Miele HG01 Installation Instructions Manual
G 600 / g 800 series integrated dishwasher
Hide thumbs
Also See for HG01:
- Operating instructions manual (56 pages) ,
- Installation instructions manual (40 pages)
Related Manuals for Miele HG01
Summary of Contents for Miele HG01
-
Page 1: Installation Instructions
Installation instructions Integrated dishwasher To prevent accidents and machine damage, read these instructions installation or use. M.-Nr. 05 620 662... - Page 2 3. Install the slide skis ..........14 4. Install the dishwasher under the countertop ......15 5.
- Page 3 Installation, maintenance and repair work should be by a Miele authorized service technician. Work by unqualified persons could be a hazard and may void the warranty. This equipment is not designed for maritime use or for use in mobile installations such as caravans or aircraft.
- Page 4 When discarding an old dishwasher, unplug it from the power outlet, remove the door to the wash cabinet and cut off the power cord.
- Page 5 Toutefois, il peut être parfois possible de faire l’installation de ces applications sous certaines conditions. Veuillez contacter le Concessionnaire Miele le plus près de chez-vous ou le Département du service technique Miele pour leur don- ner vos exigences précises.
- Page 6 Avant l’installation, s’assurer que la tension et la fréquence énumérées sur la plaque signalétique correspon- dent à la source d’électricité de la rési- dence. Ces données doivent corres- pondre afin d’éviter de vous blesser et d’endommager l’appareil. Consulter un électricien qualifié si vous avez des doutes.
- Page 7 The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Old appliances may contain materials that can be recycled.
- Page 8 ^ Gently pull on the upper portion of the mounting bracket until the door latch releases (small arrow). ^ Grip the T shaped opening with a finger and pull the door open.
- Page 9 (845-864 mm) are not possible using the supplied legs. For this height range, or for heights greater than 34 " (886 mm), extended legs (part # 02 702 601) are necessary. Contact the Miele Technical Service Department for the appropriate legs. " - 34"...
- Page 10 Machine heights of 35" - 37" (889-940 mm) cannot be obtained using the supplied legs. For this height range, or for heights greater than 35" (889 mm), extended legs (part# 02 702 601) are necessary. Contact the Miele Technical Service Department for the appropriate legs.
- Page 11 A stainless steel steam deflector is supplied to protect the countertop from steam and condesation when the dishwasher is opened. If the countertop is made of Corian®, granite, marble or other solid, waterproof material, the steam deflector is not required.
- Page 12 For rounded countertops it may be necessary to pull the steam deflector closer to the counter’s edge so the optic reflector will be visible.
- Page 13 The steam deflector is not required for countertops made of solid, waterproof material. But it is needed for determining the correct position of the optic indicator reflector. ^ Remove the black plastic reflector holder and the tape holding it in place from the steam deflector.
- Page 14 ^ First, adjust the height of the legs so that the top of the dishwasher is roughly " (3 mm) below the countertop.
- Page 15 The left side of the optic indicator reflector and the optic indicator must align. The drain hose connection at the rear of the dishwasher can be turned to allow the hose to be angled to the right or left. ^ Exercise care when sliding the dishwasher in or out, to prevent damaging the power cord or hoses.
-
Page 16: Level Legs
^ Tipping the machine slightly backwards, if posssible will make adjusting the front legs easier. Make sure the machine is level when adjustments are complete. The dishwasher should be raised until it just touches the underside of the countertop. - Page 17 A custom door panel must be installed on the dishwasher before it can be safely operated. A single large panel or a two piece panel separated at the drawer line can be used. Panel size is determined in the following manner:...
- Page 18 The door panel is attached to the dishwasher using the mounting bracket that comes secured to the front of the unit. To remove the bracket: ^ Open the door 2 - 4" (5 - 10 cm). ^ Loosen the bracket retaining screw (black arrow) located on each side of the machine door.
