 inch) and 28 mm (approx. 1-1/16 inches). Bar tacks are usually between 5 mm (approx.
Page 117: Button Sewing
SEWING THE STITCHES ■ Bar Tacks on Thick Fabrics Attach button sewing foot “M”, slide the button along the metal plate and into the Place a piece of folded fabric or cardboard beside presser foot, and lower the presser foot. the fabric being sewn to level the buttonhole foot and allow for easier and even feeding.
Page 118: Eyelet
SEWING THE STITCHES ■ Attaching 4 Hole Buttons Eyelet Sew the two holes closest to you. Then raise the presser foot and move the fabric so that the needle Use this stitch for making belt holes and other goes into the next two holes, and sew them in the similar applications.
Page 119: Multi-Directional Sewing (Straight Stitch And Zigzag Stitch)
SEWING THE STITCHES Use the eyelet punch to make a hole in the Select and attach monogramming foot center of the stitching. “N”. Multi-directional Sewing Memo (Straight Stitch and Zigzag Stitch) • For details on each stitch, refer to the “STITCH SETTING CHART”...
Page 120: Zipper Insertion
SEWING THE STITCHES Attach presser foot “J” and sew straight Select and sew seam “3” as shown. stitches up to the zipper opening. Change to a basting stitch (see page S-28) and sew to the top of the fabric. → The fabric feeds forward while stitching backward. a Basting stitches Select and sew seam “4”...
Page 121: Inserting A Side Zipper
SEWING THE STITCHES Attach presser foot “J” and sew straight stitches up to the zipper opening. Change to CAUTION a basting stitch and sew to the top of the fabric. • When using zipper foot “I”, make sure the straight stitch, middle needle position is selected.
Page 122 SEWING THE STITCHES Align the right side of the pin in zipper foot “I” with the presser foot holder, and attach CAUTION the presser foot. • Make sure the needle does not strike the zipper during sewing. If the needle strikes the zipper, the needle may break, leading to injury.
Page 123 SEWING THE STITCHES Open the zipper and sew the rest of the seam. a Basting stitches b 7 mm to 10 mm (approx. 1/4 inch to 3/8 inch) c Reverse stitches d 50 mm (approx. 2 inches) Sewing S-67...
Page 124: Stitch Setting Chart
STITCH SETTING CHART STITCH SETTING CHART The following chart shows information for each utility stitch concerning applications, stitch lengths, stitch widths, and whether or not the twin needle mode can be used. Stitch width Stitch length Presser foot [mm (inch)] [mm (inch)] Twin Stitch...
Page 125 STITCH SETTING CHART Stitch width Stitch length Presser foot [mm (inch)] [mm (inch)] Twin Stitch Stitch name Applications needle Auto. Manual Auto. Manual Overcasting Reinforcing of heavyweight 2.5 - 5.0 0.4 - 5.0 stitch fabric (3/16) (3/32 - 3/16) (3/32) (1/64 - 3/16) Overcasting Reinforcing of medium,...
Page 126 STITCH SETTING CHART Stitch width Stitch length Presser foot [mm (inch)] [mm (inch)] Twin Stitch Stitch name Applications needle Auto. Manual Auto. Manual Quilting Quilting stitch for invisible 0.0 - 7.0 0.4 - 5.0 appliqué stitch appliqué or attaching binding (1/16) (0 - 1/4) (1/16)
Page 127 STITCH SETTING CHART Stitch width Stitch length Presser foot [mm (inch)] [mm (inch)] Twin Stitch Stitch name Applications needle Auto. Manual Auto. Manual Serpentine Decorative stitching and 0.0 - 7.0 0.2 - 5.0 stitch attaching elastic (3/16) (0 - 1/4) (1/16) (1/64 - 3/16) ( J )
Page 128 STITCH SETTING CHART Stitch width Stitch length Presser foot [mm (inch)] [mm (inch)] Twin Stitch Stitch name Applications needle Auto. Manual Auto. Manual Hemstitching Heirloom, decorative hems 0.0 - 7.0 0.4 - 5.0 (15/64) (0 - 1/4) (3/16) (1/64 - 3/16) ( J ) Hemstitching Heirloom, decorative hems...
Page 129 STITCH SETTING CHART Stitch width Stitch length Presser foot [mm (inch)] [mm (inch)] Twin Stitch Stitch name Applications needle Auto. Manual Auto. Manual Keyhole Buttonholes in heavyweight or 3.0 - 7.0 0.3 - 1.0 buttonhole thick fabrics for larger flat (1/4) (1/8 - 1/4) (1/32)
Page 130 STITCH SETTING CHART Stitch width Stitch length Presser foot [mm (inch)] [mm (inch)] Twin Stitch Stitch name Applications needle Auto. Manual Auto. Manual Forward For attaching appliqué on (Zigzag) tubular pieces of fabric and — — — — mitering corners Reverse For attaching appliqué...
Page 131 STITCH SETTING CHART Stitch width Stitch length Presser foot [mm (inch)] [mm (inch)] Twin Stitch Stitch name Applications needle Auto. Manual Auto. Manual Tape attaching Attaching tape to seam in 5.50 0.00 - 7.00 0.2 - 5.0 stretch fabric (7/32) (0 - 1/4) (1/16) (1/64 - 3/16)
