Warning Displays - FujiFilm FinePix Z1 Owner's Manual

Warning Displays

Warning Displayed Explanation
An attempt was made to show 5,000 or
TOO MANY FRAMES
more images by date sorting.
i A protected file was encountered.
PROTECTED FRAME
i An attempt was made to add a voice
memo to protected file.
i The voice memo file is faulty.
t ERROR
i Camera fault.
An attempt was made to trim a 0.3M
` CAN NOT TRIM
image.
i An attempt was made to trim an image
shot using a camera other than FinePix
CAN NOT TRIM
Z1.
i The image is damaged.
Prints were specified for 1000 or more
frames in the DPOF frame settings.
DPOF FILE ERROR
An attempt was made to specify DPOF
CAN NOT SET DPOF settings for an image that is not supported
by DPOF.
The camera is not connected to a PC or
COMMUNICATION
printer.
ERROR
Displayed for PictBridge.
PRINTER ERROR
Displayed for PictBridge.
PRINTER ERROR
RESUME?
Displayed for PictBridge.
CANNOT BE PRINTED
Displayed for PictBridge.
u PRINTING
102
Remedy
No more than 4,999 images can be shown by
date sorting.
i Protected files cannot be erased. Remove the
protection.
i Protected files cannot be added to voice
memos. Remove the protection.
i The voice memo cannot be played back.
i Contact your FUJIFILM dealer.
The image cannot be trimmed.
The image cannot be trimmed.
The maximum number of frames for which prints
can be specified on the same xD-Picture Card is
999.
Copy the images for which you want to order
prints onto another xD-Picture Card and then
specify the DPOF settings.
DPOF printing cannot be used with this image
format.
i Check that the USB cable (mini-B) is connected
correctly.
i Check that your printer is turned on.
i Check that the printer is not out of paper or out
of ink.
i Turn the printer off briefly and then turn it back
on.
i Refer to the user manual supplied with your
printer.
Check that the printer is not out of paper or out of
ink. Printing automatically restarts when the error
is cleared. If the message still appears after
checking, press the "MENU/OK" button to restart
printing.
i Refer to the user manual for the printer being
used and check whether the printer supports the
JFIF-JPEG or Exif-JPEG image format. If not,
the printer cannot print the images.
i Movie images cannot be printed.
i Was the image data photographed using
FinePix Z1?
You may not be able to print some images
photographed on other cameras.
This message appears when printing is performed
from a FUJIFILM printer that supports PictBridge.
Refer to the Owner's Manual for the printer for
details.
Troubleshooting
eIf you think the camera is faulty, check the following once more.
Troubleshooting Possible causes
i There is no battery in the camera.
The indicator lamp does
i The camera, AC power adapter and cradle
not light when charging
are not connected correctly.
the battery.
i The battery terminals are dirty.
The indicator lamp
blinks during charging
and the battery won't
charge.
i The battery can no longer be recharged.
i The battery has run out.
No power.
i The AC power adapter plug has come out
of the power outlet.
i The battery is loaded backward.
i The battery cover is not closed correctly.
Power cuts out during The battery has run out.
operation.
i Camera is used in extremely cold
Battery runs out quickly.
conditions.
i The terminals are soiled.
i The battery can no longer be recharged.
i No xD-Picture Card is inserted.
No photograph is taken
i The xD-Picture Card is full.
when pressing the
shutter button.
i The xD-Picture Card is not formatted.
i The xD-Picture Card contact area is
soiled.
i The xD-Picture Card is damaged.
i The Auto power off function has turned the
camera off.
i The battery has run out.
i The shutter button was pressed while the
Can't use the flash.
flash was charging.
i Photography mode is set to "
NATURAL LIGHT, " , " LANDSCAPE.
The flash settings are The Photography mode is set to "AUTO",
À , . ©
" ", " ", " " or " ".
restricted and cannot be
selected.
i The subject is too far away.
The playback image is
dark even though the
i Your finger was covering the flash.
flash was used.
i The lens is dirty.
The image is blurred.
i You photographed scenery with Macro
mode selected.
i You took a close-up shot without selecting
Macro mode.
i You are shooting a subject that is not
suited to autofocusing.
The picture was taken with a slow shutter
There is speckling on
the image. speed (long exposure) in a high-temperature
environment.
i The camera volume is set too low.
The camera does not
i The microphone was blocked during
emit any sound.
shooting/recording.
i There is something covering the speaker
during playback.
Solutions
i Load the battery.
i Connect the camera and AC power
adapter correctly.
i Take the battery out briefly and then
reload it.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new or fully charged battery. If the
battery still fails to charge, contact your
FUJIFILM dealer.
i Load a new or fully charged battery.
i Plug the adapter back in.
i Load the battery in the correct direction.
i Close the battery cover correctly.
Load a new or fully charged battery.
i Put the battery in your pocket or another
warm place to heat it and then load it into
the camera just before you take a picture.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new or fully charged battery.
i Insert an xD-Picture Card.
i Insert a new xD-Picture Card or erase
some unwanted frames.
i Format the xD-Picture Card on the
camera.
i Wipe the xD-Picture Card contact area
with a clean dry cloth.
i Insert a new xD-Picture Card.
i Turn the camera on.
i Load a new or fully charged battery.
i Wait until the charging is completed before
pressing the shutter button.
À
" i Change the Photography mode.
The flash settings are restricted because the
camera settings are tailored to the scene
being shot. Change the Photography mode
for a wider range of flash settings.
i Move to within the effective flash range
before taking the picture.
i Hold the camera correctly.
i Clean the lens.
i Cancel Macro mode.
i Select Macro mode.
i Use AF/AE lock to take the picture.
This is a characteristic of CCDs and does
not indicate a camera fault.
i Adjust the volume.
i Take care not to block the microphone
during shooting/recording.
i Make sure that the speaker is uncovered.
103