Table of Contents
Advertisement
Quick Links
Trademarks
Copyright © PLANET Technology Corp. 2003
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trade-
marks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representa-
tion, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User's Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User's Manual is subject to change without notice and does
not represent a commitment on the part of PLANET. PLANET assumes no re-
sponsibility for any inaccuracies that may be contained in this User's Manual.
PLANET makes no commitment to update or keep current the information
in this User's Manual, and reserves the right to make improvements to this
User's Manual and/or to the products described in this User's Manual, at any
time without notice.
If you find information in this manual that is incorrect, misleading, or incom-
plete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
Revision
PLANET 16/24-port + 2-slot Fast Ethernet Switch User's Manual
FOR MODEL: FNSW-1602, FNSW-2402
Part No.: 2010-000024-000
Advertisement
Table of Contents
Related Manuals for Planet FNSW-2402
Summary of Contents for Planet FNSW-2402
-
Page 1: Fcc Warning
Trademarks Copyright © PLANET Technology Corp. 2003 Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trade- marks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work properly in... -
Page 2: Table Of Contents
Table of Contents Chapter 1 Introduction 1.1 Package Contents 1.2 How to Use This Manual 1.3 Product Features 1.4 Product Specifications Chapter 2 Installation 2.1 Product Description 2.2 Installing a Switch Chapter 3 Switch Operation 3.1 Address Table 3.2 Learning 3.3 Forwarding &... -
Page 3: Chapter 1 Introduction
It contains troubleshooting guide of FNSW-1602/FNSW-2402. • Appendix A It contains cable information of FNSW-1602/FNSW-2402. In the following section, the term “Switch” means the two Switches, i.e. FNSW-1602/ FNSW-2402, term of “switch” or “Ethernet switch” can be any third part switches. -
Page 4: Product Features
1.3 Product Features • Complies with IEEE802.3 and 802.3u standards for 100Base-TX/FX • 16/24-port 10/100 Mbps Fast Ethernet Switch • Each Switching ports support auto-negotiation-10/20, 100/200Mbps sup- ported • 2 open slots for 10/100Base-TX and 100Base-FX fiber-optic interface with vari- ous connection media and distances •... -
Page 5: Product Specifications
1.4 Product Specifications Model FNSW-1602 FNSW-2402 Hardware Specification Network ports Module slot 2 open slots for 10/100Base- TX and 100Base-FX fiber- optic interface Dimensions 440 x 200 x 44 mm (1U height) Weight 2.6 kg Power Requirement 100~240 (±10%) VAC, 50-60 (±3) Hz... -
Page 7: Chapter 2 Installation
Chapter 2 INSTALLATION This section describes the functionalities of FNSW-1602/FNSW-2402 components and guides how to install it on the desktop or shelf. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 2.1 Product Description The PLANET Switch provides 16/24 10/100Mbps Fast Ethernet ports with 2 open slots (port#17/25, port#18/26). -
Page 8: Installing A Switch
Note: The 100Base-FX modules only support full-duplex mode. 2.1.6 FNSW-1602 and FNSW-2402 Rear Panel The rear panel of the Switch indicates an AC inlet power socket and power switch, which accepts input power from 100 to 240VAC, 50-60Hz. -
Page 9: Desktop Installation
2.2.1 Desktop Installation To install a Switch on a desktop or shelf, simply complete the following steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the switch. Step2: Place the Switch on a desktop or shelf near an AC power source. Step3: Keep enough ventilation space between the switch and the surrounding objects Note: When choosing a location, please keep in mind the environmental re-... - Page 10 Figure 2-4 Attaching the brackets to the Switch (example on FNSW-1602) Caution: You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty. Step3: Secure the brackets tightly. Step4: Follow the same steps to attach the second bracket to the opposite side.
-
Page 11: Chapter 3 Switch Operation
Chapter 3 SWITCH OPERATION 3.1 Address Table The Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Ethernet Switch. -
Page 12: Auto-Negotiation
The Switch performs “Store and forward” therefore, no error packets occur. More reliably, it reduces the re-transmission rate. No packet loss will occur. 3.5 Auto-Negotiation The STP ports on the Switch have built-in “Auto-negotiation”. This technology automatically sets the best possible bandwidth when a connection is established with another network device (usually at Power On or Reset). -
Page 13: Chapter 4 Troubleshooting
Chapter 4 TROUBLESHOOTING This chapter contains information to help you solve problems. If the Ethernet Switch is not functioning properly, make sure the Ethernet Switch was set up according to instructions in this manual. The LNK LED is not lit Solution: Check the cable connection and remove duplex mode of the Ethernet Switch The 100Base-FX fiber module’s link LED and FDX LED is not lit... -
Page 15: Appendix A
Appendix A A.1 Switch's RJ-45 Pin Assignments When connecting your 10/100Mbps Ethernet Switch to another switch, a bridge or a hub, a straight or crossover cable is necessary. Each port of the Switch supports auto-MDI/ MDI-X detection. That means you can directly connect the Switch to any Ethernet devices without making a crossover cable. - Page 16 There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Figure A-1: Straight-Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network.
- Page 17 Part No.:2010-000024-000...