Page 132: Chapter3 Character/Decorative Stitches
Sewing Chapter Character/Decorative Stitches SELECTING STITCH PATTERNS ....... 77 Selecting Decorative Stitch Patterns/7mm Decorative Stitch Patterns/Satin Stitch Patterns/7mm Satin Stitch Patterns/Cross Stitch/Utility Decorative Stitch Patterns ...78 Characters ................78 ■ Deleting Characters ..............79 ■ Adjusting the Character Spacing ..........80 SEWING STITCH PATTERNS ........
Page 133: Selecting Stitch Patterns
SELECTING STITCH PATTERNS SELECTING STITCH PATTERNS Press to display the screen below. There are 7 categories of Character/Decorative stitch patterns. a Decorative stitch patterns b 7mm decorative stitch patterns. You can set stitch length and width. c Satin stitch patterns d 7mm satin stitch patterns.
Page 134: Selecting Decorative Stitch Patterns/7Mm Decorative Stitch Patterns/Satin Stitch Patterns/7Mm Satin Stitch Patterns/Cross Stitch/Utility Decorative Stitch Patterns
SELECTING STITCH PATTERNS Selecting Decorative Stitch Characters Patterns/7mm Decorative Stitch Example: Entering “Blue Sky”. Patterns/Satin Stitch Patterns/7mm Satin Stitch Press Patterns/Cross Stitch/Utility Decorative Stitch Patterns Select the category of the pattern you want to sew. Press the key of the stitch pattern you want to sew.
Page 135: Deleting Characters
SELECTING STITCH PATTERNS Press and then enter “B”. Press and then enter “ky”. If you want to continue entering characters in a Press and then enter “lue”. different font, press , and then repeat from step ■ Deleting Characters Press to delete the last character.
Page 136: Adjusting The Character Spacing
SELECTING STITCH PATTERNS ■ Adjusting the Character Spacing Press to adjust character spacing. The space between the characters can be adjusted. Press Press to display on the screen. Press to increase the character spacing and press to decrease the character spacing. Example: →...
Page 137: Sewing Stitch Patterns
SEWING STITCH PATTERNS SEWING STITCH PATTERNS Sewing Attractive Finishes To achieve attractive results when sewing character/decorative stitches, check the table below for the proper fabric/thread/needle combinations. Note • Other factors, such as fabric thickness, stabilizer material, etc., also have an effect on the stitch, so you should always sew a few trial stitches before beginning your project.
Page 138: Making Adjustments
SEWING STITCH PATTERNS Memo Note • If the fabric is pulled or pushed during • When sewing some patterns, the needle will sewing, the pattern may not turn out temporarily pause in the raised position correctly. Also, depending on the pattern, while the fabric is fed due to the operation there may be movement to the left and right of the needle bar separation mechanism...
Page 139 SEWING STITCH PATTERNS Attach monogramming foot “N” and sew If the pattern is bunched: the pattern. Press in the “Fine Adjust Verti.” display. → The displayed value increases each time the button is pressed and the pattern will lengthen. If the pattern has gaps: Press in the “Fine Adjust Verti.”...
Page 140: Editing Stitch Patterns
EDITING STITCH PATTERNS EDITING STITCH PATTERNS ■ Key Functions You can create just the finish you want using the editing functions. Make patterns larger or smaller, make mirror images, etc. Note • Some editing functions cannot be used with certain stitch patterns. Only the functions for the displayed keys are available when a pattern is selected.
Page 141 EDITING STITCH PATTERNS Display Key Name Explanation Page Pattern display size Show the approximate size of the pattern selected. S-21 : Nearly the same size as the sewn pattern : 1/2 the size of the sewn pattern : 1/4 the size of the sewn pattern * The actual size of the sewn pattern may differ depending on the type of fabric and thread that is used.
Page 142: Changing The Size
EDITING STITCH PATTERNS Display Key Name Explanation Page “L/R SHIFT” key S-11 Press to shift the stitch pattern to the right or press to shift the pattern to the left. This feature is not available on all patterns. Only those applicable will be shifted.
Page 143: Changing The Length (For 7Mm Satin Stitch Patterns Only)
EDITING STITCH PATTERNS Changing the Length (for 7mm Creating a Horizontal Mirror Satin Stitch Patterns Only) Image When 7mm satin stitch patterns are selected, press To create a horizontal mirror image, select a stitch to choose from 5 automatic length settings, pattern then press without changing the stitch zigzag width or stitch length settings.
