Carrier 58CTA, 58CTX Product Data page 12

DIMENSIONS
5 15/16 5 15/16
[150.7] [150.7]
AIR FLOW AIR FLOW
5 1/2 5 1/2
[140.3] [140.3]
Ø7/8 Ø7/8
8 7/16 8 7/16
[22.2] [22.2]
[213.5] [213.5]
ACCESSORY ACCESSORY
9 7/8 9 7/8
[250.7] [250.7]
Ø1/2 Ø1/2
[12.7] [12.7]
27 3/4 27 3/4
THERMOSTAT WIRE ENTRY THERMOSTAT WIRE ENTRY
[704.7] [704.7]
33 1/4 33 1/4
[843.9] [843.9]
Ø7/8 Ø7/8
[22.2] [22.2]
ACCESSORY ACCESSORY
21.6 21.6
[549.5] [549.5]
BOTTOM INLET BOTTOM INLET
28.39 28.39
[721.2] [721.2]
29 29
[736.9] [736.9]
NOTES:
1. Two additional 7/8 ---in. (22 mm) diameter holes are located in the top plate.
2. Minimum return ---air openings at furnace, based on metal duct. If flex duct is used, see flex duct manufacturer's recommendations for equivalent diameters.
a. For 800 CFM ---16 ---in. (406 mm) round or 14 1/2 x 12 ---in. (368 x 305 mm) rectangle.
b. For 1200 CFM ---20 ---in. (508 mm) round or 14 1/2 x 19 1/2 ---in. (368 x 495 mm) rectangle.
c. For 1600 CFM ---22 ---in. (559 mm) round or 14 1/2 x 22 1/16 ---in. (368 x 560mm) rectangle.
d. For airflow requirements above 1800 CFM, see Air Delivery table in Product Data literature for specific use of single side inlets. The use of both side inlets,
a combination of 1 side and the bottom, or the bottom only will ensure adequate return air openings for airflow requirements above 1800 CFM.
A
CABINET
FURNACE
WIDTH
SIZE
IN (mm)
045---08 14--- 3/16 (360)
045---12
14--- 3/16 (360)
070---08 14--- 3/16 (360)
070---12 14--- 3/16 (360)
070---16 17--- 1/2 (445)
090---14 17--- 1/2 (445)
090---16
21 (533)
090---20 21 (533)
110---12 17--- 1/2 (445)
110---16 21 (533)
110---22 21 (533)
135---16 21 (533)
135---22
24--- 1/2 (622)
155---20 24--- 1/2 (622)
*135 and 155 size furnaces require a 5 or 6 ---in. (127 or 152 mm) vent. Use a vent adapter between furnace and vent stack. See Installation Instructions for
complete installation requirements.
5.1 5.1
[130.5] [130.5]
2 1/16 2 1/16
[51.6] [51.6]
1.7 1.7
[43.5] [43.5]
C
Ø7/8 Ø7/8
[22.2] [22.2]
ACCESSORY (2) ACCESSORY (2)
1 15/16 1 15/16
[49.2] [49.2]
AIR FLOW AIR FLOW
2 5/16 2 5/16
3 7/16 3 7/16
[59] [59]
A A
[86.8] [86.8]
B
5 7/8 5 7/8
[148.5] [148.5]
TOP OF CASING TOP OF CASING
Ø7/8 Ø7/8
[22.2] [22.2]
JUNCTION BOX JUNCTION BOX
LOCATION LOCATION
Ø1 3/4 Ø1 3/4
[44.5] [44.5]
GAS ENTRY GAS ENTRY
