Table of Contents
Advertisement
Quick Links
20" (50.8 CM) FREESTANDING ELECTRIC RANGE
RANGE SAFETY .............................................................................2
INSTALLATION REQUIREMENTS ................................................3
Tools and Parts ............................................................................3
Location Requirements................................................................3
Electrical Requirements ...............................................................5
INSTALLATION INSTRUCTIONS ..................................................6
Unpack Range..............................................................................6
IMPORTANT:
Save for local electrical inspector's use.
W10459122A
INSTALLATION INSTRUCTIONS
with Standard Clean Oven
Table of Contents
Install Anti-Tip Bracket.................................................................6
Electrical Connection ...................................................................7
Verify Anti-Tip Bracket Is Installed and Engaged ......................11
Level Range................................................................................12
Complete Installation .................................................................12
Check Operation ........................................................................12
Advertisement
Table of Contents
Related Manuals for Whirlpool W10459122A
Summary of Contents for Whirlpool W10459122A
-
Page 1: Table Of Contents
INSTALLATION REQUIREMENTS ..........3 Verify Anti-Tip Bracket Is Installed and Engaged ......11 Tools and Parts ................3 Level Range................12 Location Requirements..............3 Complete Installation ..............12 Electrical Requirements ...............5 Check Operation ................12 INSTALLATION INSTRUCTIONS ..........6 Unpack Range................6 IMPORTANT: Save for local electrical inspector's use. W10459122A... -
Page 2: Range Safety
RANGE SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER”... -
Page 3: Installation Requirements
INSTALLATION REQUIREMENTS Tools and Parts Location Requirements Gather the required tools and parts before starting installation. IMPORTANT: Observe all governing codes and ordinances. Read and follow the instructions provided with any tools listed It is the installer's responsibility to comply with installation here. - Page 4 Product Dimensions Cabinet Dimensions Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and 36" (91.4 cm) countertop height. If the cabinet depth is greater than 24" (61.0 cm), the oven frame must extend beyond cabinet fronts by ½"...
-
Page 5: Electrical Requirements
Electrical Requirements If codes permit and a separate ground wire is used, it is If connecting to a 4-wire system: recommended that a qualified electrical installer determine that This range is manufactured with the ground connected to the the ground path is adequate and wire gauge is in accordance neutral by a link. -
Page 6: Installation Instructions
INSTALLATION INSTRUCTIONS Unpack Range Install Anti-Tip Bracket WARNING WARNING Excessive Weight Hazard Use two or more people to move and install range. Failure to do so can result in back or other injury. Do not use oven door handle to lift or move the range. 2. -
Page 7: Electrical Connection
Floor Mounting 5. Using the Phillips screwdriver, mount anti-tip bracket to the wall or floor with the two #12 x 1 " screws provided. 6. Move range close enough to opening to allow for final gas and electrical connections. Remove shipping base, cardboard or hardboard from under range. - Page 8 Tighten strain relief screw against the power supply cord. Feed the flexible conduit through the strain relief, allowing enough slack to easily attach wiring to the terminal block. Tighten strain relief screw against the flexible conduit. Style 2: Direct wire strain relief Use Phillips screwdriver to remove screws and rotate/ conduit plate 180º.
- Page 9 2. Use Phillips screwdriver to remove the ground-link screw 3-wire connection: Power Supply Cord from the back of the range. Save the ground-link screw and the end of the ground-link under the screw. Use this method only if local codes permit connecting chassis 3.
- Page 10 4. Attach terminal lugs to line 1 (black), neutral (white), and line 2 Direct Wire Installation: Copper or Aluminum Wire (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through This range may be connected directly to the fuse disconnect or bottom of terminal lugs.
-
Page 11: Verify Anti-Tip Bracket Is Installed And Engaged
3. Use " nut driver to connect the bare (green) ground wire to 3-wire connection: Direct Wire the center terminal block post with one of the 10-32 hex nuts. Use this method only if local codes permit connecting ground conductor to neutral supply wire. 1. -
Page 12: Level Range
If range does not operate, check the following: Household fuse is intact and tight; or circuit breaker has not tripped. Electrical supply is connected. See “Troubleshooting” in the Use and Care Guide. W10459122A © 2012. 1/12 All rights reserved. Printed in Mexico...