Summary of Contents for ZyXEL Communications Prestige 650M
Page 1
Prestige 650M ADSL Bridge User's Guide Version 3.40 March 2003...
Page 2
Trademarks ZyNOS (ZyXEL Network Operating System) is a registered trademark of ZyXEL Communications, Inc. Other trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners.
Prestige 650M ADSL Bridge Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operations.
Prestige 650M ADSL Bridge ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and...
Prestige 650M ADSL Bridge Customer Support Please have the following information ready when you contact customer support. • Product model and serial number. • Information in Menu 24.2.1 – System Information. • Warranty Information. • Date that you received your device.
List of Tables..........................xii Preface ............................xiii What is DSL?..........................xv Chapter 1 Getting To Know Your Prestige....................1-1 Prestige 650M ADSL Bridge .....................1-1 Features of the Prestige....................1-1 Applications for the Prestige .....................1-3 Chapter 2 Hardware Installation and Initial Setup .................. 2-1 Front Panel LEDs of the Prestige ..................2-1...
Page 9
Prestige 650M ADSL Bridge Problems Accessing the Internet ..................9-3 Appendix A Power Adapter Specifications....................A Appendix B Virtual Circuit Topology......................C Appendix C Setting up Your Computer’s IP Address ..................D Index.................................O Table of Contents...
Prestige 650M ADSL Bridge List of Figures Figure 1-1 Internet Access Application......................1-3 Figure 1-2 LAN-to-LAN Application......................1-4 Figure 2-1 Prestige Front Panel ........................2-1 Figure 2-2 Prestige Rear Panel and Connections....................2-2 Figure 2-3 ISDN Splitter Installation......................2-4 Figure 3-1 Password Screen ...........................3-1 Figure 3-2 Prestige SMT Menu Overview......................3-2 Figure 3-3 SMT Main Menu...........................3-4...
Page 11
Prestige 650M ADSL Bridge Figure 7-5 Menu 24.2.2 – System Maintenance – Change Console Port Speed ..........7-5 Figure 7-6 Menu 24.4 – System Maintenance – Diagnostic ................7-6 Figure 7-7 Command Mode in Menu 24......................7-7 Figure 7-8 Valid Commands .......................... 7-7 Figure 8-1 Telnet in Menu 24.5........................
Page 12
Prestige 650M ADSL Bridge List of Tables Table 1 P650M Models ..........................xiii Table 2-1 Front Panel LED Description....................... 2-1 Table 3-1 Main Menu Commands........................ 3-3 Table 3-2 Main Menu Summary ........................3-4 Table 3-3 General Setup Menu Fields......................3-6 Table 3-4 TCP/IP Ethernet Setup Menu Fields ....................
Analog model for ADSL over ISDN in Germany. RJ-45 connector. The Prestige 650M is an ADSL bridge used for Internet/LAN access via POTS or ISDN line. The Prestige can run maximum upstream transmission rates of up to 832Kbps and maximum downstream transmission rates of 8Mbps.
• The Prestige 650M ADSL Bridge may be referred to as the Prestige in this User’s Guide when referring to all three models and to P650M-31, P650M-33 or P650M-37 when referring to the specific model.
Prestige 650M ADSL Bridge What is DSL? DSL (Digital Subscriber Line) enhances the data capacity of the existing twisted-pair wire that runs between the local telephone company switching offices and most homes and offices. While the wire itself can handle higher frequencies, the telephone switching equipment is designed to cut off signals above 4,000 Hz to filter noise off the voice line, but now everybody is searching for ways to get more bandwidth to improve access to the Web - hence DSL technologies.
Prestige 650M ADSL Bridge Chapter 1 Getting To Know Your Prestige This chapter describes the key features and applications of your Prestige Prestige 650M ADSL Bridge Your Prestige integrates a high-speed 10/100Mbps auto-negotiating LAN interface and one high-speed DSL port into a single package. The Prestige is ideal for high-speed Internet browsing and making LAN-to-LAN connections to remote networks.
Prestige 650M ADSL Bridge • Diagnostics Capabilities The Prestige can perform self-diagnostic tests. These tests check the integrity of the following circuitry: FLASH memory DSL circuitry LAN port Filters The Prestige's packet filtering functions allows added network security and management.
Prestige 650M ADSL Bridge 1.3.2 LAN to LAN Application You can use the Prestige to connect two geogr ly dispersed networks over the DSL line. A typical aphical LAN-to-LAN application for your Prestige is shown as follows. Figure 1-2 LAN-to-LAN Application...
