Miele G 653 Installation Instructions Manual
60 cm wide fully integrated dishwasher
Hide thumbs
Also See for G 653:
- Technical information (138 pages) ,
- Installation instructions manual (40 pages) ,
- Installation instructions manual (28 pages)
Related Manuals for Miele G 653
Summary of Contents for Miele G 653
-
Page 1: Installation Instructions
Installation instructions for 60 cm wide fully integrated dishwashers It is to read the operating and installation instructions before installing or using the machine, to avoid the risk of accident or damage to the machine. M.-Nr. 05 585 951... - Page 2 These installation instructions apply to several different dishwasher models. Model numbers in this booklet refer to the model designation specified on the data plate on the machine (and not the description on the control panel). The data plate is located on the right hand side of the door when open. The model numbers quoted refer only to the basic model number, e.g.
- Page 3 ............4 Opening the door.
- Page 4 This dishwasher is specially designed for integration under a worktop run in a fitted kitchen. – The front of the dishwasher is de- signed to take a front panel. It can be fitted with a base unit door front to match the rest of the kitchen.
- Page 5 1) Machine height 890 mm 2) Machine height 840 mm 1) Machine height 870 mm Adjustment range approx. 5 cm 2) Machine height 820 mm (84 - 89 cm total height). Adjustment range approx. 5 cm Extended machine feet are available at (82 -87 cm total height).
- Page 6 The underside of the worktop is pro- tected against steam rising from the machine by a special cover plate. A plastic holder is located on the left hand side of the cover plate for the dishwasher’s control light reflector panel. If two different materials meet up at the front edge of the worktop, then the join must be concealed by the...
- Page 7 ^ Align the cover plate to the front ^ Press the reflector panel into the edge of the worktop in the plastic holder in the cover plate. the niche. If the worktop has a edge, pull the cover plate further for- ward so that the reflector panel is still visible later on.
- Page 8 ^ Stick the doublesided adhesive strip supplied onto the back of the plastic Worktops made from hard materials holder. such as granite or marble do not need the cover plate for protection. The cover plate is only used as a guide for marking the position for the reflector panel plastic holder.
- Page 9 ^ Adjust the height manually before in- stalling the dishwasher. Connection to water and drainage Leave a space of approx. 5 mm be- should be sited beside and not behind low the worktop to allow the dish- the dishwasher for accessibility. washer to be pushed back easily into Connections are usually made in the the recess.
- Page 10 To ensure stability, the dishwasher must be fixed securely to the worktop (step 5). Two securing pieces are supplied for this purpose. ^ Push the dishwasher right back into the recess. Ensure that the drain hose, inlet hose and the electric ca- ble are laid to reach the connection point without any kinks.
- Page 11 ^ Use a TORX T20 screwdriver to ad- ^ Adjust the front screw feet manually just the rear screw feet to the re- or with a flat blade screwdriver. quired height. Now adjust the feet until the seal on Higher = turn clockwise the top of the dishwasher is right up Lower = turn anti-clockwise against the underside of the...
- Page 12 The weight of the door front will affect the functioning of the door The front of the dishwasher needs to be springs. After fitting it is essential for fitted with a base unit front to match the this to be checked out. See Step 6. kitchen furniture.
- Page 13 Dimension must be calculated and noted before attaching the fixing bracket. ^ Lay the door front down with the rear Dimension is the distance shown on side facing upwards. Draw a vertical the illustration between the drill hole in line down the middle of the door front the machine outer door panel and the rear to use as a guide line.
- Page 14 ^ If necessary pre-drill holes for the There are notches on the fixing bracket, marked a in the illustration. screws (Ø 2.5 mm, approx. 10 mm deep). ^ Lay the fixing bracket on the rear of ^ Screw the fixing bracket on securely. the door front, using dimension the distance from the bottom, and so Only one screw is required in each of...
- Page 15 ^ Hang the door front so that the lower lugs of the fixing bracket fit into the The door front is correctly fitted when: lower slits of the dishwasher outer – the lower lugs on the fixing bracket door panel, and draw slightly up- rest firmly in the lower slits of the wards.
- Page 16 ^ Close the dishwasher door. ^ Check the alignment of the door When fitted the door front can be ad- justed up to a maximum of 2 mm up- panel again. wards or downwards to match adjoining ^ If it is not correctly aligned you may unit fronts.
- Page 17 ^ Open the dishwasher door. The holes in the securing pieces must line up with the long holes in the worktop cover plate. If this is not the case, adjust the position of the dishwasher in the niche (ensure that the dishwasher is the same distance from the neighbouring kitchen units on the right and left hand sides and...
-
Page 18: Adjusting The Door Springs
If the the door front is too heavy for the door springs (i.e. the door falls open) then stronger springs should be fitted. Please contact your Miele dealer or the Miele Spare Parts Department for ad- ^ Adjust the door spring with a Torx vice. - Page 19 ^ Place the plinth facia directly in front of the kitchen run but do not attach. ^ Carefully open the dishwasher door. The plinth area of the dishwasher is normally covered with a plinth run If the door front comes into contact with matching the kitchen furniture.
- Page 20 All electrical work should be carried complete connection box and cable out only by a suitably qualified and by a Miele approved service techni- competent person, in strict accor- cian only. dance with national and local safety regulations.
- Page 21 The wires in the mains lead are col- oured in accordance with the following code: Green/yellow = earth Blue = neutral Brown = live If the colours of the wires in the mains lead of this appliance do not corre- spond with the coloured markings iden- tifying the terminals of your plug, pro- ceed as follows:...
- Page 22 (4 m), or a 1.5 m long flexible metal hose tested to with- stand pressure of 140 bar may be bought from the Miele Spare Parts Dept. – A stopcock with a 3/4 " male thread must be provided on site.
- Page 23 ^ Open the dishwasher door fully. – The machine drainage system is fit- ted with a non-return valve, which If the site drain connection is situated prevents dirty water from flowing lower than the guide path for the bot- back into the machine via the drain tom basket rollers in the open door the hose.
- Page 24 ... build the dishwasher into a kitchen which ...a separate plinth kit does not have a matching plinth run available in: white black ... adjust the height of the dishwasher to ...kit with extended machine feet between 87 cm and 92 cm (G 643 - G 663) or between 89 cm and 94 cm (G 843 - G 863)
- Page 25 Height 81.7 cm 83.7 cm (adjustable + 5.0 cm) (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm) Width 59.8 cm 59.8 cm Width of building in recess 60 cm 60 cm Depth 57 cm...
- Page 26 Height 81.7 cm 83.7 cm (adjustable + 5.0 cm) (adjustable + 5.0 cm) Height of building in recess 82 cm (+ 5.0 cm) 84 cm (+ 5.0 cm) Width 59.8 cm 59.8 cm Width of building in recess 60 cm 60 cm Depth 57 cm...
- Page 28 Alteration rights reserved (NovoPlus Vi60) / 1003 M.-Nr. 05 585 951 / V00 This paper consists of cellulose which has been bleached without the use of chlorine.