Page 144: Changing Thread Density (For Satin Stitch Patterns Only)
EDITING STITCH PATTERNS Changing Thread Density Returning to the Beginning of the (for Satin Stitch Patterns Only) Pattern When sewing character/decorative stitches, you After selecting a satin stitch pattern, press can return to the beginning of the pattern after trial select your preferred thread density.
Page 145: Checking The Image
EDITING STITCH PATTERNS to view any part of Checking the Image the image that extends out of the viewable display area. You can display an approximate size image of the selected stitch pattern. You can also check and change the colors of the image on the screen. Press →...
Page 146: Combining Stitch Patterns
COMBINING STITCH PATTERNS COMBINING STITCH PATTERNS You can combine many varieties of stitch patterns, such as character stitches, cross stitches or satin stitches. You can also combine stitch patterns of different sizes, mirror image stitch patterns, and others. Before Combining Single stitch sewing is automatically selected for sewing combined patterns.
Page 147: Combining Large And Small Stitch Patterns
COMBINING STITCH PATTERNS Select Press → The large size stitch will be selected. Press again, then press to select the small size. Press to sew the pattern continuously. Press → The pattern is displayed in a smaller size. Press to sew continuously. Memo •...
Page 148: Combining Horizontal Mirror Image Stitch Patterns
COMBINING STITCH PATTERNS Combining Horizontal Mirror Combining Stitch Patterns of Image Stitch Patterns Different Length Example: Example: Press , then press once. Press → The length of the image is set to Press again, then press Select again, then press 3 times.
Page 149: Making Step Stitch Patterns (For 7Mm Satin Stitch Patterns Only)
COMBINING STITCH PATTERNS Example: Press Press Press → The entered pattern is repeated. Making Step Stitch Patterns (for 7mm Satin Stitch Patterns Only) You can use the keys with 7mm satin → The next stitch pattern will move to the right. stitch patterns to create a step effect.
Page 150: More Examples
COMBINING STITCH PATTERNS Press → → → Press → → → → → Press → The entered pattern is repeated. → → → ■ More Examples → → → → Press → → → → → Press → → → S-94...
Page 151: Using The Memory Function
USING THE MEMORY FUNCTION USING THE MEMORY FUNCTION Stitch Data Precautions Observe the following precautions when using stitch data other than that created and saved in this machine. ■ Types of Stitch Data that can be Used • In the Character/Decorative Stitch memory, “.pmv”, “.pmx” and “.pmu” stitch data files can be used with this machine.
Page 152: Saving Stitch Patterns In The Machine's Memory
USING THE MEMORY FUNCTION ■ If the Memory is Full Saving Stitch Patterns in the If the following screen appears while you are trying Machine’s Memory to save a pattern on the machine’s memory, the memory is too full to hold the currently selected stitch pattern.
Page 153: Saving Stitch Patterns To Usb Media
USING THE MEMORY FUNCTION Press Saving Stitch Patterns to USB Media When sending stitch patterns from the machine to USB media, plug the USB media into the machine’s top USB port. Memo • USB media is commercially available, but some USB media may not be usable with this machine.
Page 154: Saving Stitch Patterns In The Computer
USING THE MEMORY FUNCTION Insert the USB media into the USB port on Saving Stitch Patterns in the the machine. Computer Using the included USB cable, the machine can be connected to your computer, and the stitch patterns can be temporarily retrieved from and saved in the “Removable Disk”...
Page 155: Retrieving Stitch Patterns From The Machine's Memory
USING THE MEMORY FUNCTION Press Retrieving Stitch Patterns from the Machine’s Memory Press → The pocket selection screen appears. Choose a stitch pattern to retrieve. Press If the entire saved stitch pattern is not displayed, press the thumbnail. Press to return to the original screen without Press to return to the original screen without saving.
Page 156: Recalling From Usb Media
USING THE MEMORY FUNCTION Press when there is a subfolder to Recalling from USB Media sort two or more stitch patterns to USB media, the stitch pattern in the subfolder is You can recall a specific stitch pattern from either displayed.
Page 157: Recalling From The Computer
