Packard Bell reserves the right to make changes to the EasyNote GN45 without notice. Technician Notes Only technicians authorized by Packard Bell B.V. should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair.
Non personal injury. Always return a defective power avviare il sistema senza aver prima messo supply to your dealer. a posto il coperchio. Packard Bell EasyNote GN45 Disassembly Manual...
To remove the hard disk drive, first remove the battery (see Battery) and then perform the following steps: 1. Remove the screws on the hard disk drive cover and carefully open it. Fig. 2 Removing the hard disk drive cover. Packard Bell EasyNote GN45 Disassembly Manual...
To remove the optical disk drive, first remove the battery (see Battery) and then perform the following steps: 1. Release the screw securing the optical disk drive. Fig. 5 Releasing the optical disk drive. Packard Bell EasyNote GN45 Disassembly Manual...
To remove the memory module, first remove the battery (see Battery) and then perform the following steps: Release the screws retaining the memory module slot cover. Fig. 7 Removing the memory slot cover. Remove the memory module from the slot and put it aside. Packard Bell EasyNote GN45 Disassembly Manual...
2. Disconnect the wireless antenna cables (red circles on Fig. 9). Fig. 9 Removing the WLAN card. 3. Remove the two screws securing the WLAN card (yellow circles on Fig. 9). 4. Lift the card from the main board. Packard Bell EasyNote GN45 Disassembly Manual...
Fig. 10 Left keyboard back screw. Fig. 11 Right keyboard back screw. 2. Use a small screwdriver to unlock the keyboard cover on both sides. Fig. 12 Releasing the keyboard cover. 3. Remove both screws securing the keyboard. Packard Bell EasyNote GN45 Disassembly Manual...
Optical Disk Drive), remove the keyboard cover (see Keyboard), Remove the Express Card (if needed), and then perform the following steps: 1. Turn the notebook upside down and remove all screws securing the bottom cover. Packard Bell EasyNote GN45 Disassembly Manual...
To remove the LCD module, remove the keyboard top cover (see Keyboard) and then perform the following steps: 1. Remove the four screws holding the LCD module 2. To disconnect the video cable, carefully pull the plastic part upward. Packard Bell EasyNote GN45 Disassembly Manual...
1. Remove the screw securing the LCD cover next to the hinge on each side. Fig. 18 Removing the LCD cover screws. 2. Remove the LCD top cover. Fig. 19 Removing the LCD cover. Packard Bell EasyNote GN45 Disassembly Manual...
2. Pull the main board towards the right side and upward to extract it from the casing. To remove the CPU, first remove the main board (see Main Board) and then perform the following steps: 1. Remove the screws securing the heat sink. Packard Bell EasyNote GN45 Disassembly Manual...
Express Card Reader To remove the Express Card reader, remove the top cover (see Cover) and then do the following: 1. Remove the two screws securing the Express Card reader. Fig. 24 Express card reader slot. Packard Bell EasyNote GN45 Disassembly Manual...
To remove the power button / WiFi / ECO card, first remove the keyboard top cover (see Keyboard) and then perform the following steps: 1. Remove the two screws holding the card. 2. Carefully disconnect the flat cable. Packard Bell EasyNote GN45 Disassembly Manual...
Page 16
1515151515 Fig. 27 Removing the power button/ WiFi / ECO card. Packard Bell EasyNote GN45 Disassembly Manual...
This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from Packard Bell B.V. PACKARD BELL B.V. SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN;...