Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sanyo HV-DX1E
Summary of Contents for Sanyo HV-DX1E
- Page 1 HV-DX1E INSTRUCTION MANUAL DVD Player + Video Cassette Recorder Only cassettes marked can be used with this DVD+VCR. PA L Please read this manual carefully before connecting your DVD+VCR and operating it for the first time. Keep the manual in a safe place for future reference.
-
Page 2: Safety Precautions
DVD+VCR do not contain mercury. However, SERIAL NUMBER: The serial number is found on the back of SANYO recommends that you do not dispose this unit. This number is unique to this unit and not available to of used batteries with domestic refuse. -
Page 3: Table Of Contents
Contents Introduction Operation with Audio CD and MP3 Discs ..29 Playing Audio CD and MP3 Discs ....29 Safety Precautions ......2 Pause . -
Page 4: Before Use
Before Use Playable Discs Disc-related terms Title (DVD only) The main film content or accompanying feature content or additional feature content, or music album. Each title (8 cm / 12 cm disc) is assigned a title reference number enabling you to Video CD (VCD) locate it easily. -
Page 5: Precautions
Before Use (Cont’d) Precautions Cleaning discs Fingerprints and dust on the disc can cause poor pic- Handling the unit ture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the cen- When shipping the unit ter out. -
Page 6: Front Panel
Front Panel Disc Tray (DVD deck) EJECT(Z Z ) Insert a disc here. Ejects the tape in the VCR deck. CHANNEL (+/-) To scan up or down through memorized channels. Cassette Compartment (VCR deck) Insert a video cassette here. Remote Sensor Point the DVD+VCR remote control here. -
Page 7: Display Window
Display Window CD Audio CD inserted DVD inserted VCD Video CD inserted y B Indicates A-B repeat mode. ALL Indicates repeat all mode. ANGLE active. MP3 MP3 disc inserted. PROG. Programmed playback active. TITLE Indicates current title number. CHP/TRK Indicates current chapter or track number. VCR DVD+VCR functions are available and channels are selected at DVD+VCR. -
Page 8: Remote Control
Remote Control DVD/VCR select button OPEN/CLOSE, EJECT (Z Z ) Select the output source (DVD or VCR) to - Opens and closes the disc tray. view on the TV screen. - Ejects the tape in the VCR deck. OUTPUT SELECT Cycles through the 3 main output views: Switches DVD+VCR ON and OFF. -
Page 9: Rear Panel
Rear Panel AUDIO OUT (Left/Right) Connect to an amplifier, receiver or stereo system. COAXIAL (Digital audio out jack) Connect to digital (coaxial) audio equipment. AERIAL Connect the aerial using this jack. EURO AV2 DECODER Connect to another video recorder. DVD EXCLUSIVE OUT VHS IN+OUT/DVD OUT AUDIO DIGITAL... -
Page 10: Connections
Connections This DVD+VCR operates on a mains supply of POWER: Tips 200-240V~, 50Hz Depending on your TV and other equipment you wish This appliance is supplied with BS 1363 approved 13 Amp fused mains plug. When replacing the fuse to connect, there are various ways you could connect always use a 5 Amp BS 1362 approved type. -
Page 11: Connecting To Optional Equipment
Connections (Cont’d) Connecting to Optional Equipment Notes – If the audio format of the digital output does not match Connecting to an amplifier equipped with two the capabilities of your receiver, the receiver will channel analog stereo or Dolby Surround produce a strong, distorted sound or no sound at all. -
Page 12: Before Operation - Vcr Part
Before Operation - VCR part Video channel Set Using your DVD+VCR for the very first time Video channel (RF output channel) is the channel on For the following steps we assume that you have just which your TV receives picture and sound signals from connected your DVD+VCR for the very first time. -
Page 13: How To Use The Main Menu
Before Operation - VCR part How to use the main menu Tuning in TV Stations Automatically This DVD+VCR can easily be programmed by using the Should you wish to perform the Automatic Channel menus displayed on screen. Memory System (ACMS) again please follow the guid- The menus are controlled from the Remote Control ance given on this page. -
Page 14: Tuning In Tv Stations Manually