USING THE MEMORY FUNCTION Move/copy the pattern data to “Removable Press Disk”. Press to delete the stitch pattern. The pattern will be deleted from the USB media. → Stitch pattern data in “Removable Disk” is written to the machine. Note •...
Page 158 USING THE MEMORY FUNCTION Press Press to delete the stitch pattern. The pattern will be deleted from the “Removable Disk” folder in your computer. → The selected stitch pattern is recalled and the sewing screen will be displayed. Note • The pattern recalled from the computer is only temporarily written to the machine.
Page 159 USING THE MEMORY FUNCTION Sewing S-103...
Page 160: Chapter4 How To Create Bobbin Work (Sewing)
Sewing Chapter How to Create Bobbin Work (Sewing) ABOUT BOBBIN WORK........105 PREPARING FOR BOBBIN WORK......105 Required Materials..............105 ■ Bobbin case and bobbin cover ..........105 ■ Lower thread................106 ■ Upper thread ................. 106 ■ Needle ................... 106 ■...
Page 161: About Bobbin Work
ABOUT BOBBIN WORK ABOUT BOBBIN WORK Beautiful embroidery work, with a three-dimensional appearance, can be created by winding the bobbin with medium to heavy weight thread or ribbon, which is too thick to be threaded through the machine’s needle. The decorative thread or ribbon will stitch out on the underneath side of fabric while sewing with the fabric wrong side facing up.
Page 162: Upper Threading
PREPARING FOR BOBBIN WORK ■ Lower thread ■ Presser foot We recommend the following types of threads for Utility stitches or decorative stitches: bobbin work. Monogramming foot “N” No.5 or finer hand embroidery thread or decorative thread Free motion sewing: Free motion open toe quilting foot “O”...
Page 163: Preparing The Bobbin Thread
PREPARING FOR BOBBIN WORK Wipe the bobbin case (gray) with a soft lint Preparing the Bobbin Thread free cloth to clean it. Insert the bobbin case so that the mark In order to create bobbin work, the bobbin case on the bobbin case aligns with the ● mark must be replaced with the one for bobbin work.
Page 164 PREPARING FOR BOBBIN WORK Install the needle plate cover. CAUTION For details on installing the needle plate cover, refer to “Cleaning the Race” of “Appendix”. • Use a bobbin thread that has been correctly wound. Otherwise, the needle may break or the thread tension will be incorrect.
Page 165: When Tension Is Applied To The Bobbin Thread
PREPARING FOR BOBBIN WORK Memo CAUTION • If inserting thread tail through bobbin hole is difficult, bobbin can be wound by holding • When winding the bobbin, make sure the the tail and wrapping thread around inside thread is not frayed. Sewing with frayed base.
Page 166: When Tension Is Not Applied To The Bobbin Thread
PREPARING FOR BOBBIN WORK ■ When tension is not applied to the Insert tweezers through bobbin thread loop and pull bobbin thread above the needle bobbin thread plate. If the bobbin thread in the trial stitching is too tight and adjusting the bobbin case tension does not help, Align the upper thread and bobbin thread, do not pass the thread through the tension spring.
Page 167: Creating Bobbin Work
CREATING BOBBIN WORK CREATING BOBBIN WORK Increase the upper thread tension. Upper Positioning the Fabric and Sewing thread tension setting between 6 and 8 is recommended for bobbin work. For details on adjusting the upper thread tension, Note refer to “Setting the Thread Tension” on •...
Page 168 CREATING BOBBIN WORK Use the presser foot lever to raise the presser foot. Note • If the bobbin thread does not come up, hold With the wrong side facing up, place the the upper thread as shown below to pull up the bobbin thread.
Page 169: Bobbin Work Free Motion Sewing
CREATING BOBBIN WORK When you have reached the end of the stitching area, stop the machine. Note • If it is difficult to place bobbin thread through the eye of a hand sewing needle, Note use a ribbon embroidery needle to pull the •...
Page 170: Adjusting The Thread Tension
ADJUSTING THE THREAD TENSION ADJUSTING THE THREAD TENSION After sewing trial stitches and checking the sewing results, adjust the thread tensions if necessary. After adjusting the tensions, be sure to sew trial stitches again in order to check the sewing results. ■...
Page 171: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING Several solutions for minor problems are described below. If the problem persists, contact your nearest authorized Baby Lock retailer. ■ The thread was activated and the Apply slight tension on bobbin thread by holding thread out to the left side of presser bobbin thread is caught inside the foot.
