Central Pneumatic 98751 Set Up And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Central Pneumatic Manuals
  4. Nail Gun
  5. 98751
  6. Set up and operating instructions manual

Central Pneumatic 98751 Set Up And Operating Instructions Manual

3-in-1 air framing nailer
Hide thumbs Also See for 98751:

Advertisement

Table of Contents

3-IN-1 AIR FRAMING NAILER
SET UP AND OPERATING INSTRUCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
Copyright
2008 by Harbor Freight Tools
or any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools. Diagrams within this manual may not be
drawn proportionally. Due to continuing improvements, actual product may differ slightly
from the product described herein. Tools required for assembly and service may not be
included.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 11a
98751
®
. All rights reserved. No portion of this manual

Advertisement

Table of Contents
loading

Related Manuals for Central Pneumatic 98751

Summary of Contents for Central Pneumatic 98751

  • Page 1 Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
  • Page 2 Keep bystanders, children, and minor or moderate injury. visitors away while operating the SKU 98751 For technical questions, please call 1-800-444-3353. Page 2...

  • Page 3: Personal Safety

    Fire nails into an appropriate work be used for the applicable surface only. Do not attempt to fire conditions. Wear heavy-duty work SKU 98751 For technical questions, please call 1-800-444-3353. Page 3...

  • Page 4: Air Source

    (70 to trained persons. A tool is dangerous 120 PSI). Always verify prior to using in the hands of untrained users. SKU 98751 For technical questions, please call 1-800-444-3353. Page 4...

  • Page 5: Symbols And Specific Safety Instructions

    Eye Injury. Wear ANSI-approved eye protection. approved safety equipment, such as Chart continued in next column. those dust masks that are specially designed to filter out microscopic SKU 98751 For technical questions, please call 1-800-444-3353. Page 5...
  • Page 6 This tool vibrates during use. Re- peated or long-term exposure to vibra- INSTRUCTIONS. tion may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: SKU 98751 For technical questions, please call 1-800-444-3353. Page 6...

  • Page 7: Functional Description

    Attach an air hose to the compres- any parts are missing or broken, please sor’s air outlet. Connect the air hose call Harbor Freight Tools at the number to the air inlet of the tool. Other com- shown throughout the manual as soon as ponents, such as a connector and possible.
  • Page 8 Air Tool & Spray Gun Portable Setup SKU 98751 For technical questions, please call 1-800-444-3353. Page 8...
  • Page 9 Air Tool & Spray Gun Stationary Setup SKU 98751 For technical questions, please call 1-800-444-3353. Page 9...
  • Page 10 ALWAYS point the Nailer at a discharge the tool in a safe fashion piece of scrap wood when testing. after disconnecting to ensure that the tool is disconnected and unpowered. Completely empty Magazine (79). SKU 98751 For technical questions, please call 1-800-444-3353. Page 10...

  • Page 11: Loading Nails

    Release the Trigger and squeeze tool. If there are only a few nails it again. The tool must not cycle remaining, simply load another strip (fire). With the Trigger held, carefully SKU 98751 For technical questions, please call 1-800-444-3353. Page 11...

  • Page 12: Operating Nailer

    Attach air supply to Air Coupler. Start your air compressor and make sure it Figure 4 is set to between the recommended Remove the Adjuster Knob (85). See 70-120 PSI. Figure 4, above. SKU 98751 For technical questions, please call 1-800-444-3353. Page 12...

  • Page 13: Clearing Jams

    ANSI-approved impact safety goggles and appro- priate hearing protection. THEN: Be careful. When pulling back the Tab, it will spring forward with a. Disconnect the Nailer from its air supply. SKU 98751 For technical questions, please call 1-800-444-3353. Page 13...
  • Page 14 Trigger or Safety Nosepiece sticks. Wipe down exterior of the Nailer with a clean cloth before storing. Store in a clean, dry and safe location out of reach of children. REV 09e SKU 98751 For technical questions, please call 1-800-444-3353. Page 14...

  • Page 15: Troubleshooting

    AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. REV 08j SKU 98751 For technical questions, please call 1-800-444-3353. Page 15...

  • Page 16: Parts List

    Bushing Rubber Cover Spring Pin Soft Grip Sleeve Safe Guide O-Ring (M65.4 X 2.5) O-Ring (M20.3 x 2.5) End Cap O-Ring (M20.3 x 1.5) Air Coupler Valve Set REV 10a SKU 98751 For technical questions, please call 1-800-444-3353. Page 16...
  • Page 17 Parts Diagram ASSEMBLY DIAGRAM Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 73 74 REV 10a SKU 98751 For technical questions, please call 1-800-444-3353. Page 17...
  • Page 18 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.

Table of Contents