- Page 19 ^ Make sure the dishwasher is level. ^ Measure the distance round hole in the machine outer door panel (shown in inset) and the lower edge of the adjoining cabinet door. ^ Place the door panel on a flat surface, good side face down, being careful not to scratch the surface.
- Page 20 ^ Double check the location of the bracket before mounting the panel to the dishwasher. The door handle must be installed on the panel before it is attached to the machine. It should be located in the center of the panel at a height that will match the surrounding drawer handles.
- Page 21 ^ Open the door 2 - 4" (5 - 10 cm). ^ Place the lower mounting clips into the slots of the dishwasher door as shown in the illustration. ^ Seat the U shaped slots of the upper bracket onto their respective locator pins.
- Page 22 ^ The panel can be raised or lowered by turning the lower screw on each side of the dishwasher door. To raise the panel turn clockwise. To lower the panel turn counterclockwise.
- Page 23 Do not drill any additional holes through the wash cabinet. If in doubt on how to secure the dishwasher, please call Miele’s Technical Service Department.
- Page 24 For openings exactly 23 wide: ^ Open the dishwasher door and remove the caps covering the mounting holes on the outer edge of the wash cabinet. ^ Fasten the dishwasher to the adjacent cabinets using the supplied screws and bushings. A bushing...
- Page 25 – turn counterclockwise to decrease the tension. If the door springs can not be adjusted enough (the door falls), the custom door panel is too heavy. Call your Miele dealer or the Technical Service Department for advice on stronger door springs.
- Page 26 An air gap is built into the water inlet system to prevent potable water from mixing with waste water. The dishwasher can heat its own water to the temperatures required by the wash program. This allows the option of connecting the machine to either a hot or cold water source.
- Page 27 /adapter assembly. WARNING - Elcetrical Hazard Do not cut the intake hose. If the hose is cut, the dishwasher will not work. There will be a water leak and you could be injured. If the hose is too long, coil it neatly and place it behind the machine.
- Page 28 – A 5 ft. long (1.5 m) flexible drain hose with an internal diameter of (22 mm). Drain hose extensions can be ordered from Miele’s Technical Service Department. – A built-in swivel connector allowing the drain hose to be routed in any direction.
- Page 29 ^ Cut off the vent cap located at the right rear of the triple filter system, as illustrated. Since all Miele dishwashers are equipped with an odor trap and non- return valve, the drain hose can be connected directly to the drain pipe as illustrated.
- Page 30 The dishwasher comes equipped with a 4 ft (1.2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle.
- Page 31 The power outlet for the appliance must be installed within a cabinet, on a wall adjacent to the undercounter space in which the dishwasher is located. An opening through the partition between the compartments of 1 can be made to allow the plug to pass through.
- Page 32 Once the dishwasher is level and secured it should be tested. ^ Remove all packing and literature from inside the unit. The yellow Child Safety Lock key hung on the upper basket must be removed before operating the dishwasher. If not removed, the key could become lodged in the circulation pump.
- Page 33 ( ) is at least " (19 mm). If the door panel hits the toekick when the dishwasher door is opened, the toekick must be cut shorter or recessed deeper. If a decorative or flush mount toekick is...
- Page 34 ^ Insert the mounting bracket with the flange pointing toward the center of the machine. ^ Push the mounting brackets in as far as possible by releasing the tension on the spring clip (see illustration). ^ Insert the mounting bracket with the flange pointing toward the outside of the machine.
- Page 35 The included toekick will fit without modification if the machine is set to its maximum height and the toekick is recessed as far as possible (4"/10 cm). If the machine height is less than maximum, or if the toekick is not recessed 4"...
- Page 36 ^ Carefully open the dishwasher door until it hits the toekick. ^ Using the front lower edge of the door panel as a guide, draw a line across the toekick. ^ Unscrew and remove the toekick. ^ If one of the cutting lines is close to...
- Page 40 Alterations rights reserved / MVi60 3304 M.-Nr. 05 620 662 / 01 This bio-friendly paper was bleached without the use of chlorine.