Roland DP990F Implementation page 31

● 020a: Flanger→Delay
This effect connects a flanger and a delay in series.
No Parameter Value
1 Flanger Pre Delay 0-125
2 Flanger Rate Mode 0-1
3 Flanger Rate 1-127
4 Flanger Rate 0-21
5 Flanger Depth 0-127
6 Flanger Feedback 0-98
7 Flanger Balance #1 0-100
8 Delay Mode 0-1
9 Delay Time 0-127
10 Delay Time 0-21
11 Delay Feedback 49-89
12 Delay HF Damp 0-17
13 Delay Balance #2 0-100D
14 Level 0-127
● 020b: Chorus→Flanger
This effect connects a chorus and a flanger in series.
No Parameter Value
1 Chorus Pre Delay 0-125
2 Chorus Rate Mode 0-1
3 Chorus Rate 1-127
4 Chorus Rate 0-21
5 Chorus Depth 0-127
6 Chorus Balance #1 0-100
7 Flanger Pre Delay 0-125
8 Flanger Rate Mode 0-1
9 Flanger Rate 1-127
10 Flanger Rate 0-21
Description
Adjusts the delay time from when
0.0-100.0 ms the direct sound begins until the
flanger sound is heard.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
0.05-10.00 Hz Frequency of modulation (Hz)
note Frequency of modulation (note)
0-127 Depth of modulation
Adjusts the proportion of the
flanger sound that is fed back into
-98 - +98%
the effect. Negative (-) settings will
invert the phase.
Volume balance between the direct
D100:0W -
sound (D) and the flanger sound
D0:100W
(W)
When this is set to "note," the
ms, note effect is synchronized with the
tempo.
Adjusts the delay time from the
0-2540 ms direct sound until the delay sound
is heard. (Hz)
Adjusts the delay time from the
note direct sound until the delay sound
is heard. (note)
Adjusts the proportion of the delay
0 - +80% sound that is fed back into the
effect.
Adjusts the frequency above which
sound fed back to the effect will be
200-8000 Hz,
cut. If you do not want to cut the
Bypass
high frequencies, set this
parameter to Bypass.
Adjusts the volume balance
between the sound that is sent
100:0W -
through the delay (W) and the
D0:100W
sound that is not sent through the
delay (D).
0-127 Output Level
Description
Adjusts the delay time from the
0.0-100.0 ms direct sound until the chorus
sound is heard.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
Modulation frequency of the
0.05-10.00 Hz
chorus effect (Hz)
Modulation frequency of the
note
chorus effect (note)
Modulation depth of the chorus
0-127
effect
Volume balance between the direct
D100:0W -
sound (D) and the chorus sound
D0:100W
(W)
Adjusts the delay time from when
0.0 - 100.0 ms the direct sound begins until the
flanger sound is heard.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
Modulation frequency of the
0.05-10.00 Hz
flanger effect (Hz)
Modulation frequency of the
note
flanger effect (note)
11 Flanger Depth 0-127
12 Flanger Feedback 0-98
13 Flanger Balance #2 0-100
14 Level 0-127
● 0040: Damper Resonance
On an acoustic piano, holding down the damper pedal allows other strings to
resonate in sympathy with the notes you play, creating rich and spacious
resonances. This effect simulates these damper resonances.
No Parameter Value
1 Depth #1 0-127
2 Damper 0-127
3 Pre LPF 1-32
4 Pre HPF 0-31
5 Peaking Freq 0-16
6 Peaking Gain 0-30
7 Peaking Q 0-4
8 HF Damp Freq 1-32
9 LF Damp Freq 0-31
11 Level 0-127
12 P-Sft Amount 0-127
13 P-Sft Level 0-127
14 P-Sft LPF 1-32
15 P-Sft HPF 0-31
16 P-Sft to Rev 0-127
17 Damper Offset #2 0-64
31
Modulation depth of the flanger
0-127
effect
Adjusts the proportion of the
flanger sound that is fed back into
-98 - +98%
the effect. Negative (-) settings will
invert the phase.
Adjusts the volume balance
between the sound that is sent
D100:0W -
through the flanger (W) and the
D0:100W
sound that is not sent through the
flanger (D).
0-127 Output Level
Description
0-127 Depth of the effect
Depth to which the damper pedal is
0-127 pressed (controls the resonant
sound)
Frequency of the filter that cuts the
16-15000 Hz,
high-frequency content of the input
Bypass
sound (Bypass: no cut)
Frequency of the filter that cuts the
Bypass,
low-frequency content of the input
16-15000 Hz
sound (Bypass: no cut)
Frequency of the filter that
200-8000 Hz boosts/cuts a specific frequency
region of the input sound
Amount of boost/cut produced by
-15 - +15 dB the filter at the specified frequency
region of the input sound
Width of the frequency region
0.5, 1.0, 2.0, boosted/cut by the `Peaking Gain'
4.0, 8.0 parameter (larger values make the
region narrower)
Frequency at which the high-
16-15000 Hz,
frequency content of the resonant
Bypass
sound will be cut (Bypass: no cut)
Frequency at which the
Bypass, low-frequency content of the
16-15000 Hz resonant sound will be cut (Bypass:
no cut)
0-127 Output Level
0-127 Amount of resonance
Volume level of the resonant
0-127
component
Basic frequency at which the filter
16-15000 Hz, cuts the high-frequency portion of
Bypass the resonant component (Bypass:
no cut)
Basic frequency at which the filter
Bypass, cuts the low-frequency portion of
16-15000 Hz the resonant component (Bypass:
no cut)
Volume of additional resonance
0-127
added to resonant component
Volume of additional slight
0-64 resonance when the damper pedal
is not pressed