Aerials; Operating Instructions; Tuning And Listening; Dab Station Full Scan - Cambridge Audio AZUR 650T User Manual

Aerials

RS232
Power Rating : 220 - 230V AC ~ 50/60Hz
Max Power Consumption: 15W
Power AC Power
Control Bus IR Emitter
On Off
In Out In
RS232
Power Rating : 115V AC ~ 50/60Hz
Max Power Consumption: 15W
Power AC Power
Control Bus IR Emitter
On Off
In Out In
Note: The 650T is supplied with temporary FM or DAB aerials for initial use
only. For permanent use, outdoor aerials are highly recommended.
AM loop aerial
Connect each end of the single length antenna to the antenna terminals.
Place the antenna as far from the main system as possible to prevent
unwanted noise and to obtain optimum reception. If the AM loop aerial
provided does not receive sufficient reception, it may be necessary to use
an outdoor AM aerial.
FM aerial
Connect the supplied aerial to the FM 75 ohm socket. Extend and move
the aerial lead around until you get the best reception. For continued use,
we strongly recommend using a 75 ohm outdoor FM aerial.
DAB aerial
The 650T has a 50 Ω F-type screw connection aerial for DAB signal.
Connect the supplied DAB aerial to the socket. For continued use, we
strongly recommend an external aerial.
Note: It is desirable to separate the DAB and FM aerials for best
performance.
SIRIUS ready (CU version only)
Note: Do not use any power supply with your SIRIUS module. The 650T
unit will power your SIRIUS module.
The SIRIUS socket allows the connection of a SIRIUS satellite radio
reception module (require subscription). Consult your dealer for more
information. For continued use, we strongly recommend an external
aerial.
8
Designed and engineered in London, England
Output Line
azur 650T AM/FM/DAB Tuner
www.cambridge-audio.com
Digital Outputs AM 300Ω FM 75Ω
Left Left
F-Type Aerial Input
Ohms 50 50 Ohms
Right Input Aerial F-Type
Toslink S/P DIF
Line Output
Optical Co-axial
Designed and engineered in London, England
Output Line azur 650T AM/FM/SIRIUS Tuner
www.cambridge-audio.com
Left Left AM 300Ω FM 75Ω
Right
Line Output
For use with external
Sirius module only

Operating instructions

After making the connections to your unit, activate the 650T by switching
the power button on the rear panel to 'On', then press the Standby/On
button on the front of the unit or remote.
Note: When used for the first time, the unit will peform a DAB full scan
when turned on.

Tuning and listening

Press the Standby/On button.
Press the Band button to toggle between bands.
In FM/AM mode, use the
increments or press and hold the
DAB mode (DAB version only)
Because DAB stations are transmitted in digital multiplexes containing
several stations bundled together the 650T needs to scan and find the
available multiplexes in your area before it can allow you to step through
the stations they contain.
The quick scan scans all the most common bands for multiplexes, whilst
the full scan will scan all possible DAB frequencies and may take up to a
couple of minutes to complete.
Performing a scan is only required at first setup and perhaps occasionally
afterwards to see if any new services have been added in your area.
If you are using the 650T for the first time or have moved to a different
geographic location always perform a full scan. It is recommended to
perform a factory reset before performing a full scan to erase all stored
presets and existing stations.
Quick scan is accomplished by briefly pressing the Autotune button.
Full scan is accomplished by pressing and holding the Autotune button.
Once a scan has been performed, use the
through receivable station. Then press Select/Mode to listen to your
chosen station.
Note: DAB mode the 650T can be set to Autoselect On or Off. When On if
you browse to a station in the display (using the
press nothing for a few seconds, the display will automatically tune to that
station.
When Off you need to press Select after browsing to a station to tune to
that station (if nothing is pressed the 650T reverts to the current station
after a couple of seconds).
Press and hold the Select/Mode button to set Autoselect On. Press and
hold again the Select/Mode button to set Autoselect Off
DAB settings
It is possible to change the DAB region setting for this unit. This is
necessary if the unit has been moved to a different region location.
Note: Changing the DAB region will erase all the stored DAB presets.
1. Press and hold the Select/Mode button when powering up the unit to
access the advance setting.
2. Use the buttons and select 'DAB settings'. Press the
Select/Mode button to change the DAB region settings.
3. Use the buttons to browse through the available country DAB
region setting Europe, Canada, Korea and China.
4. Select the correct region and press the Select/Mode button to accept
the new changes.
5. Restart the unit and perform a full station scan.
buttons to manually tune in 0.05MHz
or button.
buttons to browse
buttons) and then