Prestige 650M ADSL Bridge Chapter 2 Hardware Installation and Initial Setup This chapter describes the physical features of the Prestige and how to make cable connections Front Panel LEDs of the Prestige The LEDs on the front panel indicate the operational status of your Prestige...
Prestige 650M ADSL Bridge Table 2-1 Front Panel LED Description COLOR STATUS DESCRIPTION Orange The Prestige has a successful 100Mb Ethernet connection. 100M Blinking The Prestige is sending/receiving data. The Prestige does not have 100Mb Ethernet connection. Green The Prestige is linked successfully to a DSLAM.
Prestige 650M ADSL Bridge Connect the Prestige to the wall jack using the included DSL cable. For the P650M-33 and P650M-37 models, connect an ISDN splitter between the wall jack and your telephone(s) and computer(s). 2.2.2 LAN 10/100M Port Ethernet 10Base-T/100Base-T networks use Shielded Twisted Pair (STP) cable. This port is auto-sensing which means Use a crossover cable or a straight-through Ethernet cable to connect your Prestige to a computer or an external hub.
Prestige 650M ADSL Bridge Step 5. Continue to hold the RESET button for about 30 seconds. The Prestige restarts. Step 6. Release the RESET button and wait for the Prestige to finish restarting. Connecting an ISDN Splitter This section is relevant for P650M-33 and P650M-37 models only! This device keeps the ISDN and DSL signals separated, giving them the capability to provide simultaneous Internet access and ISDN service on the same line.
Prestige 650M ADSL Bridge Turning On Your Prestige At this point, you should have connected the DSL, LAN and Power ports to the appropriate devices. Make sure the power adapter is plugged into an appropriate power source. Press the power switch in. The Power LED turns on. The SYS LED blinks and turns steady on. The SYS LED turns red if power is too low.
Prestige 650M ADSL Bridge Chapter 3 Initial Setup This chapter introduces the SMT and shows you how to configure SMT menus 1 and 3. Configure your Prestige using the SMT (System Management Terminal) via LAN or WAN using Telnet. 3.1.1 Connect to Your Prestige Using Telnet The following procedure details how to telnet into your Prestige.
Prestige 650M ADSL Bridge Figure 3-2 Prestige SMT Menu Overview Navigating the SMT Interface The SMT (System Management Terminal) is the interface that you use to configure your Prestige. Several operations that you should be familiar with before you attempt to modify the configuration are listed in the table below.
Prestige 650M ADSL Bridge Table 3-1 Main Menu Commands OPERATION KEYSTROKE DESCRIPTION Move down to [ENTER] To move forward to a submenu, type in the number of the desired another menu submenu and press [ENTER]. Move up to a [ESC] Press [ESC] to move back to the previous menu.
Prestige 650M ADSL Bridge Step 2. Type your existing system password in the Old Password field, for example “1234”, and press [ENTER]. Menu 23 – System Password Old Password= **** New Password= ? Retype to confirm= ? Enter here to CONFIRM or ESC to CANCEL: Figure 3-4 Menu 23 –...
Prestige 650M ADSL Bridge 2. Use the RESET button on the rear panel of the Prestige (see section 2.2.5). SMT Menu 1: General Setup Menu 1 – General Setup contains administrative and system-related information. To enter menu 1 and fill in the required information, follow these steps: Step 1.
Prestige 650M ADSL Bridge 3.6.1 LANs, WANs and the Prestige The actual physical connection determines whether the Prestige ports are LAN or WAN ports. There are two separate IP networks, one inside, the LAN network; the other outside: the WAN network as shown next: Figure 3-6 LAN &...
Prestige 650M ADSL Bridge SMT Menu 3: TCP/IP LAN Setup The Ethernet parameters of the Prestige are preset in the factory with the following values: IP address of 192.168.1.1 with subnet mask of 255.255.255.0 (24 bits). Use menu 3.2 to configure the IP address of your Prestige. You need to do this to be able to manage yopur Prestige.
Prestige 650M ADSL Bridge Chapter 4 Internet Access This chapter shows you how to configure your Prestige for Internet access Introduction Menu 4 allows you to enter your Internet Access information in one screen. Menu 4 is actually a simplified setup for one of the remote nodes that you can access in menu 11.
