Warning Displays - FujiFilm FinePix A120 Owner's Manual

Warning Displays

eThe table below lists the warnings that are displayed on the LCD monitor.
Warning Displayed Explanation
The batteries in the camera are fully
(Lit red)
depleted or very low on charge.
(Blinking red)
There is a strong likelihood of camera
|
shake because the shutter speed is
slow.
Outside the AE continuous range.
No xD-Picture Card is inserted.
i The xD-Picture Card is not
formatted.
i The xD-Picture Card contact area
is soiled.
i Camera fault.
i The xD-Picture Card contact area
is soiled.
i The xD-Picture Card is damaged.
i The xD-Picture Card format is
incorrect.
i Camera fault.
The xD-Picture Card is fully
recorded.
i The file played back was not
recorded correctly.
i The xD-Picture Card contact area
is soiled.
i Camera fault.
i You attempted to play a movie that
was not recorded on this camera.
The frame number has reached
999–9999.
i The data could not be recorded due
to an xD-Picture Card error or a
connection error between the xD-
Picture Card and camera.
i The image cannot be recorded as it
is too large to fit in the available
space on the xD-Picture Card.
A protected file was encountered.
Prints were specified for 1000 or
more frames in the DPOF frame
settings.
74
Remedy
Load new or fully charged batteries.
Use flash photography. However, use a
tripod for some scenes and modes.
The picture can be taken, but the correct
brighthess (exposure) will not be obtained.
Insert an xD-Picture Card.
i Format the xD-Picture Card in the
camera.
i Wipe the contact area on the xD-Picture
Card with a soft dry cloth. It may be
necessary to format the xD-Picture Card.
If the error message is still displayed,
replace the xD-Picture Card.
i Contact your FUJIFILM dealer.
i Wipe the contact area on the xD-Picture
Card with a soft dry cloth. It may be
necessary to format the xD-Picture Card.
If the error message is still displayed,
replace the xD-Picture Card.
i Contact your FUJIFILM dealer.
Erase some images or use an xD-Picture
Card that has ample free space.
i Images cannot be played back.
i Wipe the contact area on the xD-Picture
Card with a soft dry cloth. It may be
necessary to format the xD-Picture Card.
If the error message is still displayed,
replace the xD-Picture Card.
i Contact your FUJIFILM dealer.
i Movies cannot be played back.
1 Insert a formatted xD-Picture Card into
the camera.
2 Set "RENEW" as the FRAME NO.
setting in the SET-UP menu.
3 Start taking pictures. (The frame
numbers start from "100-0001".)
4 Set "CONT." as the FRAME NO. setting
in the SET-UP menu.
i Re-insert the xD-Picture Card or turn the
camera off and then on again. If the error
message is still displayed, contact your
FUJIFILM dealer.
i Use a new xD-Picture Card.
Protected files cannot be erased. Remove
the protection.
The maximum number of frames for which
prints can be specified on the same xD-
Picture Card is 999.
Copy the images for which you want to
order prints onto another xD-Picture Card
and then specify the DPOF settings.
Warning Displayed Explanation
Movie selected in the DPOF settings.
Displayed for PictBridge.
Displayed for PictBridge.
Displayed for PictBridge.
Displayed for PictBridge.
Displayed for PictBridge.
Remedy
You cannot use DPOF to order prints of
movies.
i Check that the USB cable is connected
properly.
i Check that your printer is turned on.
i Check that the printer is not out of paper
or out of ink.
i Turn the printer off briefly and then turn it
back on.
i Refer to the user manual supplied with
your printer.
Check that the printer is not out of paper or
out of ink. Printing automatically restarts
when the error is cleared. If the error
message still appears after checking, press
the "MENU/OK" button to restart printing.
i Refer to the user manual for the printer
being used and check whether the printer
supports the JFIF-JPEG or Exif-JPEG
image format. If not, the printer cannot
print the image (s).
i Movie images cannot be printed.
i Was the image data photographed using
FinePix A120?
You may not be able to print some images
photographed on other cameras.
This message appears when printing is
performed from a FUJIFILM printer that
supports PictBridge. Refer to the user
manual for the printer for details.
75