Page 172 TROUBLESHOOTING S-116...
Page 173: Appendix
Appendix This section provides important information for operating this machine. Please read this section to find troubleshooting tips and pointers as well as how to keep your machine in the best working order. Page number starts with “A” in this section. The screen display and machine illustration may vary slightly, depending on the country or region.
Page 174: Cleaning The Lcd Screen
Appendix Chapter Maintenance and Troubleshooting CARE AND MAINTENANCE ........3 Restrictions on oiling ..............3 Precautions on storing the machine ..........3 Cleaning the LCD Screen ............3 Cleaning the Machine Casing .............3 Cleaning the Race ...............3 Cleaning the Cutter in the Bobbin Case Area......5 About the Maintenance Message ..........5 ADJUSTING THE SCREEN .........
Page 175: Care And Maintenance
CARE AND MAINTENANCE CARE AND MAINTENANCE CAUTION • Be sure to unplug the machine before cleaning it. Otherwise, electric shock or injury may result. Restrictions on oiling Cleaning the Machine Casing In order to prevent damaging this machine, it must If the surface of the machine is dirty, lightly soak a not be oiled by the user.
Page 176 CARE AND MAINTENANCE Use the cleaning brush or a vacuum cleaner Make sure that the indicated points are aligned before installing the bobbin case. to remove any lint and dust from the race and bobbin thread sensor and the CAUTION surrounding area.
Page 177: Cleaning The Cutter In The Bobbin Case Area
CARE AND MAINTENANCE Use the screwdriver included with the Cleaning the Cutter in the Bobbin machine to screw and attach the needle plate. Case Area The cutter below the needle plate should be cleaned. If dust or lint accumulate on the cutter, it will be difficult to cut the thread when the “Thread Cutter”...
Page 178: Adjusting The Screen
ADJUSTING THE SCREEN ADJUSTING THE SCREEN Adjusting the Brightness of the Touch Panel is Malfunctioning Screen Display If the screen does not respond correctly when you touch a key (the machine does not perform the Under certain lighting conditions, the brightness of operation or performs a different operation), follow the LCD screen may need to be adjusted.
Page 179: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING If the machine stops operating correctly, check the following possible problems before requesting service. You can solve most problems by yourself. Visit us at “ www.babylock.com ”. If the problem persists, contact your nearest authorized retailer. Frequent troubleshooting topics Detailed causes and remedies for common troubleshooting topics are described below.
Page 180: Tangled Thread On Wrong Side Of Fabric
TROUBLESHOOTING While holding the bobbin in place with Tangled thread on wrong side of your finger, pass the thread through the slit in the needle plate. fabric Hold down the bobbin with your right hand, and then pull the end of the thread around the tab with ■...
Page 181 TROUBLESHOOTING Raise the presser foot using the presser foot While holding the thread in your right lever. hand, pass the thread through the thread guide in the direction indicated. If the presser foot is not raised, the sewing machine cannot be threaded correctly. Guide the thread down, up, then down Raise the needle by turning the handwheel through the groove, as shown in the...
Page 182: Incorrect Thread Tension
TROUBLESHOOTING Incorrect thread tension ■ Symptoms • Symptom 1: The lower thread is visible from the upper side of the fabric. • Symptom 2: The upper thread appears as a straight line on the upper side of the fabric. • Symptom 3: The upper thread is visible from the lower side of the fabric. •...
Page 183: Fabric Is Caught In The Machine And Cannot Be Removed
TROUBLESHOOTING Remove the bobbin case. Fabric is caught in the machine If threads remain in the bobbin case, remove them. and cannot be removed If the fabric is caught in the sewing machine and cannot be removed, the thread may have become tangled under the needle plate.
Page 184 TROUBLESHOOTING Slightly lift up the needle plate, cut any Insert the bobbin case so that the mark on the bobbin case aligns with the ● mark tangled threads, and then remove the needle plate. on the machine. Remove the fabric and threads from the needle plate. If the fabric cannot be removed, even after completing these steps, contact your nearest authorized retailer.