Prestige 650M ADSL Bridge Multiplexing There are two conventions to identify what protocols the virtual circuit (VC) is carrying. Be sure to use the multiplexing method required by your ISP. 4.3.1 VC–based Multiplexing In this case, by prior mutual agreement, each protocol is assigned to a specific virtual circuit, for example, VC1 carries IP, etc.
Prestige 650M ADSL Bridge Scenario 1. One VC, Multiple Protocols PPPoA (RFC-2364) encapsulation with VC-based multiplexing is the best combination because no extra protocol identifying headers are needed. The PPPoA protocol already contains this information. Scenario 2. One VC, One Protocol (IP) Selecting RFC 1483 encapsulation with VC-based multiplexing requires the least amount of overhead (0 octets).
Prestige 650M ADSL Bridge Figure 4-1 Example of Traffic Shaping If the PCR is set to the default of “0”, the system will assign a maximum value that correlates to your upstream line rate. Internet Access Configuration From the main menu, enter 4 to display Menu 4–Internet Access Setup, as shown next.
Prestige 650M ADSL Bridge The following table contains instructions on how to configure your Prestige for Internet access. Table 4-2 Internet Access Setup Menu Fields FIELD DESCRIPTION EXAMPLE ISP’s Name Enter the name of your Internet Service Provider. This ChangeMe information is for identification purposes only.
Prestige 650M ADSL Bridge Chapter 5 Remote Node Configuration This chapter shows you how to set up a remote node. Remote Node Setup A remote node is required for placing calls to a remote gateway. A remote node represents both the remote gateway and the network behind it across a WAN connection.
Page 43
Prestige 650M ADSL Bridge Table 5-1 Remote Node Profile Menu Fields FIELD DESCRIPTION EXAMPLE My Login Type the login name assigned by your ISP when the Prestige calls this remote node. My Password Type the password assigned by your ISP when the Prestige calls this remote node.
Page 44
Prestige 650M ADSL Bridge Table 5-1 Remote Node Profile Menu Fields FIELD DESCRIPTION EXAMPLE (SCR)= 0 source that can be sent at the peak rate, and a parameter for burst- type traffic. Type the SCR; it must be less than the PCR.
Prestige 650M ADSL Bridge Chapter 6 Filter Set Configuration This chapter shows you how to create and apply filters. About Filtering Your Prestige uses filters to decide whether or not to allow passage of data packets. Data filtering examines the data to determine if the packet should be allowed to pass. Data filters are divided into incoming and outgoing filters, depending on the direction of the packet relative to a port.
Prestige 650M ADSL Bridge Start Packet intoFilter Fetch First Filter Set Filter Set Fetch Next Fetch First Filter Set Filter Rule Fetch Next Filter Rule Next filter Next Filter Set Rule Active? Available? Available? Execute Filter Rule Check Next Rule...
Prestige 650M ADSL Bridge Configuring a Filter Set To configure a filter set, follow the steps shown next. Step 1. Enter 21 in the main menu to display Menu 21-Filter Set Configuration Menu 21 - Filter Set Configuration Filter Filter...
Prestige 650M ADSL Bridge 6.2.1 Filter Rules Summary Menus The following tables briefly describe the abbreviations used in menus 21.1 and 21.2. Table 6-1 Abbreviations Used in the Filter Rules Summary Menu FIELD DESCRIPTION The filter rule number: 1 to 6.
Prestige 650M ADSL Bridge the data portion before comparing the result against the Value to determine a match. The Mask and Value are specified in hexadecimal numbers. Two hexadecimal digits represent a byte, so if the length is 4, the value in either field will take 8 digits, e.g., FFFFFFFF.
Prestige 650M ADSL Bridge Table 6-3 Menu 21.5.1 Generic Filter Rule Fields – FIELD DESCRIPTION EXAMPLE Mask Type the mask (in Hexadecimal) to apply to the data portion before comparison. Value Type the value (in Hexadecimal) to compare with the data portion.
Prestige 650M ADSL Bridge Step 6. When you press [ENTER] to confirm, you will see the next screen. Note that there is only one filter rule in this set. Menu 21.3 - Filter Rules Summary # A Type Filter Rules...
Prestige 650M ADSL Bridge Chapter 7 System Information and Diagnosis This chapter covers the information and diagnostic tools in SMT menus 24.1 to 24.4 and 24.8. Introduction These menus display system status, port status and use of diagnostic tools when problems occur and an introduction to the command interface.
