Checking The Programme List - Sharp AQUOS LC-20B5E Operation Manual

8
Press \/| to select "Ch".
• When you press ', channels are displayed in forward
direction.
• When you press ", channels are displayed in backward
direction.
M e n u [ C a r d M e n u [ C a r d T i m e r
S e t u p S e t u p
A d j u s t T i m e r
D a t e D a t e S t a r t S t a r t
1 3 / 0 5 T h u 1 9 : 4 5
: SELECT O K : ENTER M : BACK
NOTE
• Programmes set for Child Lock or set to "On" in "Skip" are not
displayed.
9
Press \/| to select "Mode", and press '/" to select
either "SP", "LP", "EP" or "FIT".
M e n u [ C a r d M e n u [ C a r d T i m e r
S e t u p S e t u p
A d j u s t T i m e r
D a t e D a t e S t a r t S t a r t
1 3 / 0 5 T h u 1 9 : 4 5
: SELECT O K : ENTER M : BACK
NOTE
• The recording is performed within the times set. When there is no
remaining time on the card, the message "Remaining Time 0:00" is
displayed and the recording will be interrupted. In this case, use
another card or delete recorded files to make more space. (See
page 45 for deleting files)
• FIT refers to automatic recording while adjusting image quality
between SP and LP so that the recording is completed within the
specified time. It may not be possible to record using FIT depend-
ing on the remaining capacity of the card.
• Two recordings cannot be programmed simultaneously for FIT.
10
Press \/| to select "Set", and press '/" to select
either "On", "Off" or "CLR".
M e n u [ C a r d M e n u [ C a r d T i m e r
S e t u p S e t u p
A d j u s t T i m e r
D a t e D a t e S t a r t S t a r t
1 3 / 0 5 T h u 1 9 : 4 5
: SELECT O K : ENTER M : BACK
11
Press OK to set the timer.
12
Press END to exit.
NOTE
• Timer programming settings are cancelled when the duration
of the power outage exceeds the backup time. (See page 21.)
r e c ]
R e c . s e t t i n g
S t o p S t o p C h C h M o d e M o d e S e t S e t
~ 2 1 : 4 5 0 0 1 S P O n
E : EXIT
r e c ]
R e c . s e t t i n g
S t o p S t o p C h C h M o d e M o d e S e t S e t
~ 2 1 : 4 5 0 0 1 S P O n
E : EXIT
r e c ]
R e c . s e t t i n g
S t o p S t o p C h C h M o d e M o d e S e t S e t
~ 2 1 : 4 5 0 0 1 S P O n
E : EXIT
Setting Timer Recording (Continued)

Checking the Programme List

You can check the current recording states in the list.
1
Perform steps 1 to 3 in Timer Rec to display the "Timer
rec" screen.
2
Press \/| to select "Programme list", and press OK.
M e n u [ C a r d M e n u [ C a r d T i m e r
P r o g r a m m e l i s t
S e t u p S e t u p
Press '/" to select the file you want to check, and
3
: SELECT O K : ENTER M : BACK
press OK.
M e n u [ C a r d M e n u [ C a r d T i m e r T i m e r
P r o g r a m m e P r o g r a m m e l i s t l i s t
1 3 / 0 5 T h u 1 9 : 4 5 ~ 2 1 : 4 5
1 4 / 0 5 F r i 2 1 : 0 0
1 5 / 0 5 S a t 1 9 : 0 0
4
Press END to exit.
: SELECT O K : ENTER M : BACK
To change the programme
In the step 3 above, press '/" to select the programme to be
changed or clear, and press OK.
Press \/| to select the desired item, and adjust with '/".
r e c ]
P r o g r a m m e P r o g r a m m e l i s t l i s t
E : EXIT
r e c ] r e c ]
0 0 1 S P O n
~ 2 2 : 0 0 0 1 5 E P O n
~ 2 1 : 0 0 0 1 5 S P O n
E : EXIT
39