Ec Declaration Of Conformity - Flymo Sabre Trim Owner's Manual

Flymo sabre trim owner's manual
Hide thumbs Also See for Sabre Trim:
Table of Contents

Advertisement

If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna Outdoor Products,
through its Authorised Service Repairers will effect the repair or
replacement to the customer free of charge providing:
(a)
The fault is reported directly to the Authorised Repairer.
(b)
Proof of purchase is provided.
(c)
The fault is not caused by misuse, neglect or faulty adjust-
ment by the user.
(d)
The failure has not occurred through fair wear and tear.
(e)
The machine has not been serviced or repaired, taken apart
or tampered with by any person not authorised by
Husqvarna Outdoor Products.
(f)
The machine has not been used for hire.
(g)
The machine is owned by the original purchaser.
(h)
The machine has not been used outside of the country for
which it was specified.
(i)
The machine has not been used commercially.
*
This guarantee is additional to, and in no way diminishes
the customers statutory rights.
I, the undersigned M. Bowden of Husqvarna
Outdoor Products, Aycliffe Industrial Park, NEW-
TON AYCLIFFE, Co. Durham. DL5 6UP. Certify
that the Product:-
Battery Lawn Trimmer
Category........
Husqvarna Outdoor
Make..............
Products
Conforms to the specifications of Directive 2000/14/EEC
Cutting Line
Type of Cutting Device....
See Product Rating Label
Identification of Series......
Conformity Assesment Procedure....ANNEX VI
Intertek., Cleeve Road, Leatherhead,
Notified Body....................
Surrey. KT22 7SB England
98/37/EEC, 89/336/EEC
Other Directives:-.............
EN786, EN60335-1, EN60335-2-29, EN55022,
& applicable standards:-
EN61000-4-2, EN61000-4-3, EN55014-1, EN61000-3-2, EN61000-3-3,
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
5107422-01
Guarantee & Guarantee Policy

EC Declaration of Conformity

I, the undersigned M. Bowden of Husqvarna
Outdoor Products, Aycliffe Industrial Park, NEW-
TON AYCLIFFE, Co. Durham. DL5 6UP Certify
that a sample of the above product has been
tested using directive 81/1051/EEC as a guide.
The maximum A-weighted sound pressure level
recorded at operator position under free field semi
anechoic chamber conditions was :-
Husqvarna Outdoor Products
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - (00) 44 1325 300303 Fax - (00) 44 1325 310339
UK Customer Helpline - 01325 300303 Fax - 01325 310339
Failures due to the following are not covered, therefore it is important that
you read the instructions contained in this Operator's Manual and under-
stand how to operate and maintain your machine:
Failures not covered by guarantee
*
Replacing Nylon Line.
*
Failures as a result of not reporting an initial fault.
*
Failures as a result of sudden impact.
*
Failures as a result of not using the product in accordance
with the instructions and recommendations contained in this
Operator's Manual.
*
Machines used for hire are not covered by this guarantee.
*
The following items listed are considered as wearing parts and their life
is dependent on regular maintenance and are, therefore not normally
subject to a valid warranty claim: Nylon Line., Spool & Line
Caution!
*
Husqvarna Outdoor Products does not accept liability under the
warranty for defects caused in whole or part, directly or indirectly
by the fitting of replacement parts or additional parts that are not
either manufactured or approved by Husqvarna Outdoor
Products, or by the machine having been modified in any way.
I, the undersigned M. Bowden of Husqvarna
Outdoor Products, Aycliffe Industrial Park,
NEWTON AYCLIFFE, Co. Durham. DL5 6UP
Certify that a sample of the above product has
been tested using ISO 5349 as a guide. The
maximum weighted root mean square value of
vibration recorded at operator's hand position
was:-
Type ................................................................. GTC24A
Width of Cut ..................................................... 25 cm
Speed of Rotation of Cutting Device ............... 10,000 RPM
Guaranteed sound power level ....................... 93 dB(A)
Measured Sound Power Level ........................ 92 dB(A)
Level ................................................................ 75.6 dB(A)
Value ................................................................ 1.87 m/s
Weight ............................................................. 6.89 kg
Newton Aycliffe, 14/05/2005
M. Bowden,
Research & Development Director
2

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Sabre trim gtc24a

Table of Contents