Prestige 650M ADSL Bridge Menu 24.1 - System Maintenance - Status 01:30:36 Thu. Oct. 30, 2002 Node-Lnk Status TxPkts RxPkts Errors Tx B/s Rx B/s Up Time 1-1483 0:00:00 0:00:00 0:00:00 0:00:00 0:00:00 0:00:00 0:00:00 0:00:00 My WAN IP (from ISP): 0.0.0.0...
Prestige 650M ADSL Bridge Table 7-1 System Maintenance – Status Menu Fields FIELD DESCRIPTION Tx Pkts This is the number of transmitted packets to the LAN. Rx Pkts This is the number of received packets from the LAN. CPU Load This specifies the percentage of CPU utilization.
This field shows the kind of routing used by the Prestige. ZyNOS F/W Version This field displays the ZyNOS (ZyXEL Network Operating System) system firmware version. ZyNOS is a registered trademark of ZyXEL Communications Corporation. ADSL Chipset Vendor This is the chipset used in the Prestige.
Prestige 650M ADSL Bridge 7.3.2 Console Port Speed You can set up different port speeds for the console port through Menu 24.2.2 – System Maintenance – Console Port Speed. Your Prestige supports 9600 (default), 19200, 38400 and 57600bps console port speeds.
Prestige 650M ADSL Bridge Menu 24.4 - System Maintenance – Diagnostic xDSL System Reset xDSL 21. Reboot System 22. Command Mode TCP/IP 12. Ping Host Enter Menu Selection Number: Host IP Address= N/A Figure 7-6 Menu 24.4 – System Maintenance – Diagnostic The following table describes the diagnostic tests available in menu 24.4 for and the connections.
Prestige 650M ADSL Bridge Chapter 8 Firmware and Configuration File Maintenance This chapter shows you how to back up and restore your configuration file as well as upload new firmware and a new configuration file. Identifying Your Product Look at the bottom of your product for a label that contains the product name. If you’re looking for new firmware, you should first look for firmware of this exact name, including the suffix, for example P650M- If you’re unsure of the name or can’t find the exact firmware name, please contact customer support or your...
Prestige 650M ADSL Bridge network or FTP site and so the name (but not the extension) may vary. After uploading new firmware, see the ZyNOS F/W Version field in Menu 24.2.1 – System Maintenance – Information to confirm that you have uploaded the correct firmware version.
Prestige 650M ADSL Bridge Menu 24.5 - Backup Configuration To transfer the configuration file to your computer, follow the procedure below: 1. Launch the FTP client on your computer. 2. Type "open" and the IP address of your system. Then type "root" and SMT password as requested.
Prestige 650M ADSL Bridge 331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> get rom-0 zyxel.rom 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK ftp: 16384 bytes sent in 1.10Seconds 297.89Kbytes/sec.
Prestige 650M ADSL Bridge Step 1. Use Telnet from your computer to connect to the Prestige and log in. Because TFTP does not have any security checks, the Prestige records the IP address of the telnet client and accepts TFTP requests only from this address.
Prestige 650M ADSL Bridge Table 8-3 General Commands for GUI-based TFTP Clients COMMAND DESCRIPTION Remote File This is the filename on the Prestige. The filename for the firmware is “ras” and for the configuration file, is “rom-0”. Binary Transfer the file in binary mode.
Prestige 650M ADSL Bridge Menu 24.6 - System Maintenance - Restore Configuration To transfer the firmware and configuration file to your workstation, follow the procedure below: 1. Launch the FTP client on your computer. 2. Type "open" and the IP address of your system. Then type "root" and SMT password as requested.
Prestige 650M ADSL Bridge Uploading Firmware and Configuration Files This section shows you how to upload firmware and configuration files. You can upload configuration files by following the procedure in the previous Restore Configuration section or by following the instructions in Menu 24.7.2 - System Maintenance - Upload System Configuration File.
Prestige 650M ADSL Bridge Menu 24.7.2 - System Maintenance - Upload System Configuration File To upload the system configuration file, follow the procedure below: 1. Launch the FTP client on your computer. 2. Type "open" and the IP address of your system. Then type "root" and SMT password as requested.
Prestige 650M ADSL Bridge 331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> put firmware.bin ras 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK ftp: 1103936 bytes sent in 1.10Seconds 297.89Kbytes/sec.
Page 71
Prestige 650M ADSL Bridge tftp [-i] host put firmware.bin ras where “i” specifies binary image transfer mode (use this mode when transferring binary files), “host” is the Prestige’s IP address and “put” transfers the file source on the computer (firmware.bin – name of the firmware on the computer) to the file destination on the remote host (ras - name of the firmware on the Prestige).
