Table of Contents
Advertisement
3
Select "ONCE", "DAILY" (Mon-Fri), or "WEEKLY".
Then press [B] to go to next step.
or
4
Select the desired date.
Then press [B] to go to next step.
or
or
• You can set a program one year in advance.
5
Select the desired start time (hour)
Then press [B] to go to next step.
or
or
6
Select "AM" or "PM".
Then press [B] to go to next step.
or
Repeat the procedure in steps 5 and 6 to set the end time.
7
Select "L1" or "L2".
8
Then press [B] to go to next step.
or
Hints for OTR and Timer Recording
• If a tape is not in the unit or does not have the record tab,
be performed. Please insert a recordable tape.
• When Timer Recordings are set,
recording, press [T-SET] so that
After an OTR or a Timer Recording has been set, this unit operates as follows:
• If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape. Press [T-SET] on the remote
control or [STOP/EJECT C A] on the unit, then press [VCR] to activate the VCR function again.
• Once the unit turns to the timer standby mode, no VCR functions are available until [T-SET] is pressed.
• To cancel the timer standby mode, press [T-SET] on the remote control or [STOP/EJECT C A] on the unit, then press [VCR]
to activate the VCR function again.
When an OTR or a Timer Recording is completed...
• If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically, and
indicator on the front panel lights to indicate the unit is in the timer standby mode.
•
indicator on the front panel flashes if there are no more Timer Recordings on standby.
• If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR functions will be
unavailable. All the DVD functions are available during OTR, timer standby mode and Timer Recording.
• Press [STOP/EJECT C A] on the front panel or [T-SET] on the remote control to use the VCR when the unit is off.
• Press [OUTPUT] on the front panel or [VCR] on the remote control to use the VCR when the unit is on. In case Timer
Recording is in standby mode, press [STOP/EJECT C A] on the front panel or [T-SET] on the remote control, and then press
[OUTPUT] on the front panel or [VCR] on the remote control.
If you want to use the DVD player during a Timer Recording or while
• Press [POWER] to turn on the unit. Press [DVD] on the remote control to choose DVD mode, then continue with the other
DVD features as described in this manual.
NOTE (For Timer Recording) :
• If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.
PROGRAM NUMBER 1
B ONCE
DAILY
WEEKLY
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 2 3 MON
START TIME – – : – – – –
END
TIME – – : – – – –
L1/L2
– –
REC SPEED – –
.
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 2 3 MON
START TIME 0 7 : 3 0 – –
END
TIME – – : – – – –
L1/L2
– –
REC SPEED – –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END
TIME – – : – – – –
L1/L2
– –
REC SPEED – –
AM
B PM
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END
TIME 0 8 : 3 0 PM
L1/L2
L1
REC SPEED – –
indicator on the front panel blinks and Timer Recording cannot
indicator on the front panel lights up. To use the VCR as usual until the time for the
indicator light turns off.
– 13 –
9
Select recording speed,
then press [CLEAR/C.RESET].
CLEAR/
C. RESET
or
• To set another program after step 9, press [B].
Then, continue with step 2.
10
Press [T-SET] to set timer standby mode.
T-SET
•
indicator on the front panel lights up. The unit will change
to the DVD mode.
Hint
• To go back one step, press [s] during steps 3 to 9.
• L1 or L2 refers to rear or front input jacks. L1 activates rear input
jacks, L2 activates front input jacks.
To Check, Correct or Cancel a Timer Program
1) Press [T-SET] then, [VCR] on the remote control.
2) Select main menu by pressing [SETUP].
3) Select "TIMER PROGRAMMING" by using [K/L], then
press [B].
4) Select the program number which you want to check by
using [K/L]. The details of the program you selected will
appear on the TV screen.
• Go to the digit you want to change by using [s/ B].
Then, enter correct numbers by using [K/L].
• You may cancel the entire program by pressing [s]
while the program number blinks.
5) Press [CLEAR/C.RESET] to exit.
6) Press [T-SET] to return to timer standby mode.
To cancel a Timer Recording in progress
Press [STOP/EJECT C A] on the unit.
indicator on the front panel is on or blinking.
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE
1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END
TIME 0 8 : 3 0 PM
L1/L2
L1
REC SPEED SP
B SP
SLP
EN
Advertisement
Table of Contents
