Page 4
• Maintain a minimum distance of three inches 3 in. 3 in. 3 in. around your set-top for DC758D sufficient ventilation. See also item 7 in the Important Safety Instructions. DC758D OPERATOR’S MANUAL (501-3333200)
Page 5
The model number, serial You must not connect any other number, and electrical equipment, such as a VCR, to this rating of this set-top are input. on a label on its base. DC758D OPERATOR’S MANUAL (501-3333200)
Connect to compatible optional equipment that supports a USB 2.0 interface (future use) (Universal Serial Bus) port ETHERNET For future use. TV PASS MODULE Connect a TV Pass module, if required. ® POWER INPUT Connect your set-top’s power cord here. Make this connection last of all. DC758D OPERATOR’S MANUAL (501-3333200)
AUDIO OUT must be 75 ohm The HDMI output is then disabled, so no picture is transmitted from this connector. In that case, use the coaxial cable, not regular audio component video connectors to connect up (see Setup B). cable. DC758D OPERATOR’S MANUAL (501-3333200)
Do not, therefore, use a path through a VCR to watch your set-top programs. type of plug in the region where Use the HDMI path or an alternate direct video path from your set-top to your TV. Remember to select the you live. correct input on your TV. DC758D OPERATOR’S MANUAL (501-3333200)
Page 9
Do not, therefore, use a path through a VCR to watch your set-top programs. Use the component video path type of plug in the region where or an alternate direct video path from your set-top to your TV. Remember to select the correct input on your you live. DC758D OPERATOR’S MANUAL (501-3333200)
Do not connect your set-top (or any other equipment such as a TV or VCR) to the power supply until you have properly connected all the other cables. The power cords you use may be fitted with polarized plugs. Do not defeat the safety purpose of these polarized plugs. DC758D OPERATOR’S MANUAL (501-3333200)
Consult the information supplied by your cable service-provider for details on how to make the most of the cable, if it is disconnected from the digital cable services. Also read the operating instructions that are supplied with your remote control. AC power supply. DC758D OPERATOR’S MANUAL (501-3333200)
Each button-press changes your set-top’s output resolution, which also appears on the TV screen. Auto Pillarbox Closed Captions After a few seconds, you should see the PACE USER SETTINGS menu. Front Panel Settings Hard Disk Sleep Mode 3. Press the POWER button to remove this menu and return to normal viewing.
• rewind through a program you have been watching; • record high definition digital pictures (as well as the regular standard definition); • record one program while watching another; • record two programs while watching a previously recorded program; • schedule your set-top to record a program or a whole series; • fully manage your stored recordings; • back up your digital recordings to a VCR or DVD recorder; • retain full control over any parental viewing restrictions you have set up. You control the DVR functions using your remote control; consult the information supplied by your cable service-provider for more details. Also read the operating instructions that are supplied with your remote control. DC758D OPERATOR’S MANUAL (501-3333200)
4:3 picture in it. Dark bars are added at the sides of the Note: The effect that this button has on transmissions depends on the transmission itself. On some transmissions it may have no effect at all. transmission. DC758D OPERATOR’S MANUAL (501-3333200)
“oFF” (indicating that subtitles are currently set to be off) or “on” (indicating that subtitles are currently set Subtitles : Off to be on) appears on the front-panel display and the PACE SUBTITLE SETTINGS menu appears on the TV Subtitle Language : English screen (see right).
“ASPt” (or another of the 8 “words” shown right) should then appear on the front-panel display. If it does Front Panel Settings not appear, press the MENU button again. You should see the PACE USER SETTINGS menu on your TV Hard Disk Sleep Mode screen.
The aspect ratio is 16:9 transmitted in a 16:9 aspect ratio (see right). while the HDMI cable is disconnected from your set-top, then reconnect your HDTV via the HDMI cable. DC758D OPERATOR’S MANUAL (501-3333200)
Page 18
If you have not already done so, put your set-top into User Settings mode, as described on page 16. 1. Press the U or D button until the front panel shows “reS” (short for resolution). On the PACE USER SETTINGS menu, TV Display Capability is highlighted when “reS” is on the front panel.
SELECT button to restore the menu. 4. When you are satisfied that all the TV resolutions are correct, press the L button. The front panel shows “reS” again and the PACE USER SETTINGS menu reappears. To continue making the settings, see the next section.
3. If you want to change the setting, press U or D. Press the SELECT button to confirm the choice and change to the new setting. >NO 4. Press the L button. The front panel shows “PiLL” again and the PACE USER SETTINGS menu reappears. To continue making the settings, see the next section. > shows current setting, as does...
: Service 1 button to highlight “Reset to Defaults” on the menu, then press SELECT. Reset to Defaults 4. When you have made all the changes you want, press L twice to redisplay the PACE USER SETTINGS Closed Caption Example menu.
4. Press the L button. The front panel shows “Hdd” again. lighted MESSAGE light 5. When you have made all the changes you want, press L to redisplay the PACE USER SETTINGS menu. Making HDMI Settings You can use the HDMI Settings menu to choose an Audio Output Mode, and to enable or disable automatic detection of a newly connected HDTV (if it is connected by an HDMI cable).
3. To confirm and restore the factory settings, press the SELECT button. The factory settings are restored, and the PACE USER SETTINGS menu reappears. 4. If you want to continue changing the settings, see the sections from page 16 onwards. If you have finished changing the settings, press the POWER button.
This allows you to adjust how the picture displays on your TV screen. position Other items and options may be available on these screens. The menus may be subject to change in the future, as your set-top advances with new technology. DC758D OPERATOR’S MANUAL (501-3333200)
If the TV Aspect Ratio and TV Display Capability settings are correct, try using Zoom to improve the picture (see page 14) or consult the instructions that came with your TV and try adjusting your TV’s display. See the next page DC758D OPERATOR’S MANUAL (501-3333200)
Page 26
— (analog) channels but not (check if the BYPASS light on your set-top’s any digital channels? front panel is lighted). If Bypass is on, use the on-screen Setup menus to turn it off (see page 24). DC758D OPERATOR’S MANUAL (501-3333200)
2. Pace reserves all rights not expressly granted to you under these Terms. 3. You may not transfer any of your limited rights in the Software without the prior written consent of Pace, and if consent is provided then the Software shall only be transferred in conjunction with the transfer of the Product AND ONLY IF the transferee has read and agreed to accept these Terms.
F. General These Terms are governed by the laws of the State of New York and you may only bring claims exclusively in New York courts and Pace shall be entitled to bring a claim in the courts of any jurisdiction. Any failure by Pace to enforce any of its rights hereunder or applicable law shall not constitute a waiver of such rights. Pace’s licensors and suppliers shall be third party beneficiaries of this License Agreement, as applicable.
Page 29
Pace and are trademarks and/or registered trademarks of Pace plc. 501-3333200...