Prestige 650M ADSL Bridge Chapter 9 Troubleshooting This chapter covers potential problems and possible corresponding remedies. Problems Starting the Prestige Table 9-1 Problems Starting the Prestige PROBLEM CORRECTIVE ACTION No LEDs are on Make sure that the Prestige’s power adapter is connected to the Prestige and when the Prestige plugged in to an appropriate power source.
Prestige 650M ADSL Bridge Problems Connecting to the LAN Table 9-3 Problems Connecting with the LAN PROBLEM CORRECTIVE ACTION Cannot ping Check the LAN LEDs on the front panel. The LAN LED should be on if a computer is any computer connected.
Prestige 650M ADSL Bridge Problems Accessing the SMT Menu Table 9-5 Problems Accessing SMT Menus PROBLEM CORRECTIVE ACTION I cannot access The default SMT password is “1234”. If you have changed the password and have the SMT menu. now forgotten it, you will need to upload the default configuration file.
Prestige 650M ADSL Bridge Appendix A Power Adapter Specifications NORTH AMERICA PLUG STANDARDS AC Power Adapter model DV-121AACS Input power AC120Volts/60Hz/23W max. Output power AC12Volts/1.0A Power consumption Safety standards UL, CUL (UL 1310, CSA C22.2 No.223) NORTH AMERICA PLUG STANDARDS...
Page 78
Prestige 650M ADSL Bridge EUROPEAN PLUG STANDARDS AC Power Adapter model DV-121AACCP-5716 Input power AC230Volts/50Hz/100mA Output power AC12Volts/1.0A Power consumption Safety standards TUV-GS, CE (EN 60950) UNITED KINGDOM PLUG STANDARDS AC Power Adapter model AA-121AD Input power AC230Volts/50Hz/140mA Output power AC12Volts/1.0A...
Prestige 650M ADSL Bridge Appendix B Virtual Circuit Topology ATM is a connection-oriented technology, meaning that it sets up virtual circuits over which end systems communicate. The terminology for virtual circuits is as follows: • Virtual Channel Logical connections between ATM switches •...
Prestige 650M ADSL Bridge Appendix C Setting up Your Computer’s IP Address All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Windows 95/98/Me/NT/2000/XP, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/IP on your computer.
Page 81
Prestige 650M ADSL Bridge The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks. If you need the adapter: In the Network window, click Add. Select Adapter and then click Add.
Page 82
Prestige 650M ADSL Bridge Click the IP Address tab. -If your IP address is dynamic, select Obtain an IP address automatically. -If you have a static IP address, select Specify an IP address and type your information into the IP Address and Subnet Mask fields.
Page 83
Prestige 650M ADSL Bridge Click the Gateway tab. -If you do not know your gateway’s IP address, remove previously installed gateways. -If you have a gateway IP address, type it in the New gateway field and click Add. Click OK to save and close the TCP/IP Properties window.
Page 84
Prestige 650M ADSL Bridge For Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control Panel. For Windows XP, click Network Right-click Local Area Connection and Connections. For Windows 2000/NT, click then click Properties. Network and Dial-up Connections.
Page 85
Prestige 650M ADSL Bridge Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties. The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP). -If you have a dynamic IP address click Obtain an IP address automatically.
Page 86
Prestige 650M ADSL Bridge -If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK. Do one or more of the following if you want to configure additional IP addresses: -In the IP Settings tab, in IP addresses, click Add.
Page 87
Prestige 650M ADSL Bridge In the Internet Protocol TCP/IP Properties window (the General tab in Windows XP): -Click Obtain DNS server address automatically if you do not know your DNS server IP address(es). -If you know your DNS server IP address(es),...
Page 88
Prestige 650M ADSL Bridge Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel. Select Ethernet built-in from the Connect via list. For dynamically assigned settings, select Using DHCP Server from the Configure: list. Setting up Your Computer’s IP Address...
Prestige 650M ADSL Bridge For statically assigned settings, do the following: -From the Configure box, select Manually. -Type your IP address in the IP Address box. -Type your subnet mask in the Subnet mask box. -Type the IP address of your Prestige in the Router address box.
Page 90
Prestige 650M ADSL Bridge Click Network in the icon bar. - Select Automatic from the Location list. - Select Built-in Ethernet from the Show list. - Click the TCP/IP tab. For dynamically assigned settings, select Using DHCP from the Configure list.