Before Operation - VCR part Tuning in TV Stations Manually Searching will stop when it locates a station. If the station transmits PDC, the station name will In certain areas of the country broadcast signals may be added automatically. be too weak for your DVD+VCR’s automatic tuning Control the fine tuning of the station by pressing process to find or assign TV stations correctly. -
Page 15: Changing The Order Of Tv Stations
Before Operation - VCR part Changing the order of TV Stations Deleting TV Stations After tuning TV stations into your DVD+VCR you may After tuning TV stations into your DVD+VCR you may wish to change the order in which they are stored with- wish to delete a station. -
Page 16: Setting The Clock Manually
Before Operation - VCR part Setting the clock Manually To set the colour system The clock in your DVD+VCR controls time, day and Your DVD+VCR is equipped with dual colour standard, date settings for your DVD+VCR. you can play back a tape in PAL and MESECAM. For VIDEO Plus+ system to work correctly the cor- During playback your DVD+VCR detects the colour sys- rect time and date must be set. -
Page 17: Before Operation - Dvd Part
Before Operation - DVD part General Explanation Temporary Feedback Field Icons Repeat Title This manual gives the basic instructions for operating TITLE the DVD+VCR. Some DVDs require specific operation Repeat Chapter CHAPT or allow only limited operation during playback. When Repeat Track (non-PBC Video CDs only) TRACK this occurs, the symbol... -
Page 18: Initial Settings
Before Operation (Continued) - DVD part Initial Settings Menu Language Select a language for the setup menu. This is the menu You can set your own Personal Preferences on the you see when you press SETUP. DVD+VCR. General Operation English Disc Audio Disc Subtitle Spanish... -
Page 19: Sound
Before Operation (Continued) - DVD part Sound Others Digital Audio Output The DRC, Vocal and PBC settings can be changed. Press 3 3 /4 4 to select the desired item and press Each DVD disc has a variety of audio output options. SELECT/OK. -
Page 20: Parental Control
Before Operation (Continued) - DVD part Parental Control Country Code Enter the code of a country/area whose standards were Rating used to rate the DVD video disc, referring to the list Movies on DVDs may contain scenes not suitable for (See “Country Code List”, page 38). -
Page 21: Operation With Tape
Operation with tape Playing a tape During playback or still picture press You can reach the following playback speeds. You will only be able to load and eject video cassettes (-7xplay, -3xplay, -play, still, 1/19 slow, play, 2xplay, when your DVD+VCR is plugged into the mains. 7xplay) Your DVD+VCR may also play back recordings from To switch off the slow motion and shuttle, press the... -
Page 22: Quick Set Recording (Qsr)
Operation with tape The DVD+VCR allows you to make recordings using a Press SP/LP if you wish to record in Long Play variety of simple methods: or Standard Play. Quick Set Recording (QSR): Start recording immedi- SP will produce improved picture and sound quality, ately for a set period of time or until the video cassette however LP will provide twice as much recording runs out. -
Page 23: Video Plus+ ® System Recording
Operation with tape VIDEO Plus+ ® System recording DATE T I M E BBC1 11 11 55 - - - - - - - - - - - - - - - - VIDEO Plus+ System greatly simplifies entering the - - - - - - - - - - - - - - - - date, channel, start and end times of a Timer recording... -
Page 24: Timer Recording Using On Screen Display
Operation with tape Timer recording using On Screen Press the numerical buttons to enter the date of the programme. Display If you press OK before entering the date you may select one of the following automated If you choose not to use VIDEO Plus+ System recording features. - Page 25 Operation with tape If Timer record events Overlap... Change (Deleting) the Timer Programme Do not overlap programmes, since overlapping portions If at a later date you wish to delete or change any of of the conflicting programmes will not be recorded. the settings in timer event memory you may do so with- Earlier recording times have priority over later recording out having to enter all the timer event information again.