6.1 6.1
D
[155.7] [155.7]
BOTTOM RETURN BOTTOM RETURN
WIDTH WIDTH
B C
OUTLET TOP AND
WIDTH BOTTOM FLUE
IN (mm) COLLAR
IN (mm)
12--- 9/16 (319) 9--- 5/16 (237)
12--- 9/16 (319) 9--- 5/16 (237)
12--- 9/16 (319) 9--- 5/16 (237)
12--- 9/16 (319) 9--- 5/16 (237)
15--- 7/8 (403) 11--- 9/16 (294)
15--- 7/8 (403) 11--- 9/16 (294)
19--- 3/8 (492) 13--- 5/16 (338)
19--- 3/8 (492) 13--- 5/16 (338)
15--- 7/8 (403) 11--- 9/16 (294)
19--- 3/8 (492) 13--- 5/16 (338)
19--- 3/8 (492) 13--- 5/16 (338)
19--- 3/8 (492) 13--- 5/16 (338)
22--- 7/8 (581) 15--- 1/16 (383)
22--- 7/8 (581) 15--- 1/16 (383)
6 13/16 6 13/16
[172.3] [172.3]
5 7/8 5 7/8
[148.5] [148.5] 5 5/8 5 5/8
[143.3] [143.3]
5 7/16 5 7/16
[138.5] [138.5]
1 15/16 1 15/16
[49.2] [49.2]
TOP OF CASING TOP OF CASING
4 13/16 4 13/16
[122.2] [122.2]
9 9/16 9 9/16
[243.3] [243.3]
Ø7/8 Ø7/8
27 3/4 27 3/4
[22.2] [22.2]
[704.7] [704.7]
J.BOX PROVISION J.BOX PROVISION
Ø7/8 Ø7/8
29 9/16 29 9/16
[750.7] [750.7] [22.2] [22.2]
ACCESSORY ACCESSORY
KNOCK OUTS FOR KNOCK OUTS FOR
3/4 3/4
VENTING(5 VENTING(5
[19.1] [19.1]
PLACES) PLACES)
D
VENT
BOTTOM
CONNECTION
INLET WIDTH
SIZE
IN (mm)
IN (mm)
12--- 11/16 (322) 4 (102)
12--- 11/16 (322) 4 (102)
12--- 11/16 (322) 4 (102)
12--- 11/16 (322) 4 (102)
16--- 1/8 (410) 4 (102)
16--- 1/8 (410) 4 (102)
19--- 1/2 (495) 4 (102)
19--- 1/2 (495) 4 (102)
16--- 1/8 (410) 4 (102)
19--- 1/2 (495) 4 (102)
19--- 1/2 (495) 4 (102)
19--- 1/2 (495) 4 (102)*
23 (584) 4 (102))*
23 (584) 4 (102)*
12
8 5/8 8 5/8
[219] [219]
AIR FLOW AIR FLOW
19 19
[481.7] [481.7]
OUTLET OUTLET
Ø1/2 Ø1/2
[12.7] [12.7]
7 13/16 7 13/16
9 11/16 9 11/16
THERMOSTAT WIRE ENTRY THERMOSTAT WIRE ENTRY
[197.8] [197.8]
[245.4] [245.4]
11 7/16 11 7/16
Ø1 3/4 Ø1 3/4
[44.5] [44.5]
GAS ENTRY GAS ENTRY
14 7/8 14 7/8
Ø7/8 Ø7/8
[337.3] [337.3]
[22.2] [22.2]
(BOTH SIDES) (BOTH SIDES)
ACCESSORY ACCESSORY
1 1/4 1 1/4
[31.8] [31.8]
22 1/16 22 1/16 1
[560] [560] [25.4] [25.4]
SIDE INLET SIDE INLET
(BOTH SIDES) (BOTH SIDES)
A10270
ACCESSORY
SHIP WT MEDIA
CABINET SIZE
LB (KG)
IN (mm)
104 (47) 16 (406)
107 (49) 16 (406)
111 (50) 16 (406)
115 (52) 16 (406)
126 (57) 16 (406)
127 (58) 16 (406)
140 (64) 20 (508)
146 (66) 20 (508)
135 (61) 16 (406)
146 (66) 20 (508)
152 (69) 20 (508)
149 (68) 20 (508)
163 (74) 24 (610)
170 (77) 24 (610)
[290.7] [290.7]