Temperature Settings; Installer Setup - Trane XT302C Installer's Manual

XT302C DELUXE PROGRAMMABLE HEAT-COOL THERMOSTAT

Temperature Settings

Refer to Table 2 for the default program. For 7-Day and
24-Hour Operation, the settings are the same for each day of
the week. Refer to the Owners Guide, Pub. No. 22-5127-04,
for instructions on changing the default settings.
Table 2. Default Program Settings.
Period Time Setpoint
Wake 6:00 AM 70 F
(21 C)
Leave 8:00 AM 62 F
(16.5 C)
Return 5:00 PM 70 F
(21 C)
Sleep 10:00 PM 62 F
(16.5 C)
The Leave, Return and Sleep periods may be cleared. For
example, the daytime energy-savings period (from Leave to
Return) may not be used by the homeowner. To clear any
period, follow the instructions in the Owners Guide in the
Clearing Schedule Period section.
Comfort-R™ OFF
CONTROL
Adaptive ON
Intelligent
Recovery™
CONTROL
(A HONEYWELL
TRADEMARK)
COOLING ON
DROOP
TEMPERATURE
FARENHEIT ( F)
DISPLAY
24-HOUR
CLOCK
CLOCK FORMAT
FORMAT
SYSTEM
AUTO/MANUAL
SETTING
(SYSTEM
(HEATING
AUTOMATICALLY
AND
SELECTS
COOLING
HEAT OR COOL;
SETTING)
YOU CAN
SELECT HEAT,
COOL OR OFF.)
OUTDOOR NO OUTDOOR
TEMPERATURE
TEMPERATURE
DISPLAY
IS DISPLAYED
PROGRAMMING
7-DAY
PROGRAMMING
M17110
Figure 9. Customizing Your Thermostat chart,
from Owners Guide, Pub. No. 22-5127-04.
Pub. No. 18-HD25D7-5
69-1213—1 (T8624)
Heat Cool Fan
Setpoint Setting
78 F Auto
(25.5 C)
85 F Auto
(29.5 C)
78 F Auto
(25.5 C)
82 F Auto
(28 C)
ON
OFF
(CONVENTIONAL
RECOVERY)
OFF
CENTIGRADE ( C)
24-HOUR
CLOCK FORMAT
MANUAL ONLY
AUTO ONLY
(YOU SELECT
(SYSTEM
HEAT, COOL AUTOMATICALLY
OR OFF.) SELECTS HEAT
OR COOL)
NO OUTDOOR
TEMPERATURE
IS DISPLAYED
CONSTANT
24-HOUR
TEMPERATURE
PROGRAMMING
SETPOINT
PROGRAMMING

INSTALLER SETUP

The Installer Setup is used to customize the thermostat for
specific systems. Some of the options include Comfort-R™
control activation, Fahrenheit vs. Centigrade temperature
display, outdoor temperature display (requires outdoor
sensor installation), and system changeover. Installer Setup
numbers are listed in Table 3. The table includes all the
configuration options and the factory-settings for the
XT302C Deluxe Programmable Multistage Thermostat .
NOTE: For most applications, the thermostat factory-
settings apply. Review the factory settings in Table 2
and if no changes are necessary, go to the Installer
Self-Test section.
IMPORTANT
The chart Customizing Your Thermostat found in the
beginning of the Owners Guide (see Fig. 9) must be
completed. The homeowner identifies the options
you install by referring to this chart.
Installer Setup Procedure
1. Press and hold the Information
and Decrease keys at the same time until all display
segments and the first setup number displays
(all display segments appear for approximately three
seconds before the setup number displays). See
Figs. 11 and 12.
Set Program Start Time
Hold for
Em Ht
Aux Ht
Mon
TueWedThuFriSatSun
Wake LeaveReturnSleep
System
Off Cool Auto
Em Heat
Fig. 10. Display of all the segments of the LCD.
INSTALLER SETUP
NUMBER DISPLAY
(COLUMN 2 OF TABLE 3)
Fig. 11. Display of Installer Setup number and option.
4
, Increase
Temporary Setting Enrg
Set Day/Time
Sav
AM
Room
PM
Heat Cool Outdoor
Recovery
In Auto Repl Batt
Fan
DST
Wait On Auto
FACTORY SETTING OR OTHER
CHOICE DISPLAY (COLUMN 3
OR 5 OF TABLE 3)
M10349
,
M17111