Page 185: Checking Machine Operations
TROUBLESHOOTING Insert the tabs on the needle plate cover Slowly turn the handwheel toward you into the needle plate, and then slide the (counterclockwise), and look from all sides cover back on. to check that the needle falls at the center of the hole in the needle plate.
Page 186: List Of Symptoms
TROUBLESHOOTING List of Symptoms Problem Cause Solution Page The thread is tangled Upper threading is incorrect. Check the steps for threading the machine B-38 on the wrong side of and rethread the machine. the fabric. Using improper needle or thread for the Check the “Fabric/Thread/Needle B-49 selected fabric.
Page 187 TROUBLESHOOTING Problem Cause Solution Page Skipped stitches Needle is turned, bent or the point is dull. Replace the needle. B-47 Using improper needle or thread for the Check the “Fabric/Thread/Needle B-49 selected fabric. Combination” chart. Machine is threaded incorrectly. Check the steps for threading the machine B-38 and rethread it correctly.
Page 188 TROUBLESHOOTING Problem Cause Solution Page High-pitched sound Dust or lint is caught in the feed dogs. Remove the dust or lint. while sewing Pieces of thread are caught in the race. Clean the race. Upper threading is incorrect. Check the steps for threading the machine B-38 and rethread the machine.
Page 189: Error Messages
ERROR MESSAGES ERROR MESSAGES If the machine is not properly set and the “Start/Stop” button or the “Reverse Stitch” button is pressed, or if the operation procedure is incorrect, the machine does not start. An alarm sounds and an error message is displayed on the LCD.
Page 190 ERROR MESSAGES Marks Error Messages Cause/Solution The bobbin thread is almost empty. This message is displayed when the bobbin thread is running out. The bobbin winder safety device has activated. Is the thread This message is displayed when the bobbin is being wound, tangled? and the motor locks because the thread is tangled, etc.
Page 191: Specifications
SPECIFICATIONS Marks Error Messages Cause/Solution When the speed controller is set to control the zigzag stitch This message is displayed when the speed control lever is set width, the "Start/Stop" button does not operate. to control the zigzag stitch width, and the “Start/Stop” button is pushed.
Page 192: Upgrading Your Machine'ssoftware
UPGRADING YOUR MACHINE’S SOFTWARE UPGRADING YOUR MACHINE’S SOFTWARE You can use USB media or a computer to upgrade software for your sewing machine. When an upgrade program is available on “ www.babylock.com ”, please download the files following the instructions on the website and steps below. Note •...
Page 193: Upgrade Procedure Using Computer
UPGRADING YOUR MACHINE’S SOFTWARE Upgrade Procedure Using Computer Note • Do not connect any additional USB media devices to your computer when using the USB cable. When the message disappears, press While pressing the “Automatic Threading” button, turn the main power to ON. →...
Page 194: Index
INDEX INDEX Accessories Eco mode ................. B-24 included accessories ............B-10 Editing options ................. B-12 character/decorative stitches ..........S-84 Accessory compartment ............B-10 Elastic zigzag stitches ............... S-33 Adapter ..................B-46 Elongation key ................S-87 Air vent ..................B-8 Error messages ................A-17 Alphabet characters Eyelet ..................
Page 195: Upper Threading
INDEX Screen brightness ............... A-6 Settings Needle automatic reinforcement stitching ........... S-5 changing the needle ............. B-47 automatic thread cutting ............S-14 changing the needle position ..........S-25 display language ..............B-25 fabric/thread/needle combinations ........B-49 machine setting mode key ............ B-21 mode ..................
Page 196 INDEX Walking foot ................B-45 Zigzag stitches ................S-31 Zipper insertion centered ................S-64 side ..................S-65 A-24...
Page 200 English 882-D11 Printed in Taiwan XF6507-001...

Baby Lock Aria BLAR Instruction And Reference Manual

Table of Contents

Chapter1 Getting Ready

Bbasic Operations 1

S Sewing 1

S Sewing 2

Chapter2 Utility Stitches

S Sewing 3

Chapter3 Character/Decorative Stitches

S Sewing 4

Chapter4 How To Create Bobbin Work (Sewing)

Appendix

A Appendix 1

Quick Links

Chapters

Troubleshooting

Related Manuals for Baby Lock Aria BLAR

Summary of Contents for Baby Lock Aria BLAR