Advertisement
Quick Links
Advertisement
Related Manuals for Avaya P114T
Summary of Contents for Avaya P114T
- Page 1 Avaya Installation Guide Avaya P114T TACKABLE ORKGROUP WITCH...
-
Page 3: Safety Precautions
SICHERHEITSVORKEHRUNG ACHTUNG – ZUR VERHINDERUNG DES RISIKOS VON ELEKTRISCHEM SCHLAG UND FEUER 1. Die Geräte enthalten keine Bauteile, die außerhalb des Avaya Servicezentrums gewartet oder repariert werden können. Die Wartung darf NUR von qualifiziertem, technischem Personal durchgeführt werden. - Page 4 Aufschrift befindet sich neben der Stromzufuhr wo sich auch der Sicherungskasten befindet. 5. Bedienen Sie das Gerät NICHT an einer Stelle an der die Umgebungstemperatur 50ºC übersteigt. 6. Ziehen Sie das Netzkabel raus, BEVOR Sie versuchen die Hauptsicherung zu kontrollieren oder auszutauschen. P114T Stackable Switch Installation Guide...
- Page 5 100 Mbps ports can be used for server connections, high performance workstations, or to link to another P114T or P113T unit. The P114T can operate standalone or as part of a stack. A stack requires a P110 NMA to link the switches. The units are physically linked using the P110 Exoplane, which makes up a multi-gigabit, non-blocking backplane.
- Page 6 Chapter 1 Description P114T Stackable Switch Installation Guide...
-
Page 7: Installation
The drawing below shows the default positions of the DIP switches on the rear panel of the P110 hub. Figure 1 The P114T Stackable Switch Rear Panel Showing The DIP Switches In their Default Positions The DIP switches control the eight 100 Mbps ports. The ports can also be controlled by CajunView, MSNM, or any SNMP network management application via the P110 NMA. - Page 8 Chapter 2 Installation Table 1 DIP Switches on the P114T Stackable Switch Switch Function OFF (Default) (First three left- Not used most switches) USE SW Selection of operational Use management Ignore management (Use Switches) mode: control by settings. settings. management station or DIP Ignore switches.
- Page 9 Port settings can be changed using the DIP switches Stacking Operation To make the P114T work as part of a stack (and to give SNMP management capabilities to a single P114T), a P110 NMA with the correct with software version (or higher) is required.
- Page 10 Once you have downloaded the new software, set the port to disabled again and then reconnect the cable. 6. Place the P114T and any other additional P110 hubs at the bottom of the stack. 7. Connect P110 hubs using the supplied P110 Exoplane cables, as shown in Figure 2.
- Page 11 8. Connect the fiber-optic cables to the front panel ports. If the P110 NMA in the stack contains the correct software version (as specified in the P114T Stackable Switch Release Note) or higher, the stack is now fully operational. When a new version of the P110 NMA software becomes available, you should perform software download to benefit from the extra capabilities provided.
-
Page 12: Rack Mounting
4. Connect the Exoplane cables, as described above, and as illustrated in Figure 2. 5. Snap closed the hinged ends of the front panel. Figure 3 P110 rack mounting arrangement P114T Stackable Switch Installation Guide... - Page 13 Chapter 2 Installation Diagnostics Table 2 and Table 3 explain the meaning of the P114T Stackable Switch diagnostic LED indicators. Figure 4 The P114T Stackable Switch Front Panel LEDs and Buttons Table 2 Meaning of the P114T Stackable Switch Front Panel Buttons...
- Page 14 Chapter 2 Installation Table 3 Meaning of the P114T Stackable Switch front panel LEDs LED Indicator Function Status Meaning Power Mains power not connected Mains power connected Blink Working on back-up power supply Agent No agent in hub Hub contains an active agent...
- Page 15 Chapter 2 Installation P114T Stackable Switch Installation Guide...
- Page 16 © 2003 Avaya Inc. All rights reserved. All trademarks identified by the ® or TM are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks are the property of their respective owners. Document number: 130005 Rev. 0. November 2003...