-
Page 26: Operation With Dvd And Video Cd
Operation with DVD and Video CD Playing DVD and Video CD General Features Playback Setup VCD2.0 VCD1.1 Note Unless stated otherwise, all operations described use Turn on the TV and select the video input source con- the remote control. Some features may also be avail- nected to the DVD+VCR. -
Page 27: Still Picture And Frame-By-Frame Playback
Operation with DVD and Video CD General Features (continued) Video CDs - Repeat Track/All/Off 1 To repeat the track currently playing, press REPEAT. Still Picture and Frame-by-frame playback The Repeat Track icon appears on the TV screen. 2 To repeat the disc currently playing, press REPEAT a VCD2.0 VCD1.1 second time. -
Page 28: Zoom
Operation with DVD and Video CD General Features (continued) Special DVD Features Zoom VCD2.0 VCD1.1 Checking the contents of DVD Video discs: Menus The Zoom function allows you to enlarge the video image and to move through the enlarged image. DVDs may contain menus that allow you to access spe- 1 Press ZOOM during playback or still playback to acti- cial features. -
Page 29: Operation With Audio Cd And Mp3 Discs
Operation with Audio CD and MP3 Discs Playing Audio CD and MP3 discs Search 1 Press and hold BACKWARD . or FORWARD > The DVD+VCR can play MP3 formatted recordings on for about two seconds during playback. CD-R or CD-RW discs. The player will now go into SEARCH mode. -
Page 30: Programmed Playback
Programmed Playback VCD2.0 VCD1.1 Programmed Playback with Audio CD Programmed Playback with Video CD and MP3 Discs Note Programme allows you to store your favorite tracks for a On a Video CD with PBC, you must set PBC to Off on the particular disc in the player memory. -
Page 31: Additional Operation - Vcr Part
The Digital Tape Counter indicates the relative positions cleaning cassette. of recordings on the tape. If noise still remains in the playback picture, contact your SANYO authorized service agent. Press CLK/CNT repeatedly until the counter is TAPE STATUS displayed on the TV screen. -
Page 32: Hi-Fi Stereo Sound System
Additional Operation - VCR part Hi-Fi Stereo Sound System Widescreen Compatibility 16:9 Your DVD+VCR will record and play back Hi-Fi stereo Your DVD+VCR can record and play back widescreen sound. In addition it has a NICAM digital stereo sound aspect ratio programmes (16:9). To record a wide decoder. -
Page 33: Additional Operation - Dvd Part
Additional Operation - DVD part Video Mode Setting Notes on MP3 Discs VCD2.0 VCD1.1 About MP3 With certain discs, the playback picture may be flick- ering or Dot Crawl is shown on straight lines. That An MP3 file is audio data compressed by using means Vertical interpolation or De-interlace is not MPEG1, the audio layer-3 file-coding scheme. -
Page 34: Special Recording
Special Recording Copying from DVD To VCR Recording from another video This unit allows you to copy the contents of a DVD to a recorder VHS tape. With the DVD+VCR you can make recordings from an external source, such as copying from another VCR or Note a camcorder. -
Page 35: Troubleshooting
Troubleshooting - DVD part Check the following guide for the possible cause of a problem before contacting service. Symptom Cause Correction DVD or VCR do not DVD or VCR button is not switched Refer to page 8. work properly. properly. Plug the mains lead into the wall outlet No power. - Page 36 Troubleshooting - VCR part Symptom Cause Correction The tape does not run The DVD+VCR is in the RECORD Press PAUSE/STEP (X X ) to resume PAUSE MODE. recording. during recording. The tape will not rewind The tape is already fully rewound or Check the tape.
-
Page 37: Language Code List
Language Code List Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu” (See page 18). Code Language Code Language Code Language Code Language 6566 Abkhazian 7074 Fiji 7678 Lingala 8373 Singhalese 6565 Afar 7073 Finnish 7684... -
Page 38: Country Code List
Country Code List Enter the appropriate code number for the initial setting “Country Code” (See page 20). Code Country Code Country Code Country Code Country Andorra Eritrea Saint Lucia Seychelles United Arab Emirates Spain Liechtenstein Sudan Afghanistan Ethiopia Sri Lanka Sweden Antigua and Barbuda Finland... -
Page 39: Specification
Specification General Power requirements AC 200-240 V , 50 Hz Power consumption 23 W Dimensions (approx.) 430 X 97.5 X 360 mm (w x h x d) Mass (approx.) 5.3 kg (11.7 lbs) Operating temperature 5˚C to 40˚C (41˚F to 104˚F) Timer 24-hour display type Operating humidity... - Page 40 4. Should the equipment require servicing after the expiry of the guarantee period, take or send it to the original supplier or any other Sanyo dealer. He will be pleased to give you a quotation for the repair. If you are in any doubt about what to do, write to us at the address below or telephone: Sanyo Europe Ltd.