Continuous Shooting - FujiFilm FinePix S20 Pro Owner's Manual

Warning Displays
Warning Displayed Explanation
Camera malfunction or fault.
i The voice memo file is faulty.
i Camera fault.
CCD-RAW is set to ON in SET-UP.
An attempt was made to specify DPOF
settings for an image that is not supported
by DPOF.
The timing for recording was incorrect
because the media was formatted on a
computer.
You tried to shoot a movie when the
Microdrive was too hot.
When " 1394
MODE" in the SET-UP menu, the Mode
dial is set to another mode excluding the
Still photography mode.
112
Remedy
i Turn the camera on again, taking care not to
touch the lens.
i Turn the camera off and on again. If the
message is still displayed, contact your
FUJIFILM dealer.
i The voice memo cannot be played back.
i Contact your FUJIFILM dealer.
Set CCD-RAW to OFF in SET-UP (➡P.83).
DPOF printing cannot be used with this image
format.
Use media that was formatted on the camera.
Turn the camera off and stop using it for about 30
minutes until it has cooled down. Note that you
can still shoot still images during this time.
" is selected in "1394 i When taking pictures using PC, set the Mode
dial to the Still photography mode.
i Select " " in "1394 MODE" in the SET-UP
menu.
Troubleshooting
eIf you think the camera is faulty, check the following once more.
Troubleshooting Possible causes
i The batteries have run out.
No power.
i The batteries are loaded backwards.
i The battery cover is not closed properly.
i The AC power adapter plug has come
out of the power outlet.
Power cuts out during The batteries run out.
operation.
i You are using the camera in extremely
Batteries run out
quickly. cold conditions.
i The terminals are soiled.
i The batteries get un-rechargeable.
No photograph is taken i No media is inserted.
when the shutter button i The media is fully recorded.
is pressed.
i The media is not formatted.
i The xD-Picture Card contact area is
soiled.
i The media is damaged.
i The Auto Power Off function has
switched the camera off.
i The batteries run out.
Focusing is slow. i The ADAPTER menu in the "SET-UP"
menu is "YES".
i The external AF sensor is dirty.
Can't set the camera to The camera is set to Scene position mode
Macro (close-up) mode. or to Movie mode.
Can't select continuous Multiple exposure mode is selected.
shooting.
Can't set exposure The Photography mode is set to Auto,
compensation. Scene position or Manual.
Can't use the flash. i The flash is not popped up.
i You pressed the Shutter button while the
flash was charging.
i The batteries run out.
i The camera is set to Scenery in Scene
position mode.
i Continuous shooting is selected.
i Super Macro mode is selected.
The flash settings are
Scene position mode is selected.
restricted and cannot
be selected.
Can only select Continuous shooting is selected.
Suppressed flash mode.
Can only select the " " i The sensitivity is set to 1600 (high-sensitivity
quality setting. photography).
i The Continuous shooting option in the
photography menu is set to "Long-period

continuous shooting".

The playback image is i The subject is too far away.
too dark even though
the flash was used. i Your finger was covering the flash/flash
control sensor.
Solutions
i Load new or fully charged batteries.
i Load the batteries in the correct direction.
i Close the battery cover correctly.
i Plug the adapter back in.
Load new or fully charged batteries.
i Put the batteries in your pocket or another
warm place to heat them and then load
them into the camera just before you take
a picture.
i Wipe the battery terminals with a clean,
dry cloth.
i Load new or fully charged batteries.
i Insert a media.
i Insert a new media or erase some
unwanted frames.
i Format the media.
i Wipe the xD-Picture Card contact area
with a clean dry cloth.
i Insert a new media.
i Turn the camera on.
i Load new or fully charged batteries.
i If you are not using an adapter, select
the "NO" setting.
i Use a blower brush to brush away any
dust and then gently wipe the sensor
with a soft, dry cloth.
Photography mode is changed to " ",
" ", " ", " " or " ".
Set Multiple exposure mode to "OFF".
Change the photography mode.
i Pop up the flash.
i Wait until the flash has finished charging
before pressing the Shutter button.
i Load new or fully charged batteries.
i Select another Scene position or change
the Photography mode.
i Set Continuous shooting to "OFF".
i Cancel Super Macro mode.
The flash settings are restricted because
the camera settings are tailored to the
scene being shot. Change the Photography
mode for a wider range of flash settings.
Set Continuous shooting to "OFF".
i Set the sensitivity to 800 or less.
i Set the Continuous shooting option to
something other than "Long-period
continuous shooting".
i Move to within the effective flash range
before taking the picture.
i Hold the camera correctly.
113