General Operation; Operating Modes; Master Scenes; Flash Scenes - Elation Stage Setter 8 User Instructions

Stage Setter 8™

Operating Modes:

The Stage Setter 8™ has three different operating modes: 2x8, 8x8,
and 1x16. These modes are selected with the Mode Button (3). The
current mode is indicated by the Mode LED (3).
In 2x8 mode, Crossfader X (5) controls the channels 1-8, and Cross-
fader Y (6) controls channels 9-16.
In 8x8 mode, the Scene Y (11) channels (9-16) become a set of Masters
Scenes. Each Master Scene channel (9-16) will control the level of the
scenes or patterns created. The Scene X (2) channels (1-8) operate as
normal dimmer sliders.
In 1x16 mode, X Crossfader (5) controls the intensities of channels 1-
16, and Y Crossfader controls the Fade Time. Fade Time is the amount
of time it takes one scene to end and fade in to the next. Fade Time
varies from 1/10 of second (instant) to 10 minutes.
Masters Scenes:
Master Scenes is function that can only be used while in the 8x8 oper-
ating mode. When in the 8x8 mode, the Bump Buttons (10) and the
Scene Y (11) sliders can be used to store a Masters Scene. A Master
Scene consist of channels 1-8.
To create a Master Scene:
First, use the sliders in the Scene X (2) section to create a scene. After
you have set your scene, tap the Program Button to enter the program
mode. Once Program mode has been activated, tap the Bump Button
that corresponds to a Scene Y (11) slider that will be used to store the
scene. The scene will now be stored as a Master Scene into the Scene
Y slider and will be ready for immediate use.
Example:
We will program a into the fifth Master Scene. The scene will consist of
channels 1 and 6 at full, channel 7 at 50% and the remaining channels
fully off.
1. Move X and Y Crossfaders to maximum.
(X Crossfader fully up and Y Crossfader fully down)
Elation Professional - www.elationlighting.com - Stage Setter 8™ Instruction Manual Page 15
®

General Operation

Stage Setter 8™
Masters Scenes (Cont.):
2. Lower all Scene X sliders to minimum.
3. Raise Scene X slider 1 and 6 to maximum.
4. Raise Scene X slider 7 to 50%.
5. Tap the Program Button. The Program LED should be lit.
6. Tap Bump Button 5.

Flash Scenes:

Flash Scenes that only operates in 1x16 mode. When in the 1x16
mode, the Bump Buttons (10) can be programmed as Flash Scenes.
These are scenes that can be created by any of the 16 channels. Once
a Flash Scene is created this scene may be activate by pressing on the
Bump Button it was assigned to. To create a Flash Scene:
First, use the sliders in the Scene X (2) and Scene Y (11) section to
create a scene. After you have set your scene, tap the Program Button
to enter the program mode. Once Program mode has been activated,
tap the Bump Button that corresponds to a Scene Y slider that will
be used to store the scene. The scene will now be stored as a Master
Scene into the Scene Y slider and will be ready for immediate use.
Example:
In this example we will program Bump Button 8, allowing channels 3, 7,
14 and 15 to be at full, channel 1, 5, 10 and 16 at 50% output and the
remaining channel fully off.
1. Move all Scene X and Scene Y sliders to fully down.
2. Move Scene X sliders 3 and 7 to fully up.
3. Move Scene Y sliders 14 and 15 to fully up.
4. Move Scene X sliders 1 and 5 to 50%.
5. Move Scene Y sliders 10 and 16 to 50%.
6. Tap the Program Button causing its LED to light.
7. Tap Bump Button 8.
Elation Professional - www.elationlighting.com - Stage Setter 8™ Instruction Manual Page 16
®
General Operation